REGULAR INSTALLATION
ADDENDUM – SUGGESTED WIRING CONFIGURATION
Immobilizer Bypass And Data Interface Module
ONLY COMPATIBLE WITH AUTOMATIC TRANSMISSION VEHICLES.
| VEHICLE | YEARS | PK3, Passlock | Lock | Unlock | Tachometer | Parking Light |
| Rendez-vous | Automatic transmission 2002-2007 | • | • | • | • | • |
 |
BYPASS FIRMWARE VERSION 70.18 ONLY SEULEMENT |
To add the firmware version and the options, use the FLASH LINK UPDATER or FLASH LINK MOBILE tool, sold separately. |
| UNIT OPTION OPTION UNITE |
DESCRIPTION | ||
|
Program bypass option AUTOMATIC TRANSMISSION ONLY: |
A7 |
Foot Brake (output Status) |
| Frein pied (Status Sortie) |
NOTES
PK3 indicator will be ON during remote start but will turn OFF when the key is inserted in to the ignition barrel
MANDATORY INSTALL
* HOOD PIN
HOOD STATUS : THE HOOD PIN SWITCH MUST BE INSTALLED IF THE VEHICLE CAN BE REMOTE STARTED WITH THE HOOD OPEN.
Notice: the installation of safety elements are mandatory. The hood pin is an essential security element and must be installed.
THIS MODULE MUST BE INSTALLED BY A QUALIFIED TECHNICIAN. A WRONG CONNECTION CAN CAUSE PERMANENT DAMAGE TO THE VEHICLE.
DESCRIPTION
WIRING CONNECTION
KEY BYPASS PROGRAMMING PROCEDURE
Press and hold the programming button: Connect the 6-PIN Main harness (White connector).
The Blue, Red, Yellow and Blue & Red LEDs will alternatively illuminate.
Release the programming button when the LED is BLUE.
If the LED is not solid BLUE disconnect the 6-Pin connector (Main-Harness) and go back to step 1.
Insert the required remaining connector
Turn the key to the Ignition ON/RUN position.
The BLUE LED will turn off.
The RED LED will turn ON.
The RED LED will flash.
Start the vehicle and hold at START position for 3 seconds
The RED LED will turn off and the YELLOW LED will turn ON.
Turn the key to the OFF position.
The LED will turn OFF.
REMOTE STARTER PROGRAMMING PROCEDURE
REFER TO THE QUICK INSTALL GUIDE INCLUDED WITH THE MODULE FOR THE REMOTE STARTER PROGRAMMING.
REMOTE STARTER FUNCTIONALITY
 |
 |
 |
| All doors must be closed. | Remote start the vehicle. | Unlock the doors with the remote-starter remote or the OEM remote. |
 |
 |
 |
| Insert and Turn the key to the Ignition ON/RUN position. | Press the brake pedal. | The vehicle can now be put in to gear and driven. |
Notice: Updated Firmware and Installation Guides
Updated firmware and installation guides are posted on our web site on a regular basis. We recommend that you update this module to the latest firmware and download the latest installation guide(s) prior to the installation of this product.
WARNING
The information on this sheet is provided on an (as is) basis with no representation or warranty of accuracy whatsoever.
It is the sole responsibility of the installer to check and verify any circuit before connecting to it. Only a computer safe logic probe or digital multimeter should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or responsibility whatsoever pertaining to the accuracy or currency of the information supplied. The installation in every case is the sole responsibility of the installer performing the work and FORTIN ELECTRONIC SYSTEMS assumes no liability or responsibility whatsoever resulting from any type of installation, whether performed properly, improperly or any other way. Neither the manufacturer or distributor of this module is responsible of damages of any kind indirectly or directly caused by this module, except for the replacement of this module in case of manufacturing defects. This module must be installed by qualifi ed technician. The information supplied is a guide only. This instruction guide may change without notice. Visit www.fortinbypass.com to get the latest version.
 |
TECH SUPPORT Tél: 514-255-HELP (4357) 1-877-336-7797 |
 |
ADDENDUM GUIDE |
www.fortinbypass.com
WEB UPDATE
Documents / Resources
 |
FORTIN Immobilizer Bypass And Data Interface Module [pdf] Instruction Manual Immobilizer Bypass And Data Interface Module, Bypass And Data Interface Module, And Data Interface Module, Data Interface Module, Interface Module |