Mai sarrafa Wutar Lantarki Mk2 Network Termination Kit

Bayanin samfur

The Power Control Processor Mk2 (PCP-Mk2) wani sashi ne da ake amfani dashi a cikin Echo Relay Panel Mains Feed da Elaho Relay Panel Mains Feed (ERP Mains Feed), Echo Relay Panel Feedthrough da Elaho Relay Panel Feedthrough (ERP Feedthrough), da Sensor IQ tsarin. . Kit ɗin ƙarewar hanyar sadarwa ta PCP-Mk2 ya haɗa da masu haɗin Cat5, akwatin Cat5 mai tsayi, tef mai tsayi biyu, da igiyoyin facin Cat5. Ana samun kit ɗin a cikin bambance-bambancen guda biyu, 7123K1129 ERP-FT da 7131K1029 Sensor IQPCP-Mk2 Network Termination Kits, da 7123K1029 ERP PCP-Mk2 Network Termination Kit. An ƙera samfurin don taimaka wa masu amfani da wayar da masu haɗin kai da kuma haɗa su cikin sassan da nagarta sosai.

Amfanin Samfur

GARGADI: HADARIN MUTUWA TA GIDAN LANTARKI!
Kafin yin aiki a cikin panel, tabbatar da cewa an katse duk ikon da ke kan panel don guje wa mummunan rauni ko mutuwa.

Kayan aikin da ake buƙata

Masu amfani suna buƙatar Jagoran Retrofit ETC, Mai sarrafa Wutar Lantarki Mk2 Network Termination Kit, da daidaitattun kayan aikin shigarwa na Cat5.

Waya Mai Haɗawa

Bi waɗannan matakan don waya da mahaɗin daɗaɗɗen dutsen Rukunin 5:

1. Bar tsawon kusan 25 cm (inci 10) a cikin panel don haɗawa da rashin ƙarfi don buƙatun sabis na gaba.
2. Bi daidaitattun hanyoyin shigarwa na Cat5 don cire ƙarshen jaket ɗin kebul da fallasa masu gudanarwa.
3. Cire madugu kuma a jera su bisa ga alamomin launi T568B. Saka masu gudanarwa a cikin hular haɗi. Jaket ɗin kebul ya kamata ya zo kusa da gefen mai haɗawa tare da kaɗan daga cikin masu gudanarwa da ake iya gani sosai. In ba haka ba, yanke kebul ɗin daidai kuma a sake farawa.
4. Idan kowane madugu ya wuce gefen hular haɗin haɗin, a datse abin da ya wuce gona da iri ta yadda ƙarshen madugu su riƙa ja da gefen hular haɗin.
5. Latsa hula da ƙarfi akan tushen mai haɗawa har sai sassan biyu sun ɗaga tare. Yi amfani da filashin haɗin gwiwa na zamewa don amfani da matsi daidai gwargwado a saman hular kuma don tabbatar da haɗin, amma tabbatar da cewa kar a karya robobin yayin da ake matsa lamba.

Haɗa Mai Haɗi zuwa Akwatin da Haɗawa

Bi waɗannan matakan don haɗa haɗin zuwa akwatin kuma haɗa:

1. Saka gefen gaba na mai haɗawa cikin akwatin hawa don ramin da ke gefen gaba na mahaɗin ya daidaita da shafin a ɓangaren ƙasa na akwatin.
2. Tura ƙasa a bayan mai haɗin don ɗaukar shi cikin akwatin.
3. A bayan murfin yana da ƙaramin yanke mai siffa U. Cire wannan yanke don ba da damar kebul ɗin ta wuce ba tare da an danne shi ba. Yi hanyar kebul ta hanyar jagorar akwatin kamar yadda aka nuna.
4. Daidaita murfin tare da sashin ƙasa kuma haɗa guda biyu tare.

Shigar da Connector a cikin Panel

Yi amfani da tef ɗin mai gefe biyu da aka bayar a cikin kayan aikin sake gyarawa don haɗa ƙasan akwatin dutsen saman zuwa rukunin ku. Dubi misalai masu zuwa don tunani:

Bayan hašawa da akwatin-Mount zuwa panel, samfurin yana shirye don amfani.

Ƙarsheview

• Ana amfani da na'ura mai sarrafa wutar lantarki Mk2 (PCP-Mk2) a cikin Echo Relay Panel Mains Feed da Elho Relay Panel Mains Feed (ERP Mains Feed), Echo Relay Panel Feedthrough da Elaho Relay Panel Feedthrough (ERP Feedthrough), da Sensor IQ tsarin.
• GARGADI: HADARIN MUTUWA TA GIDAN LANTARKI! Rashin cire haɗin duk wutar lantarki zuwa panel kafin aiki a ciki na iya haifar da mummunan rauni ko mutuwa.
• Kashe babban ciyarwa zuwa kwamitin kuma bi Kulle/Kulle da ya dace.Tagfitar da hanyoyin kamar yadda NFPA 70E ta umarta. Yana da mahimmanci a lura cewa kayan wutan lantarki kamar na'urorin relay na iya haifar da hatsarin filasha idan ba a yi aiki da kyau ba. Wannan ya faru ne saboda yawan adadin gajeren lokaci da ake samu akan wutar lantarki ga wannan kayan aiki. Kowane aiki dole ne ya bi ka'idodin Aiki Amintaccen OSHA.

Kunshe a cikin Kit

7123K1129 ERP-FT da 7131K1029 Sensor IQPCP-Mk2 Kayayyakin Ƙarshen hanyar sadarwa

Bayani	ETC Part Number	Yawan
Mai haɗa Cat5	N2026	1
Surface-Mount Cat5 akwatin	N2025	1
Tef mai tsayi biyu, 1.5 inci	I342	1
1 ft Cat5 faci na USB	N4036	1

7123K1029 ERP PCP-Mk2 Kit ɗin Ƙarshen hanyar sadarwa

Bayani	ETC Part Number	Yawan
Mai haɗa Cat5	N2026	1
Surface-Mount Cat5 akwatin	N2025	1
Tef mai tsayi biyu, 1.5 inci	I342	1
Dutsen ɗaurin ɗaurin igiya	HW741	2
Tayin igiya	HW701	2
4 ft Cat5 faci na USB	N4009	1

Kayan aikin da ake buƙata

• Phillips sikeli
• Zamewa haɗin gwiwa pliers
• Kayan aikin sheathing ko abin yanka don jaket na USB na Cat5

Wire da Connector

Haɗin mahaɗin sama-fasa na 5 da aka kawo a cikin wannan kit ɗin ya haɗa da guda biyu: naúrar tushe da hula. Tafiyar tana da alamomi masu launi a gefe ɗaya don nuna inda za'a saka kowace wayoyi masu launi na kebul ɗin. Bi tsarin wayoyi na T568B, kamar yadda aka kwatanta akan sitiyar hula, don dacewa da tarurrukan wayoyi na hanyar sadarwa na ETC.

1. Bar tsawon kusan 25 cm (inci 10) a cikin panel don haɗawa da rashin ƙarfi don buƙatun sabis na gaba.
2.  Bi daidaitattun hanyoyin shigarwa na Cat5 don cire ƙarshen jaket ɗin kebul da fallasa masu gudanarwa:
   • Cire kusan 13 mm (1/2 in) na ƙarshen jaket ɗin kebul na waje ta amfani da kayan aikin sheathing ko mai yankewa, tabbatar da cewa kar a lalata rufin masu gudanarwa na ciki. Idan ɗaya ko fiye na madugu sun lalace yayin wannan aikin, yanke kebul ɗin daidai kuma a sake farawa.
3. Cire madugu kuma a jera su bisa ga alamomin launi T568B. Saka masu gudanarwa a cikin hular haɗi. Jaket ɗin kebul ya kamata ya zo kusa da gefen mai haɗawa tare da kaɗan daga cikin masu gudanarwa da ake iya gani sosai. In ba haka ba, yanke kebul ɗin daidai kuma a sake farawa.
4. Idan kowane madugu ya wuce gefen hular haɗin haɗin, a datse abin da ya wuce gona da iri ta yadda ƙarshen madugu su riƙa ja da gefen hular haɗin.
5. Latsa hula da ƙarfi akan tushen mai haɗawa har sai sassan biyu sun ɗaga tare. Yi amfani da filashin haɗin gwiwa na zamewa don amfani da matsi daidai gwargwado a saman hular kuma don tabbatar da haɗin, amma tabbatar da cewa kar a karya robobin yayin da ake matsa lamba.

   

Shigar da Connector a cikin Panel

Yi amfani da tef ɗin mai gefe biyu da aka bayar a cikin kayan aikin sake gyarawa don haɗa ƙasan akwatin dutsen saman zuwa rukunin ku. Dubi misalai na gaba. Dubi misalin nan.

Haɗa Faci Cable

ERP Feedthrough ko Sensor IQ
Haɗa kebul ɗin faci mai tsayi ft 1 (N4036) daga mahaɗin dutsen sama zuwa bayan mahaɗin mai amfani.

Lura: Sensor IQ da aka nuna a sama an ɗora shi a cikin madaidaicin matakin ciyarwa

Ciyarwar Ma'auni na ERP

Babban Ciyarwa

1. Yi hanyar kebul na facin hanyar sadarwa ta 4 ft (N4009) ta cikin kebul ɗin ribbon buɗewa a cikin kasan shingen mahaɗan mai amfani, a bayan rukunin hawan katin ba da sanda zuwa akwatin saman dutsen.
   • Kit ɗin ya haɗa da igiyar igiyar igiya da igiyar igiya mai ɗaure don suturar kebul ɗin faci, kamar yadda ake buƙata.
2. Haɗa kebul ɗin faci zuwa akwatin dutsen saman.
3. Haɗa kebul ɗin faci zuwa bayan mahaɗin mai amfani.

   

Ciyarwar ƙasa

1. Yi hanyar kebul na facin hanyar sadarwa na 4 ft (N4009) daga akwatin dutsen saman, a bayan kwamitin hawan katin ba da sanda, kuma ta hanyar buɗe kebul na ribbon a ƙasan shingen mai amfani.
   • Kit ɗin ya haɗa da igiyar igiyar igiya da igiyar igiya mai ɗaure don suturar kebul ɗin faci, kamar yadda ake buƙata.
2. Haɗa kebul ɗin faci zuwa bayan mahaɗin mai amfani.
3. Haɗa kebul ɗin faci zuwa akwatin dutsen saman.

Takardu / Albarkatu

ECHO Power Control Processor Mk2 Network Termination Kit [pdf] Jagorar mai amfani Mai sarrafa Wutar Lantarki Mk2, Kit ɗin Ƙarshen Sadarwar Sadarwar, Mai sarrafa Wutar Lantarki Mk2 Network Termination Kit, Kit ɗin Ƙarshe, PCP-Mk2

Magana

• Manual mai amfani