KOLINK ARGB MIDI Tower Case

CUTAR PANEL

• Ƙungiyar Hagu – Buɗe ƙofar gabaɗaya ta amfani da hanun att:adied kuma cire hinges.
• Ƙungiyar Dama - Cire babban yatsan yatsa biyu kuma zamewa.
• Panel na gaba - Nemo yanke ƙasa, daidaita chassis da hannu ɗaya, kuma a cire daga yanke tare da ɗan ƙarfi:e har sai an fitar da shirye-shiryen bidiyo.

FASSARAR DARIYA

• Daidaita motherboard ɗinku tare da chassis zuwa I ko.ate inda yakamata a shigar da abubuwan tsayawa. Da zarar an gama, cire motherboard ɗin kuma ɗaure tsayawa daidai daidai.
• Saka farantin 1/0 na uwa a cikin yanke a bayan harka.
• Sanya mahaifar ku a cikin chassis, tabbatar da cewa tashoshin baya sun dace da farantin 1/0.
• Yi amfani da screws ɗin da aka bayar don haɗa motherboard ɗin ku zuwa chassis.

D ACCESSORY BACK

SHIGA WUTA

• Sanya PSU a baya na karar, a cikin PSU shroud.
• Daidaita ramukan kuma kiyaye tare da sukurori.

 KATIN KYAUTA/CIYAR KAtin PCI-E

• Cire murfin PCI-E na baya kamar yadda ya cancanta {ya danganta da girman ramin katin ku), Sanya a hankali kuma zame katin PCI-E ɗinku zuwa wuri, sannan amintaccen tare da skru na katin ƙara da aka kawo.
• Idan yana hawa a tsaye, haɗa madaidaicin sashin GPU na tsaye zuwa yankin ramin PCI-E, kiyaye kebul ɗin hawan PCI-E zuwa gareta (wanda aka sayar daban) kuma haɗa kebul ɗin zuwa uwayen uwa. Sanya katin PCI-E ɗinku a hankali, haɗe zuwa ramukan PCI-E na baya kuma amintacce tare da abubuwan ƙarawa da aka kawo.

SHIGA HDD

Sanya 3.5 ″ HOD cikin/ saman madaidaicin HOD da dunƙule ciki idan an buƙata.

SSD INSTALLATION (REAR

• • Cire madaidaicin daga bayan farantin motherboard,
  • Haɗa tuƙin 2.5 ″ ɗinku sannan ku dunƙule cikin wurin Sanya 2.5 ″ HDD/55□ cikin/a saman madaidaicin HOD kuma ku dunƙule ciki idan an buƙata.

 KYAUTA FAN INSTALLATION

• • Cire tacewa kura daga saman akwati.
  • Daidaita magoya bayan ku zuwa ramukan dunƙule a saman chassis kuma amintattu da sukurori.
  • Sauya tacewar ku da zarar an amintu.

FAN GABA / BAYAN SHIGA

ales your azumi ga kururuwa heles a kan chases.

SANIN RUWA RADIATOR

Amince da magoya baya zuwa radiator, sannan a ɗaure th!! radiyo lnsidl! chassis ta hanyar kullawa da skru daga waje,

SHIGA PANEL

• A hankali kunci lakabin kowane mai haɗawa daga panel 1/0 don gane aikin su.
• Ketare tunani tare da littafin uwa na uwa don gano inda ya kamata a sanya kowace waya, sannan a kiyaye daya bayan daya. Da fatan za a tabbatar an shigar da su a daidai polarity don guje wa rashin f111ction ko lalacewa.

Pro Gamers ware GmbH

• Gaul3stral3e 1, 10589 Berlin, Deutschland
• info@gamersware.com
• +49 (0) 30 83797272
• www.kolink.eu I support@kolink.eu

Takardu / Albarkatu

KOLINK ARGB MIDI Tower Case [pdf] Manual mai amfani ARGB MIDI Tower Case, ARGB, MIDI Tower Case, Hasumiyar Case, Case

Magana

• Manual mai amfani