Contents hide
1 ENFORCER SD-7113-GSP Request Exit Plate with Pneumatic Timer
2 Specifications
3 Product Usage Instructions
4 FAQ
5 Parts List
6 Specifications
7 Overview
8 Installation
9 Adjusting the Timer
10 WARRANTY
11 CONTACT
12 Documents / Resources
12.1 References
13 Related Posts

ENFORCER-LOGO

ENFORCER SD-7113-GSP Request Exit Plate with Pneumatic Timer

ENFORCER-SD-7113-GSP-Request-Exit-Plate-with-Pneumatic-Timer -PRODUCT

Specifications

  • Model: SD-7113-GSP, SD-7113-RSP, SD-7183-GSP, SD-7213-GSP, SD-7213-RSP, SD-7283-RSP
  • Faceplate: Slimline, brushed stainless steel  Single-gang brushed stainless steel
  • Mushroom Size cap button Color: Green Standard, Red, Green Large Red
  • Timer: Pneumatic: 1~60 seconds*
  • Switching capacity: 5A@125VAC
  • Wiring: Red White – 2x N.C. #18 AWG 9 (230mm) for fail-safe, 2x N.O. #18 AWG 9 (230mm) for fail-secure
  • Destructive attack level: Level I
  • Line security: Level I
  • Endurance level: Level I
  • Standby power: Level I
  • Operating temperature:
  • Dimensions: Slimline – 1 1/2 x 4 1/2 x 3 1/2 in (38 x 115 x 88 mm), Single-gang – 2 3/4 x 4 1/2 x 3 1/2 in (70 x 115 x 88 mm)

Product Usage Instructions

  • Find a suitable location for the pneumatic request-to-exit plate.
  • The pneumatic request-to-exit plate can be either surface-mounted or flush-mounted.
  • Wire the request-to-exit plate as described below in Wiring.
  • Adjust the timer as described below in Adjusting the Timer.
  • Test the function of the exit plate and timer, as well as the timer delay.
  • For N.C. operation (fail-safe), connect the red wires to the electronic lock or other device.
  • For N.O. operation (fail-secure), connect the white wires to the electronic lock or other device.

NOTE: Use only low-voltage, power-limited/Class 2 power supply, and low-voltage field wiring not to exceed 98.5ft (30m).

FAQ

  • Q: Can the timer be adjusted for more than 60 seconds?
  • A: No, the timer is adjustable for a range of 1 to 60 seconds only.
  • Q: Is the faceplate weatherproof?
  • A: The faceplate is made of stainless steel but is not specifically designed to be weatherproof. It is recommended to install in indoor locations.

Model

Model Faceplate Message Pushbutton
SD-7113-GSP* Slimline plate Exit / Salida Green mushroom
SD-7113-RSP* Slimline plate Exit / Salida Red mushroom
SD-7183-GSP* Slimline plate Push to Exit Green mushroom
SD-7213-GSP* Single-gang plate Exit / Salida Green mushroom
SD-7213-RSP Single-gang plate Exit / Salida Red mushroom
SD-7283-RSP* Single-gang plate Push to Exit Large red mushroom

The ENFORCER SD-7xx3-xSP series Request-to-Exit Plates with Pneumatic Timer are ideal when providing power to a timer is inconvenient, hazardous, or not conforming with local ordinances and codes. Adjusting the time is easy via a timing screw and can be performed on the spot without tools.

  • Conforms to NFPA 101 Fire Codes for non-electrical breaking of contact
  • Functions entirely without electricity
  • Excellent for installations where supplying additional timer power is inconvenient
  • Reliable US-made pneumatic components
  • Stainless steel single-gang faceplate
  • English and Spanish printed on the faceplate (except SD-7183-GSP, SD-7283-RSP)
  • Timer adjustable for 1~60 seconds

Parts List

  • 1x Request-to-exit plate
  • 2x Faceplate screws
  • 1x Manual

Specifications

ENFORCER-SD-7113-GSP-Request-Exit-Plate-with-Pneumatic-Timer -FIG-1

Overview

ENFORCER-SD-7113-GSP-Request-Exit-Plate-with-Pneumatic-Timer -FIG-2

Installation

  1. Find a suitable location for the pneumatic request-to-exit plate.
  2. The pneumatic request-to-exit plate can be either surface-mounted or flush-mounted.
  3. Wire the request-to-exit plate as described below in Wiring.
  4. Adjust the timer as described below in Adjusting the Timer.
  5. Test the function of the exit plate and timer, as well as the timer delay.

Wiring

  1. For N.C. operation (fail-safe), connect the red wires to the electronic lock or other device.
  2. For N.O. operation (fail-secure), connect the white wires to the electronic lock or other device.
    NOTE: Use only low-voltage, power-limited/Class 2 power supply and low-voltage field wiring not to exceed 98.5ft (30m).

Adjusting the Timer

ENFORCER-SD-7113-GSP-Request-Exit-Plate-with-Pneumatic-Timer -FIG-3

  1. Locate the timing screw as shown in the figure to the right.
  2. Gently rotate the timing screw to:
    1. To increase the delay, turn the screw clockwise.
    2. To decrease the delay, turn the screw counterclockwise.
      NOTE: Do not overtighten or over-loosen the timing screw. If the screw becomes very loose, retighten it until it feels secure.
  3. The minimum delay time is approximately 1 second, and the  maximum delay time is approximately 60 seconds. Use a stopwatch to adjust the time to suit the application.

Sample Applications
Installation with a Maglock and Access Control System

ENFORCER-SD-7113-GSP-Request-Exit-Plate-with-Pneumatic-Timer -FIG-4ENFORCER-SD-7113-GSP-Request-Exit-Plate-with-Pneumatic-Timer -FIG-5

IMPORTANT WARNING: Incorrect mounting which leads to exposure to rain or moisture inside the enclosure could cause a dangerous electric shock, damage the device, and void the warranty. Users and installers are responsible for ensuring that this product is properly installed and sealed

IMPORTANT: Users and installers of this product are responsible for ensuring that the installation and configuration of this product comply with all national, state, and local laws and codes. SECO-LARM will not be held responsible for the use of this product in violation of any current laws or codes.

California Proposition 65 Warning: These products may contain chemicals which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov

WARRANTY

This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for one (1) year from the date of sale to the original customer. SECO-LARM’s obligation is limited to the repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM. This Warranty is void if the damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration, improper
or abnormal usage, or faulty installation, or if, for any other reason, SECO-LARM determines that such equipment is not operating properly as a result of causes other than defects in material and workmanship. The sole obligation of SECO-LARM and the purchaser’s exclusive remedy shall be limited to the replacement or repair only, at SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property damage of any
kind to the purchaser or anyone else.

NOTICE: The SECO-LARM policy is one of continual development and improvement. For that reason, SECO-LARM reserves the right to change specifications without notice. SECO-LARM is also not responsible for misprints. All trademarks are the property of SECO-LARM U.S.A., Inc. or their respective owners. Copyright © 2023 SECO-LARM U.S.A., Inc. All rights reserved.

CONTACT

Documents / Resources

ENFORCER SD-7113-GSP Request Exit Plate with Pneumatic Timer [pdf] Instruction Manual
SD-7113-GSP, SD-7113-RSP, SD-7183-GSP, SD-7213-GSP, SD-7213-RSP, SD-7283-RSP, SD-7113-GSP Request Exit Plate with Pneumatic Timer, SD-7113-GSP, Request Exit Plate with Pneumatic Timer, Plate with Pneumatic Timer, Pneumatic Timer, Timer

References

Related Posts

Leave a comment

Your email address will not be published. Required fields are marked *