FTI-CDP1: Notas de preparación y cobertura del vehículo
SUPPORT – 1(888) 820-3690, EXT. 203
| Make | DL-CH12 Jeep |
| Model | Compass PTS |
| Year | 2019 |
| Install | Type 3A |
| CAN | SGM |
| Lights | Park / Auto Type B2 |
| IGN | PSM |
| RAP | BCM |
| I/O Changes | Green White/Blue N/A |
FIRMWARE:
Esta instalación requiere BLADE-AL (DL) -CH12, módulo flash y actualización del firmware del controlador antes de la instalación.
INSTALACIÓN:
Los vehículos de tipo 3B utilizan conexiones CAN en el arnés en el conector OBD-II. El cable de extensión CAN incluido es no es necesario para este tipo de instalación.
LUCES:
Las luces de estacionamiento tipo H requieren que un controlador POC esté configurado para control de peligros (opción POC # 30) y conectado al circuito de peligro del vehículo en el BCM (conector C8, clavija # 59, verde claro / rojo). Los conectores del arnés de 6 y 10 pines no se utilizan.
ENCENDIDO:
El encendido tipo 3 está disponible en el conector del módulo de dirección asistida (negro, conector de 10 pines, pin n. ° 1, naranja / blanco), ubicado debajo del volante.
RAP:
La energía de los accesorios retenida se maneja mediante la provisión de arnés (naranja / blanco) y se conecta al pasador de la puerta del conductor circuito en el BCM (conector C6, patilla # 7, blanco violeta).
FTI-CDP1 – Notas de instalación y configuración
[A] CONEXIÓN REQUERIDA (OBD-II CAN)
[B] NO SE REQUIERE (extensión CAN)
[C] SIN CONEXIÓN
[D] CONEXIÓN REQUERIDA (IGN)
[E] CONEXIÓN REQUERIDA (DDP RAP)
[F] SE REQUIERE CONEXIÓN (Vea la nota de luces arriba)
COBERTURA DE FUNCIONES
| IMMOBILIZER DATA |  |
| ARM OEM ALARM | |
| DISARM OEM ALARM | |
| DOOR LOCK | |
| DOOR UNLOCK | |
| PRIORITY UNLOCK | |
| TRUNK/HATCH RELEASE | |
| POWER LIFTGATE | |
| POWER SLIDING DOOR (L) | |
| POWER SLIDING DOOR (R) | |
| SECURE TAKEOVER | |
| DOOR STATUS | |
| TRUNK STATUS | |
| HOOD STATUS | |
| E-BRAKE STATUS | |
| TACH OUTPUT | |
| BRAKE STATUS | |
| GLOW PLUG STATUS | |
| PARKING LIGHTS | |
| HAZARD LIGHTS | |
| A/M CONTROL | |
- FT-DAS Required for manual transmission.
- BOTH Red & Red/White MUST be connected with high current application.
Jumper Setting
- Parking Light
- Accessory
- Ignition (Default)
- (+) Door Trigger In
- (-) Door Trigger In (Default)
- Starter
- Ignition
- Accessory (Default)
- Parking Light (Default)
- Starter
- Trunk
- Cut loop for A/T
CM7000/7200
CM-900S/900AS
CM900AS/900S Jumper
- START
- ACC
- IGN1
FTI-CDP1 – DL-CH12 – Type 3B 2019 Jeep Compass PTS
SUPPORT – 1(888) 820-3690, EXT. 203
(1) OBD-II connector
(2) PTS Button
(3) Headlight switch
(4) Power Steering Module
(5) BCM
Códigos de error de programación de LED
El LED del módulo parpadea en ROJO durante la programación
1x – Error de CAN
2x – Código clave no aprendido
3x – Sin ENCENDIDO
4x – Sin inmovilizador, comprobar CAN / llave
5x – Error de VIN, verifique el cableado CAN
6x – Ver error 4x
7x – Error de KLON
8x – Sin ENCENDIDO, verifique la conexión
INSTALL GUIDE
ALL IN ONE
CHRYSLER/FIAT/JEEP
Patent No. US 8,856,780 CA 2759622
COM-BLADE-AL(DL)-CH12-EN
Doc. No.: ##72849##20201120
MODULE PROGRAMMING PROCEDURE – PTS
NOTE
I IMPORTANT: The hood must be closed.
1
Close driver door.
Re-open driver door to wake up data bus.
2
Press UNLOCK on OEM remote.
(If the vehicle is not equipped with an OEM remote, press on the module programming button.)
3
Wait, LED will flash BLUE once [1x]. If LED does not flash GREEN, repeat step 2.
4
Set ignition to ON position.
5
Wait, if LED turns solid RED proceed to step 6.
If LED flashes BLUE rapidly, proceed to step 10.
6
Set ignition to OFF position.
7
Repeat steps 4 to 6, eight times [8x].
8
Set ignition to ON position.
9
Wait, LED will flash BLUE rapidly.
10
Set ignition to OFF position.
11
WARNING:
Disconnect power last.
Disconnect module from vehicle.
12
Connect module to computer and proceed with extended programming.
13
WARNING: Do not press module programming button.
Connect power first.
Connect module to vehicle.
14
Set ignition to ON position.
15
Wait, LED will turn solid BLUE for 2 seconds.
16
Set ignition to OFF position.
17
Module Programming
Procedure completed.
WARNING: READ BEFORE REMOTE STARTING THE VEHICLE
IMPORTANT
I All vehicle doors must be closed and locked prior to remote start sequence. Failure to comply will result in remote starter malfunction.
TAKE OVER PROCEDURE – PTS – TO THE VEHICLE OWNER
NOTE
I All vehicle doors must be closed and locked prior to remote start sequence.
TIME RESTRICTI
N COMING UP !
1
Unlock vehicle door using OEM or after-market remote, or door request switch.
2
TIME RESTRICTIN
Within 45 SECONDS from previous step:
Open vehicle door.
Enter vehicle.
Close vehicle door.
Press and release BRAKE pedal.
3
Take over procedure completed.
Failure to follow procedure will result in vehicle engine shutdown.
WWW.IDATALINK.COM Automotive Data Solutions Inc. © 2020
Documents / Resources
 |
FIRSTECH DL-CH12 Compass PTS [pdf] Instruction Manual DL-CH12 Compass PTS, DL-CH12, Compass PTS, PTS |
 |
FIRSTECH DL-CH12 Compass PTS [pdf] Installation Guide DL-CH12 Compass PTS, DL-CH12, Compass PTS, PTS |
