EliteControl CTBRCB03JM03-PC Lighting Controller

Product Information:

• Product Name: CTBRCB03JM03-PC Lighting Controller
• Output Wattage: 600W Max
• Universal Voltage: 120-277VAC
• Dimming Controller Type: 0-10Vdc Type / Channels
• RF Communication Type: 1/2 Knockout Mount IP66
• Input Surge Protection: Yes
• Overall Size: Not specified
• Weight: 15 lbs
• Sound Rating: Not specified
• Service Life: Not specified
• Warranty: Not specified

Product Usage Instructions:

• Step 1: Check the input voltage and frequency. The input voltage should be in the range of 120-277VAC with a frequency of 50-60Hz.
• Step 2: Connect the input wires to the power source. The input current should not exceed 5A.
• Step 3: Connect the output wires to the luminaire. The maximum load should not exceed 600W.
• Step 4: Install the lighting controller using the mounting type suitable for your application.
• Step 5: Connect the dimming controller and RF communication type according to your requirements.
• Step 6: Ensure input surge protection is in place.
• Step 7: Turn on the power source and operate the device as per your requirements.
  Note: Always refer to the product manual for detailed instructions and safety precautions before using the device.

Lighting Controller

• Output Wattage: 600W Max.
• Universal Voltage (120-277VAC)
• 0-10V Luminaire
• 1/2” Knockout Mount
• IP66
• FCC ID : 2AJ9LCTRCB0XJM0XXXX

General Specifications

Fulham’s EliteBlue commissioning app can be found on the Apple app store by searching “EliteBlue”. For web app, please visit https://eliteblue.fulham.com
Complete commissioning manual can be found at:
https://www.fulham.com/PDFs/eliteBlue-commissioning-manual.pdf

Power Metering Accuracy

Category	Parameters	Unit (range)	Resolu on/ Accuracy Devia on (%)	Data erasable
Power Metering- Grid Side	Maximum AC Mains Voltage	V (108-305V)	2%	Y
	AC Mains Voltage	V (108-305V)	2%	/
	AC Mains Current	mA (80-5000) mA	2%	/
	Frequency	Hz (50 – 60)	2%	/
	Power Factor	(0 – 1) step 0.01	2%	/
	Input Power	W (10-600)	2%	/
	Apparent Power	W (10-600)	4%	/
	Lifetime Input Energy	Wh (0 – 429496729.3)	2%	N
	Resettable Energy	Wh (0 – 429496729.3)	2%	Y
	Lifetime Apparent Energy	Wh (0 – 429496729.3)	4%	N
	Resettable Apparent Energy	Wh (0 – 429496729.3)	4%	Y
	Average Mains Voltage	V (0-310)	2%	Y
	Average Mains Current (mA)	mA (0 – 15000)	2%	Y
	Average Frequency	Hz (0 – 60)	2%	Y
Diagnos c – Bridge	Bridge Operating Time	hrs (0 – 1193046)	4%	N
	Bridge Load On/Off Cycle	Counter (0 – 16777213)	4%	N
	Bridge Temperature	°C (0°C – +90°C)	5%	/
	Bridge Temperature w/Hours	°C (0°C – +90°C)	5%	N

Mechanical Data

Mount screw: #10-24*1 inch
Mounting hole for threaded pipe: 7/8” (22mm)

Notes:

1. Driver has two (2) mounting tabs with a round hole in each.
2. Fasten a screw through the mounting tab if mounted on a flat surface.
   

   Overall Dimensions
   Length	5.17” [131.5mm]
   Width	2.26 ” [57.6 mm]
   Height	1.29 ” [33mm]
   Wire Length
   AC Input (White/Black)	12.4” [315mm]
   LED Output (Red/Black)	12.4” [315mm]
   Control 0-10V (Pink/Purple/ Orange)	12.4” [315 mm]
   RJ12	17.3” [440 mm]
   Ground (Green/Yelow)	12.4” [315 mm]

    

Wiring Diagram

Color Tuning Wiring

Non Color Tuning Wiring

Notes:
Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction.

FCC Caution

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received,including interference that may cause undesired operation.
   Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Restoring Factory Settings

• To reset the unit you will need to place and hold a magnet for 10 seconds on the reset icon   on the location of the unit shown in the image below.
• Once the magnet has been placed the Indicator Light will stay lit and begin to flash until it shuts off indicating that the unit has been successfully reset.
  • Remove the magnet from the unit, the Indicator Light will light up and flash repeatedly
  • The unit is now ready to be provisioned.

SPECIFICATION INSTRUCTIONS

Part Number Matrix

Product Image: LED Driver

 

Packaging

Master Carton

OUTER DIMENSION
L		W		H
18.26”(464mm)		14.33”(364mm)		7.48”(190mm)
Net Weight	Gross Weight		QUANTITY
23.14 lbs. (10.5kg)	24.69lbs. (11.2 kg)		30pcs.

Fulham co. Inc.: 12705 South Van Ness Ave., Hawthorne, CA 90250 Tel.: 1-323-779-2980 Fax.: 1-323-754-9060. order@fulham.com www.fulham.com
Specifications subject to change without notice.

Documents / Resources

EliteControl CTBRCB03JM03-PC Lighting Controller [pdf] Instructions CTBRCB03JM03-PC Lighting Controller, CTBRCB03JM03-PC, Lighting Controller, Controller

References

• User Manual