TLK2 Camry STD Key
“
Specifications:
- Make: DL-TL9 Toyota
- Model: Camry STD Key (H)
- Year Install: 2018-20
- Type: 5
- CAN ECU
Product Usage Instructions:
Installation Requirements:
This installation requires BLADE-AL(DL)-TL9 firmware, flash
module, and updating the controller before beginning the
installation.
CAN Data Connections:
CAN data connections are handled through connections at the ECU;
no other connections are required.
TPMS Ignition:
The TPMS ignition wire, located in the 36-pin connector of the
Main Body ECU, must be interrupted if 3X Lock control is required.
If not required, and aftermarket remotes are being used, no
connection is necessary.
Parking Lights:
TL9 firmware handles parking lights through data. If issues
arise, the +parking light (green/white) can be used.
Keysense & RAP:
The TLK2 harness includes pre-terminated connections for
Keysense and RAP circuits. Keysense (brown/white) is only required
in manual transmission applications. RAP (orange) connects to the
driver door circuit.
I/O Changes:
No changes are required for I/O configurations.
FAQ:
Q: What do I do if the Module LED flashes RED during
programming?
A: Error codes are as follows:
- 1x – No CAN activity, check harness connections.
- 2x – No analog Ignition, check harness connections.
- 3x – No Immobilizer data, check SIL to OBD connection.
- 4x – VIN received but not in table, contact iDatalink.
“`
FTI-TLK2: Vehicle Coverage and Preparation Notes
Make
DL-TL9 Toyota
Model Camry STD Key (H)
Year
Install
2018-20
Type 5
CAN ECU
Lights IMI/IMO TPMS I/O Changes
Park / Auto
DATA
SIL*
OBD 7/16
Type 3 35/36
Green White/Blue
N/A
This install requires BLADE-AL(DL)-TL9 firmware, flash module and update the controller before beginnning the installation.
CAN: CAN data connections are handled through connections at the ECU, no other connections are required.
SIL (immobilizer)/RDA: SIL data connection is made at the OBD-II connector, using the pre-terminated orange/black wire included with this kit. Additional modification of the harness BLADE connector is required: Step 1.) Remove the existing orange/black wire from the harness BLADE connector, replace it with the pre-terminated wire, then connect to the blue SIL data wire located at pin #7 of the vehicle OBD-II connector. Step 2.) The Camry RDA connection uses the orange /black wire that was removed in Step 1, by removing the green/red wire in the BLADE connector, and replacing it with the orange/black. See illustration on next page.
TPMS Ignition: The TPMS ignition wire, located in the 36-pin connector of the Main Body ECU, must be interrupted if 3X Lock control is required. If the feature is not required, and aftermarket remotes are being used, no connection is necessary.
Parking Lights: TL9 firmware handles parking lights through data, if issues arise the +parking light (green/white) can be used.
Keysense & RAP: The TLK2 harness includes pre-terminated connections for Keysense and RAP circuits. Keysense (brown/white) is only required in manual transmission applications, insert CM I/O connector keysense position. RAP (orange) connects to the driver door circuit, insert in any POC position and configure for RAP in the feature options.
I/O Changes: No changes are required.
FTI-TLK2: Installation and Configuration Notes
CM-X
IIIIIIIII
A CONNECTIONS REQUIRED B CONNECTION REQUIRED C NOT REQUIRED D OPTIONAL CONNECTION E OPTIONAL CONNECTION
IIIIIIIIIIIIIIIIIIIIIIEIIIRIIIIIIIIIIIIIIIIIIIIIIIIIIIII
D LAN
2001
O
O
Z
K E R E D
st. E
IIIIIIIII
S
ID
D
KO O
rG
fo AD E
R R
E ‘T T AN NC
CE AND
WHO
O H W
WANNA
LEARN
TO
* available only when ignition is off ** if equipped with factory hood pin switch
FEATURE COVERAGE
CM7000/7200
Cut loop for A/T CMX
CM7X00
CCMMX 9H0ig0hACSur/r9e0nt0PSroJgurammmpaebrle (+) Output Channels
HCP #1 – Parking Light HCP #2 – Accessory HCP #3 – Ignition
[ 2 ] 2ND START [ 3 ] 2ND IGNITION [ 4 ] 2ND ACCESSORY CM-900S/900AS
IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII D
O OTHER STUFF GOOD TOO
IMMOBILIZER DATA PRIORITY UNLOCK ARM OEM ALARM DISARM OEM ALARM DOOR LOCK DOOR UNLOCK PARKING LIGHT CONTROL POWER LIFTGATE TRUNK/HATCH RELEASE* DOOR STATUS TRUNK STATUS HOOD STATUS ** TACH OUTPUT BRAKE STATUS E-BRAKE STATUS A/M ALARM CTRL FROM OEM REMOTE A/M RS CONTROL FROM OEM REMOTE
CM -900
FTI-TLK2 – DL-TL9 – Type 5 2018-20 Toyota Camry STD Key (H)
No Connection
BLADE
GWR +12V
DRIVER DOOR
SET POC FOR
RAP (31)
A
PWR
See next page for image of completed modification
A
RDA Modification: 1- Remove grn/red 2- Insert org/blk
3- Remove gry/red 4- Insert provided
org/blk SIL wire
6 12
3
35
4
Ignition Connector
1
Keysense
2
Main Body ECU
3
immobilizer data
E
(+) PARKING LIGHTS
OPTIONAL CONNECTION 6
Autolight Shutdown white or yellow
SIL Data Connection
OBD-II
B4
1
7
16
18
10
40
36
9
55 33 1
23
19
C
white/black
white/red
D
TPMS Ignition (cut)
5
36 35
27
12
28 19 7 18 6
TL9 LED Programming Error Codes
Module LED flashing RED during programming
1x – No CAN activity, check harness connections. 2x – No analog Ignition, check harness connections. 3x – No Immobilizer data, check SIL to OBD connection. 4x – VIN received but not in table, contact iDatalink.
lt.purple/black
13 1 3D – WHITE
INSTALL GUIDE
Page 58 of 59
1
COM-BLADE-AL(DL)-TL9-EN
CARTRIDGE INSTALLATION
Slide cartridge into unit. Notice button under LED.
2
DOORLAOLLCKININOTNEERFACE SCTIOONY/OTOTYAOTA
Doc. No.: ##76832## 20210806
Ready for Module Programming Procedure.
MODULE PROGRAMMING PROCEDURE
NOTE
5
I IMPORTANT: The hood must be closed.
1
G
G
2
Use the BLACK key only.
6
OFF
DO NOT use the GRAY valet key.
7
Insert key into ignition.
Wait, LED will turn solid BLUE for 2 seconds.
Turn key to OFF position.
Module Programming Procedure completed.
3
Turn key to ON position.
ON
4
LED will turn solid RED.
Completed Modification
WWW.IDATALINK.COM
Automotive Data Solutions Inc. © 2020
Documents / Resources
 |
FIRSTECH TLK2 Camry STD Key [pdf] Instruction Manual TLK2 Camry STD Key, TLK2, Camry STD Key, Key |
