iDatalink - Home
Instruction Manual for FIRSTECH models including: TLK2 Camry STD Key, TLK2, Camry STD Key, Key
FTI-TLK2 | MyFirstech Install
File Info : application/pdf, 3 Pages, 271.38KB
DocumentDocumentFTI-TLK2: Vehicle Coverage and Preparation Notes Make DL-TL9 Toyota Model Camry STD Key (H) Year Install 2018-20 Type 5 CAN ECU Lights IMI/IMO TPMS I/O Changes Park / Auto DATA SIL* OBD 7/16 Type 3 35/36 Green White/Blue N/A This install requires BLADE-AL(DL)-TL9 firmware, flash module and update the controller before beginnning the installation. CAN: CAN data connections are handled through connections at the ECU, no other connections are required. SIL (immobilizer)/RDA: SIL data connection is made at the OBD-II connector, using the pre-terminated orange/black wire included with this kit. Additional modification of the harness BLADE connector is required: Step 1.) Remove the existing orange/black wire from the harness BLADE connector, replace it with the pre-terminated wire, then connect to the blue SIL data wire located at pin #7 of the vehicle OBD-II connector. Step 2.) The Camry RDA connection uses the orange /black wire that was removed in Step 1, by removing the green/red wire in the BLADE connector, and replacing it with the orange/black. See illustration on next page. TPMS Ignition: The TPMS ignition wire, located in the 36-pin connector of the Main Body ECU, must be interrupted if 3X Lock control is required. If the feature is not required, and aftermarket remotes are being used, no connection is necessary. Parking Lights: TL9 firmware handles parking lights through data, if issues arise the +parking light (green/white) can be used. Keysense & RAP: The TLK2 harness includes pre-terminated connections for Keysense and RAP circuits. Keysense (brown/white) is only required in manual transmission applications, insert CM I/O connector keysense position. RAP (orange) connects to the driver door circuit, insert in any POC position and configure for RAP in the feature options. I/O Changes: No changes are required. FTI-TLK2: Installation and Configuration Notes CM-X IIIIIIIII A CONNECTIONS REQUIRED B CONNECTION REQUIRED C NOT REQUIRED D OPTIONAL CONNECTION E OPTIONAL CONNECTION IIIIIIIIIIIIIIIIIIIIIIEIIIRIIIIIIIIIIIIIIIIIIIIIIIIIIIII D LAN 2001 O O Z K E R E D st. E IIIIIIIII S ID D KO O rG fo AD E R R E 'T T AN NC CE AND WHO O H W WANNA LEARN TO * available only when ignition is off ** if equipped with factory hood pin switch FEATURE COVERAGE CM7000/7200 Cut loop for A/T CMX CM7X00 CCMMX 9H0ig0hACSur/r9e0nt0PSroJgurammmpaebrle (+) Output Channels HCP #1 - Parking Light HCP #2 - Accessory HCP #3 - Ignition [ 2 ] 2ND START [ 3 ] 2ND IGNITION [ 4 ] 2ND ACCESSORY CM-900S/900AS IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII D O OTHER STUFF GOOD TOO IMMOBILIZER DATA PRIORITY UNLOCK ARM OEM ALARM DISARM OEM ALARM DOOR LOCK DOOR UNLOCK PARKING LIGHT CONTROL POWER LIFTGATE TRUNK/HATCH RELEASE* DOOR STATUS TRUNK STATUS HOOD STATUS ** TACH OUTPUT BRAKE STATUS E-BRAKE STATUS A/M ALARM CTRL FROM OEM REMOTE A/M RS CONTROL FROM OEM REMOTE CM -900 FTI-TLK2 - DL-TL9 - Type 5 2018-20 Toyota Camry STD Key (H) No Connection BLADE GWR +12V DRIVER DOOR SET POC FOR RAP (31) A PWR See next page for image of completed modification A RDA Modification: 1- Remove grn/red 2- Insert org/blk 3- Remove gry/red 4- Insert provided org/blk SIL wire 6 12 3 35 4 Ignition Connector 1 Keysense 2 Main Body ECU 3 immobilizer data E (+) PARKING LIGHTS OPTIONAL CONNECTION 6 Autolight Shutdown white or yellow SIL Data Connection OBD-II B4 1 7 16 18 10 40 36 9 55 33 1 23 19 C white/black white/red D TPMS Ignition (cut) 5 36 35 27 12 28 19 7 18 6 TL9 LED Programming Error Codes Module LED flashing RED during programming 1x - No CAN activity, check harness connections. 2x - No analog Ignition, check harness connections. 3x - No Immobilizer data, check SIL to OBD connection. 4x - VIN received but not in table, contact iDatalink. lt.purple/black 13 1 3D - WHITE INSTALL GUIDE Page 58 of 59 1 COM-BLADE-AL(DL)-TL9-EN CARTRIDGE INSTALLATION Slide cartridge into unit. Notice button under LED. 2 DOORLAOLLCKININOTNEERFACE SCTIOONY/OTOTYAOTA Doc. No.: ##76832## 20210806 Ready for Module Programming Procedure. MODULE PROGRAMMING PROCEDURE NOTE 5 I IMPORTANT: The hood must be closed. 1 G G 2 Use the BLACK key only. 6 OFF DO NOT use the GRAY valet key. 7 Insert key into ignition. Wait, LED will turn solid BLUE for 2 seconds. Turn key to OFF position. Module Programming Procedure completed. 3 Turn key to ON position. ON 4 LED will turn solid RED. Completed Modification WWW.IDATALINK.COM Automotive Data Solutions Inc. © 2020