Repeater

ENGO CONTROLS logo

ZigBee network repeater

ENGO CONTROLS EREPEATERZB ZigBee Network Repeater A1

ENGO CONTROLS EREPEATERZB ZigBee Network Repeater A2

ENGO CONTROLS EREPEATERZB ZigBee Network Repeater A3

EREPEATERZB

Quick Guide

Ver. 1
Release date: III 2023

INTRODUCTION:

Repeater increases wireless network signal range for all Engo devices which works over ZigBee 3.0 protocol. It helps to improve radio signal range in places, where wireless network is disturbed by distance or other obstacles (concrete walls, reinforced ceilings, etc.). This device cannot operate standalone. IIn order to use it EGATEZB ZigBee 3.0 gateway is needed.

Red warning WARNING:
This product must be used with EGATEZB ZigBee 3.0 gateway (purchased separately).

PRODUCT COMPLIANCE:
This product complies with the following EU Directives:
2014/30/EU, 2014/35/EU, 2014/53/EU, 2011/65/EU.

SAFETY INFORMATION:
Use in accordance with national and EU regulations. Use the device only as intended, keeping it in a dry condition. The product is for indoor use only. Please read the entire manual, before installation or use.

Red warning WARNING:
For the entire installation, there may be additional protection requirements, which the installer is responsible for.

Technical specification:
Power supply 230 V AC 50 Hz
Communication Zig Bee 3.0 2,4 GHz
Dimensions [mm] 40 x 24 x 82
LED diode indications
EXPLANATION 
LED diode flashes blue The device is in pairing mode with ZigBee network (when device didn’t previously added to the ZigBee 3.0 network, or after recovery factory reset)
LED diode lights up blue The device has been added to the ZigBee 3.0 network
LED diode is off Repeater is not connected to power supply 230V
Installation of the repeater in the app

Make sure your router is within range of your smartphone. Make sure you are connected to the Internet. This will reduce the pairing time of the device.

STEP 1 – DOWNLOAD ENGO SMART APP

Download the ENGO Smart app from Google Play or Apple App Store and install it on your smartphone.

Google Play                                   App Store

ENGO CONTROLS EREPEATERZB ZigBee Network Repeater QR1 Engo Smart ENGO CONTROLS EREPEATERZB ZigBee Network Repeater QR2

STEP 2 – REGISTER THE NEW ACCOUNT

To register a new account, please follow the steps below:

ENGO CONTROLS EREPEATERZB ZigBee Network Repeater B1
To register a new account, please follow the steps below:

ENGO CONTROLS EREPEATERZB ZigBee Network Repeater B2
Then set the login password.

ENGO CONTROLS EREPEATERZB ZigBee Network Repeater B3
Enter the verification code received in the email. Remember that you only have 60 seconds to enter the code!

ENGO CONTROLS EREPEATERZB ZigBee Network Repeater B4
Enter your e-mail address to which the verification code will be sent.

STEP 3 – INSTALLATION OF THE ZigBee 3.0 REPEATER IN THE APP

After installing the app and creating an account:

ENGO CONTROLS EREPEATERZB ZigBee Network Repeater C1
Make sure you have added ZigBee gateway to app

ENGO CONTROLS EREPEATERZB ZigBee Network Repeater C2
Make sure the repeater is connected to power supply. The blue LED should flash. If not, perform factory reset (check „Factory reset” section).

ENGO CONTROLS EREPEATERZB ZigBee Network Repeater C3
In the app, select: „Add Device”.

ENGO CONTROLS EREPEATERZB ZigBee Network Repeater C4
Once the ZigBee gateway will search correctly the repeater click „Add”.

ENGO CONTROLS EREPEATERZB ZigBee Network Repeater C5
Name device and click „Done”.

ENGO CONTROLS EREPEATERZB ZigBee Network Repeater C6
The repeater is installed. Blue LED diode is steady and app shows main interface.

Factory Reset (entering the pairing mode)

ENGO CONTROLS EREPEATERZB ZigBee Network Repeater C7Unplug and plug again the repeater three times at intervals of 3 seconds. The LED on the device will flash, which means repeater has been removed from the ZigBee network and gateway. After that repeater will enter pairing mode automatically. You can add it back to the ZigBee network (check „STEP 3” section).

ENGO CONTROLS EREPEATERZB ZigBee Network Repeater A4

Producer:
Engo Controls S.C.
43-200 Pszczyna
3E Górnośląska St.
Poland

Distributor:
QL CONTROLS Sp z o.o. Sp. k.
43-262 Kobielice
4 Rolna St.
Poland

www.engocontrols.com

Documents / Resources

ENGO CONTROLS EREPEATERZB ZigBee Network Repeater [pdf] Instruction Manual
EREPEATERZB ZigBee Network Repeater, EREPEATERZB, ZigBee Network Repeater, Network Repeater, Repeater

References

Leave a comment

Your email address will not be published. Required fields are marked *