SpeedyBee F405 V5 Stack BLS 55A 4-in-1 ESC & FC Instruction Manual

1. Johdanto

This manual provides detailed instructions for the installation, configuration, and operation of your SpeedyBee F405 V5 Flight Controller (FC) and BLS 55A 4-in-1 Electronic Speed Controller (ESC) stack. This high-performance stack is designed for FPV drones, offering advanced features and robust performance. Please read this manual thoroughly before use to ensure proper setup and safe operation.

2. Turvallisuustiedot

⚠️ Vain virkistyskäyttöön. Droonien/lentokoneiden laiton muokkaaminen on kielletty. Huomioithan myös omassa maassasi/alueellasi voimassa olevat droonien/lentokoneiden käyttöä koskevat lait ja määräykset varmistaaksesi laillisen käytön.

Always ensure correct polarity when connecting power. Incorrect wiring can cause severe damage to the components.
Exercise caution when soldering. Use appropriate safety gear and ensure proper ventilation.
Keep the stack away from moisture and extreme temperatures.
Irrota akku ennen huolto- tai muutostöiden tekemistä.
Ensure all connections are secure before powering on your drone.

3. Pakkauksen sisältö

The SpeedyBee F405 V5 Stack BLS 55A is available in different configurations. Please verify your package contents against the list below.

Vakiopaketin sisältö

SpeedyBee F405 V5 Stack Standard Package Contents — Standard Package Contents for SpeedyBee F405 V5 Stack.

SpeedyBee F405 V5 -mallin lento-ohjain x1
SpeedyBee OX32 55A 4-in-1 Model Aircraft ESC x1
Model Aircraft Stack Connector Cable (SH1.0 10pin*25mm) x1
Model Aircraft Stack Connector Cable (SH1.0 10pin*75mm) x1
DJI Air Unit Connector Cable (SH1.0 6pin*80mm) x1
GPS 6pin Connector Cable + 6pin SH1.0 Terminal x1 (SH1.0 6pin*120mm)
GPS 4-nastainen liitäntäkaapeli + 4-nastainen SH1.0-liitin x1 (SH1.0 6-nastainen - SH1.0 4-nastainen * 120 mm)
Vastaanottimen 4-nastainen liitäntäkaapeli x1 (SH1.0 4-nastainen * 100 mm)
XT60-virtakaapeli x1 (120 mm)
M3-mallin lentokonepinon kiinnitysruuvit x4 (30 mm)
M3 kuusiokolomutterit x5
M3 mustat silikonialuslevyt x5
Kondensaattorin kutistesukka x2
Pienoismallien FC-silikonisuojukset x5
Pienoismallien ESC-silikonisuojukset x5
35 V 1000 uF kiinteä kondensaattori x1
Pienoismallien pinon x1 pikaopas

Deluxe Package Contents

SpeedyBee F405 V5 -mallin lento-ohjain x1
SpeedyBee OX32 55A 4-in-1 Model Aircraft ESC x1
Juotosharjoittelukortti x1
Oikosulkusuojaustyökalu x1
Model Aircraft Stack Connector Cable (SH1.0 10pin*25mm) x1
Model Aircraft Stack Connector Cable (SH1.0 10pin*75mm) x1
DJI Air Unit Connector Cable (SH1.0 6pin*80mm) x1
GPS 6pin Connector Cable + 6pin SH1.0 Terminal x1 (SH1.0 6pin*120mm)
GPS 4-nastainen liitäntäkaapeli + 4-nastainen SH1.0-liitin x1 (SH1.0 6-nastainen - SH1.0 4-nastainen * 120 mm)
Vastaanottimen 4-nastainen liitäntäkaapeli x1 (SH1.0 4-nastainen * 100 mm)
Buzzer Red & Black Wires x1 (100mm)
Aktiivinen summeri x1
C-tyypin jatkomoduulin 4-nastainen liitinkaapeli x1 (SH1.0 4-nastainen * 80 mm)
C-tyypin laajennusmoduuli x1
M3 kuusiokolomutterit x5
M3 mustat silikonialuslevyt x5
Pienoismallien FC-silikonisuojukset x5
Pienoismallien ESC-silikonisuojukset x5
M3 Stack Mounting Screws x4 (30mm)
Virtalähdelaajennuskortti x4
Kondensaattorin kutistesukka x2
35 V 1000 uF kiinteä kondensaattori x1
Pienoismallien pinon x1 pikaopas

4. Tuote ohiview

SpeedyBee F405 V5 -lennonohjain

SpeedyBee F405 V5 Flight Controller Top View — Yläosa view of the SpeedyBee F405 V5 Flight Controller.

SpeedyBee F405 V5 Flight Controller Layout — Detailed layout of the F405 V5 Flight Controller, showing component labels and connections.

The F405 V5 Flight Controller features an STM32F405 MCU and an ICM42688P Gyro for precise flight control. It includes a built-in barometer (SPA06-003) for accurate altitude readings and an AT7456E OSD chip for on-screen display. Connectivity includes a new Type-C USB port and full-featured Bluetooth tuning via the SpeedyBee App, allowing for wireless firmware flashing and parameter tuning. It supports 6-pin direct plug-in or solder connection for DJI Air Units and has a built-in 16MB Blackbox storage chip for flight data logging.

Power outputs include 9 groups of 5V output (total 1.5A), 2 groups of 9V output (total 3A) with PINIO remote on/off control, 1 group of 3.3V output, and 3 groups of 4.5V output (max 1A) for peripherals like receivers and GPS modules. It supports 8 motor outputs (M1-M4 on bottom, M5-M8 on front) and multiple UARTs for various peripherals.

SpeedyBee BLS 55A 4-in-1 ESC

The BLS 55A 4-in-1 ESC is designed for 3-6S LiPo input, providing a continuous current of 55A per channel (220A total) and a burst current of 70A (280A total) for 10 seconds. It features a built-in TVS protective diode for surge protection and includes a 1000uF Low ESR Capacitor in the package for enhanced stability. The ESC supports DSHOT300/600 protocols and current sensing (Scale=400, Offset=0). It also supports ESC Telemetry.

ESC Protection Features — The ESC includes a TVS Protective Diode, 21 onboard TDK capacitors, and supports an external 1000uF high-capacity electrolytic capacitor for upgraded protection against voltage spikes and interference.

5. Asennus

Asennus

The SpeedyBee F405 V5 FC and BLS 55A ESC both feature 30.5 x 30.5mm mounting holes with a 4mm hole diameter. They are designed to be stacked together using the provided silicone grommets and screws.

FC and ESC Installation Methods — Diagram illustrating soldering, direct plug, standard, and reverse installation methods for the FC and ESC. When fixing the stack, use M3 black silicone washers to ensure sufficient space between the flight controller and the ESC.

Connecting the FC and ESC

The FC and ESC can be connected via a 10-pin connector or by direct soldering. The 10-pin design provides enhanced safety redundancy.

FC and ESC Connection with Motors — Connection diagram for the FC and ESC with motors, including the 1000uF Solid Capacitor and XT60 Power Cable. It is strongly recommended to use the included 1000uF solid capacitor to protect the AIO flight controller from instantaneous voltagpiikkejä, kun virta kytketään.

6. Kytkentäkaaviot

Kattava kytkentäkaavio

Comprehensive Wiring Diagram for SpeedyBee F405 V5 Stack — Detailed wiring diagram showing connections for various components including Spektrum, ELRS, PPM, SBUS, and Crossfire Nano receivers, LED strips, Servo, Buzzer, GPS, Analog VTX, and DJI Air Unit.

DJI Air -yksikön liitäntä

DJI Air Unit Connection Diagrams — Diagrams for connecting the FC to DJI O3 Air Unit, RunCam Link/Caddx Vista Air Unit, and DJI Air Unit V1 using the 6-pin cable.

Receiver Specific Notices

SBUS Receiver Importance Notice — Importance notice for SBUS receiver: When using an SBUS receiver, the SBUS signal wire must be connected to the SBUS pad on the front side of the flight controller (this pad internally uses UART2). If also using a DJI Air Unit (O3/Link/Vista/Air Unit V1), you must disconnect the SBUS signal wire from the Air Unit harness. Failure to do so will prevent the SBUS receiver from being properly recognized by the flight controller. Use tweezers to pick out the SBUS wire from the 6-pin harness connector (or directly cut this wire) and insulate the exposed part of the wire carefully.

ELRS Receiver Importance Notice — Importance notice for ELRS receiver: We recommend connecting the ELRS receiver's TX and RX to the T2 and R2 pads on the flight controller. However, when using the DJI Air Unit simultaneously, some ELRS receivers may not be recognized properly by the flight controller. If you encounter this issue, you need to disconnect the SBUS signal wire from the Air Unit harness. You can use tweezers to pick out the SBUS wire from the 6-pin harness connector (or directly cut this wire) and insulate the exposed part of the wire carefully.

7 Kokoonpano

Wireless Tuning via SpeedyBee App

Configure FC and ESC via Bluetooth — The SpeedyBee app allows you to configure your FC and ESC via Bluetooth, enabling wireless tuning and firmware updates.

The SpeedyBee F405 V5 FC supports full-featured Bluetooth tuning. Connect to the SpeedyBee App on your smartphone to flash FC firmware, tune parameters, and configure your quad anytime, anywhere. Ensure MSP is enabled with Baud rate 115200 on UART4 for Bluetooth connection.

Moottorin suunnanvaihto

You can change motor directions wirelessly using the SpeedyBee app. Connect to the app, navigate to 'Motors' and then 'Motor Direction Settings' to adjust as needed.

LED-nauhan ohjaus

LED Pads with Simple Switching — Diagram showing the FC with four sets of LED pads, allowing for simple switching of LED presets. LED strips could be purchased separately. Long press the boot button to switch to Betaflight LED mode.

The FC supports 4 sets of LED pads. When the FC is powered on and in standby mode, the BOOT button can be used to control the LED strips connected to LED1-LED4 connectors on the bottom side. Short-press the BOOT button to cycle through different LED displaying modes. Long-press the BOOT button to switch between SpeedyBee-LED mode and BF-LED mode. In BF-LED mode, all LED1-LED4 strips will be controlled by Betaflight firmware.

8. Käyttöohjeet

Once installed and configured, your SpeedyBee F405 V5 Stack is ready for flight. Ensure your radio transmitter is properly bound and configured with your receiver. Always perform pre-flight checks, including propeller security, battery level, and control surface response, before each flight.

Virta päälle: Connect your LiPo battery to the XT60 connector. The FC and ESC will initialize.
Viritys: Arm your drone using your configured arming switch on your radio transmitter.
Lento: Operate your drone according to standard FPV flight practices.
Asetuksen poistaminen: Disarm your drone using your configured disarming switch after landing.

9. Vianmääritys

Flight Controller Not Responding / Bricked

If your FC becomes unresponsive or appears 'bricked', you can force it into DFU (Device Firmware Upgrade) mode for firmware flashing:

Press and hold the BOOT button on the FC.
While holding the BOOT button, connect the FC to your computer via the USB Type-C cable.
The FC should now be in DFU mode, allowing you to flash new firmware using Betaflight Configurator.

SD Card Compatibility Issues

SD Card Compatibility Information — Information regarding SD card compatibility for the F405 V5 Flight Controller. The F405 V5 FC supports Standard (SDSC) or High Capacity (SDHC) microSD cards under 32GB. Extended capacity cards (SDXC) are not supported. Cards must be formatted with FAT16 or FAT32. Betaflight can only recognize a maximum of 4GB.

Betaflight firmware requires the microSD card to be either Standard (SDSC) or High Capacity (SDHC) and under 32GB. Extended Capacity cards (SDXC) are not supported. The microSD card MUST be formatted with the FAT16 or FAT32 (recommended) format. While you can use any SD card less than 32GB, Betaflight can only recognize a maximum of 4GB. It is recommended to use a 3rd party formatting tool and choose 'Overwrite format' when formatting your card.

10. Tekniset tiedot

SpeedyBee F405 V5 30.5 × 30.5 mm pienoismallin lennonohjain

Ominaisuus	Erittely
MCU	STM32F405
IMU (gyroskooppi)	ICM42688P
USB-portin tyyppi	Uusi Type-C-liitäntä
Barometri	SPA06-003
OSD-siru	AT7456E
Täysin varusteltu Bluetooth-viritys	Tuettu. Yhdistä SpeedyBee-sovelluksen kautta FC:n laiteohjelmiston päivitystä ja parametrien säätöä varten.
Langattoman FC:n laiteohjelmistopäivitys	Tuettu
DJI Air -yksikön liitäntä	Tukee 6-nastaista suoraa pistoke- tai juotosliitäntää
Blackbox	Tuettu, sisäänrakennettu 16 Mt:n tallennuspiiri
Tulo Voltage	3-6S LiPo akku
Itsenäinen 5 V BEC-lähtö	9 ryhmää (4 × +5 V:n liitäntää edessä, 1 × BZ+ summeriliitäntä ja 4 × +5 V:n liitäntää kulmissa ulkoisia LEDejä varten). Kokonaislähtövirta: 1.5 A.
Itsenäinen 9 V BEC-lähtö	2 ryhmää (1 x 9 V:n liitäntä edessä, 1 x 9 V:n lähtö liittimessä takana). Kokonaislähtövirta: 3 A. Tukee PINIO-etäkäyttöä päälle/pois.
MCU ja gyroskooppivirta	Itsenäinen LDO
3.3V lähtö	1 ryhmä (1 × 3.3 V pad edessä)
4.5V lähtö	3 ryhmää (3 × 4.5 V:n liitäntäpadit edessä). Voi syöttää virran vastaanottimelle ja GPS:lle, kun FC:tä käytetään USB:n kautta. Suurin lähtövirta: 1 A.
ESC-signaali	M1-M4-liitäntätyynyt ja 10-nastainen liitin takana
Servosignaali	S5-S6-pehmusteet edessä
ESC-telemetriatulo	Tuettu (UART5)
Betaflight-kameran virityspad	Tuettu (CC-levy edessä)
I2C	Tuettu (GPS-liitin + tyynyt)
UART	UART1 (Bluetooth); UART2 (vastaanottimen etulevyn kosketuslevyt); UART3 (DJI VTX -kosketuslevyt + takaosan SH1.0-6-pinninen liitin); UART4 (GPS-kosketuslevyt + etuosan SH1.0-6-pinninen liitin); UART5 (TLM); UART6 (vastaanottimen kosketuslevyt + takaosan SH1.0-4-pinninen liitin)
ST LED -tyynyt	Tuettu etupaneelin G/5V/LED-kosketuslevyillä; ohjataan FC-laiteohjelmistolla
Meteor LED -nauhatyynyt	Tuettu. Vaihda SB-LED- ja ST-LED-tilojen välillä BOOT-painikkeella tai sovelluksella. SB-LED-tilassa ohjaus tapahtuu ESP32 Bluetooth -sirun avulla.
Summerityynyt	Tuettu
BOOT-painike	[A] Pidä BOOT-painiketta painettuna käynnistyksen aikana pakottaaksesi DFU-tilan vilkkumaan. [B] Virran ollessa päällä ja valmiustilassa lyhyt painallus vaihtaa LED-näyttötilaa; pitkä painallus vaihtaa SB-LED/ST-LED-tilaa. ST-LED-tilassa LED1–LED4-tiloja ohjaa FC-laiteohjelmisto.
RSSI-tyynyt	Tuettu
SmartPort	Ei tuettu
Tuettu FC-laiteohjelmisto	Betaflight, INAV, Ardupilot
Laiteohjelmiston kohdenimi	SPEEDYBEEF405V5
Tehdasohjelmistoversio	Betaflight 4.5.2
Konfiguraattorin versio	Betaflight 10.10.0
Asennusreiät	30.5 × 30.5 mm (Ø4 mm), sivulle avautuva
Mitat	39 mm (P) × 39 mm (L) × 4.9 mm (K)
Paino	8.1 g

SpeedyBee OX32 55A 30.5×30.5 4-in-1 ESC

Ominaisuus	Erittely
Oletuslaiteohjelmisto	OX32
Jatkuva virta	55 A (kanavaa kohden) / 220 A (4-in-1)
Maksimivirta	70 A (kanavaa kohden) / 280 A (4-in-1)
TVS-suojadiodi	Kyllä (sisäänrakennettu)
Ulkoinen kondensaattori	1000µF kiinteä kondensaattori (sisältyy pakkaukseen)
ESC/moottoriprotokolla	DSHOT300/600
Tulo Voltage	3-6S LiPo
Teholähtö	VBAT
Virta-anturi	Tuettu
ESC-telemetria	Tuettu
Asennusreiät	30.5 × 30.5 mm (Ø4 mm), sivulle avautuva
Mitat	40.9 mm (P) × 44.9 mm (L) × 8.0 mm (K) (jäähdytyselementin kanssa)
Paino	19.1 g
Virtamittarin huomautus	Tuettu (skaala=27, siirtymä=-2644)

SpeedyBee F405 V5 Stack Dimensions — Dimensions of the assembled SpeedyBee F405 V5 Stack.

11. Käyttäjävinkkejä

Langaton käyttömukavuus: Ota täysi etutage of the SpeedyBee app's wireless tuning capabilities. This eliminates the need for a laptop in the field for minor adjustments or quick checks.
Capacitor is Key: Always install the included low ESR capacitor. It's crucial for protecting your flight controller from voltage spikes, especially during aggressive maneuvers or power-intensive operations.
SD-kortin alustus: If you experience issues with Blackbox logging, double-check your microSD card's format (FAT16/FAT32) and ensure it's an SDSC or SDHC type under 32GB. Reformatting with an 'Overwrite format' option can often resolve problems.
Vastaanottimen johdotus: Pay close attention to the specific wiring instructions for SBUS and ELRS receivers, especially when integrating with DJI Air Units, to avoid recognition issues.

12. Takuu ja tuki

For warranty claims, technical support, or further assistance, please contact your retailer or the manufacturer directly. Keep your proof of purchase for any warranty-related inquiries. Always refer to the official SpeedyBee website for the latest firmware updates and support resources.