EKSAtelecom EKSA H6 Wireless Headset User Manual

EKSAtelecom EKSA H6 Wireless Headset

Specifications

• Brand: EKSA
• Product: EKSA H6 Headset
• Model: H6
• Headset Bluetooth Version: 5.0
• Adapter Bluetooth Version: 5.2
• Effective Wireless Range: 10 m / 32 ft
• Speaker Diameter: 40 mm
• Impedance: 32 Ω ± 15%
• Sensitivity: 114 ± 3 dB
• Frequency Response: 20 Hz – 20 kHz
• Battery Type: Portable Lithium-ion Polymer Battery. Battery Specifications: DC 3.7 V, 500 mAh, 1.85 Wh
• Music Time: ≈55 hours (70% volume)
• Talk Time: ≈30 hours (70% volume)
• Input: 5 V 1 A
• Charging Time: ≈1.5 hours
• Charging temperature range: 0°C-45°C; Discharging temperature range: -20°C-60°C; Operating Frequency: 2402 – 2480 MHz; Maximum Transmit Power: <20 dBm
• Battery Weight: 10.7 g
• Size: 2.7 mm * 1.85 mm; Sensitivity: -25 ± 1 dB
• Frequency Response: 100 Hz – 10 kHz
• Operating Frequency: 2402 MHz- 2480 MHz
• Maximum Transmit Powe: 3.68 mW(5.66 dBm)
• Impedance: 2.2 kΩ
• Polar Pattern: Omnidirectional
• Mic: EKSAtelecom VoicePure Technology

Product Overview

1. Call Indicator
2. EKSAtelecom VoicePure Technology
3. Bluetooth & Charging Indicator
4. Type-C Charging Port
5. Busy Light
6. Volume + / next track
7. Multi-Function Button (MFB)
8. Volume – / previous track
9. EKSA PC Adapter

Operation Guide

Multi-Function Button:

Press for 3 seconds: Headphone on/off.

Click: Play/Pause

Busy Light:

Click: Do-Not-Disturb Mode on/off

Triple-click: Voice Assistant/Siri

Volume Button:

Click: Volume + / –

Press for 2 seconds to 2″ next/previous track

Swivel-to-Mute Microphone:

Swivel upwards: Mute On

Swivel downwards: Mute Off.

Call Functions

Call Handling:

Redial:

Audio Switching:

Press for 2 seconds: During a call, you can switch your audio device.

Three-Way Calling:

 Switch between two calls

Bluetooth Pairing

1. Turn on EKSAtelecom H, until its Bluetooth indicator flashes alternately between red and blue, indicating that the headset is in pairing mode.
2. Turn on the Bluetooth of your device, activate the search feature, and select “EKSA-H6”. After pairing, the Bluetooth indicator flashes slowly in blue light with a voice prompt, “Your headset is connected”, confirming a successful connection.
   • Note:
   • Keep the distance between the EKSA-H6 and your device within 1 meter.
   • If necessary, the PIN code to complete pairing is “0000”.
   • While in pairing state, if a connection cannot be established within 10 minutes, the headset will turn off automatically.
   • When the headset is turned on again, it will connect to the last connected device automatically.
3. To connect to a new device, turn off the Bluetooth of the currently paired device and follow the above steps to connect successfully to a new device.

Bluetooth Pairing

PC: If you want to connect the headset to a PC, you can use the EKSA PC adapter provided in the package. Then, you can enjoy the call function and compatibility with third-party software of the PC. Follow the steps below to get it done.

• Plug the EKSA PC adapter into your PC’s USB port. The adapter will turn on automatically, with the name of “EKSA PC Adapter” displayed on your computer.

USB-A interface

Type-C interface

• When enabled, the indicator on the EKSA PC adapter will flash a blue light, which indicates that it is in pairing mode. Then, put the headset in pairing mode and place it as close to the EKSA PC adapter as possible (within 8 inches). The headset will automatically cally connect to the EKSA PC adapter.
  Note: It takes about 20 seconds to establish a connection between the headset and a PC for the first time. If the connection is unsuccessful, please unplug the adapter and plug it back into the PC. Then restart the headset’s pairing mode and reconnect to your computer.
• USB-A interface
• Type-C interface
• After the headset is successfully connected, the Bluetooth indicator on the headset will slowly flash blue, while the EKSA PC adapter’s indicator will always be blue.

Dual Pairing

1. After successfully connecting the EKSAtelecom H6 to device A,turn off the Bluetooth of device A. The headset’s Bluetooth indicator flashes in red and blue alternately to signify pairing mode.
2. Turn on the Bluetooth of device B, activate search mode, and connect to “EKSA-H6”.
3. Turn on the Bluetooth of device A to connect with “EKSA-H6”. This puts both devices A and B in a simultaneous connection with “EKSA-H6”.

Reset

• When EKSAtelecom H6 is in connected/pairing mode, press and hold the “volume + ” and “volume – ” buttons simultaneously for 6 seconds until the LED lights up in red and blue, indicating the pairing information is cleared.

Charging

1. When the battery is less than 10%, the headset will give a voice prompt “battery low” every 3 minutes. Please charge it as soon as possible.
2. When the EKSAtelecom H6 is not in use, please charge it at least once every 2 months.
3. Please use the original charging cable for charging. The charging voltage can’t exceed 5 V.

CONTACT SERVICE

GLOBAL: +852 6940 4955 (Mon to Fri 9:00 am-6:30 pm, UTC +8 HKT)
GLOBAL: info@eksatelecom.com
www.eksatelecom.com/pages/warranty

• Manufacturer: YI ZHAO (SHENZHEN) CO., LIMITED
• Add.: 6th Floor, T3 Creative Building, Shenzhen Colorful Huiwei Cultural and Creative Expo City, No. 5010 Baoan Avenue, Caowei Community, Hangcheng Street, Baoan District, Shenzhen, Guangdong, China. Email: info@eksatele.com
• Tel.: +85269404955

Battery Manufacturer: Shenzhen Mitacbattery Technology Co., LTD.

• Add.: 4 Floor, 3 Floor, 1 Floor, 5 Floor 1 Building, No. 47, Kengwei Avenue, Shangwu Community, Shiyan Street, Baoan District, Shenzhen, Guangdong, P.R. China
• C&E Connection E-Commerce (DE) GmbH
• Add.: Zum Linnegraben 20, 65933, Frankfurt am Main, Germany
• Tel.: +4901746508451
• Email: info@ce-connection.de

CHARGING SPEED

• The power delivered by the charger must be between min 0.25 Watts required by the radio equipment and max 2.5 Watts in order to achieve the maximum charging speed.

FCC WARNING

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC RF exposure statement:

• The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

C Caution:

• Radio Standards Specification RSS-Gen, issue 5
• This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: This device may not cause interference.
• This device must accept any interference, including interference that may cause undesired operation of the device.

RF exposure statement:

• The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.