EKSATelecom EKSA H3 Wireless Headset

Overview
The EKSA Telecom H3 is a Bluetooth wireless headset with a rotatable microphone boom, call controls, volume/track buttons, and an LED indicator for power, pairing, and charging status.
Quick Setup & Use
- Power on: Press and hold the Multi-Function Button (MFB) for 3 seconds until the LED indicates pairing (red/blue alternating).
- Bluetooth pairing with a phone: Turn on Bluetooth on your device, search for devices, and select “EKSATelecom -H3”. When connected, the headset voice prompt says “Connected” and the LED flashes blue slowly.
- Basic playback/calls: Press MFB once for Play/Pause audio. Answer a call with MFB once; end a call with MFB once during an active call.
- Volume & track: Press Volume + / Volume – once for volume up/down; press and hold Volume + (2 s) for next track; press and hold Volume – (2 s) for previous track.
- Mute microphone: Press the mute button on the microphone boom once.
- Charge: Connect to a powered USB source using the supplied charging cable. LED is solid red while charging and solid blue when fully charged.
Troubleshooting
- Can’t pair within pairing mode: If no connection is established within 10 minutes while in pairing mode, the headset turns off automatically. Turn it on again and repeat pairing.
- Need to pair with a different device: Turn off Bluetooth on the currently connected device, then repeat the pairing steps with the new device.
- PIN requested during pairing: Enter 0000.
- Low battery: When battery level drops below 10%, the headset plays the voice prompt “Low battery” every 3 minutes. Recharge the headset promptly.
- Reset paired-device history: With the headset powered on, press and hold Volume + and Volume – simultaneously for 6 seconds. The LED illuminates red and blue, confirming the paired device history was cleared.
Preface
Thank you for purchasing our product. This manual provides important information about the product’s features, safety instructions, and usage guidelines. Please read this manual carefully before using the product to ensure safe and proper operation. Keep this manual for future reference. If you have any questions or need further assistance, please visit our customer support page: https://www.alza.cz/contact-and-support
Box Contents
- 1 × EKSATelecom H3 Headset
- 1 × Replaceable PU Ear Cushion
- 1 × Charging Cable
- 1 × User Manual
- 1 × Quick Setup Guide
- 1 × Safety Instructions
Specifications
| Specification | Value |
| Brand | EKSATelecom |
| Product | H3 |
| Model | H3 |
| Bluetooth Version | V5.4 |
| Effective Wireless Range | 30 m |
| Input | 5 V ⎓ 200 mA |
| Battery Specification | DC 3.7 V, 400 mAh, 1.48 Wh |
| Battery Type | Lithium-ion polymer battery |
| Music Playback Time | 65 hours (at 50% volume) |
| Specification | Value |
| Talk Time | 35 hours (at 50% volume) |
| Charging Time | 2.5 hours |
| Charging Temperature Range | 0 °C to 45 °C |
| Operating Frequency | 2402 MHz – 2480 MHz |
| Maximum Transmit Power | < 20 dBm |
| Microphone Sensitivity | -38 dB ± 2 dB |
| Microphone Frequency Range | 100 Hz – 10 kHz |
| Microphone Impedance | 2.2 kΩ |
| Speaker Size | 40 mm |
| Speaker Impedance | 32 Ω |
| Speaker Sensitivity | 115 ± 3 dB |
| Speaker Frequency Range | 20 Hz – 20 kHz |
Product Overview
- Microphone Boom: Features an adjustable headband and a boom arm that rotates up to 270°.
- EKSATelecom ENC Microphone: Positioned at the tip of the microphone boom arm.
- Mute Button: Positioned directly on the outer surface of the microphone boom arm.
- Volume + / Next Track Button: The upper button located on the edge of the earcup.
- Volume – / Previous Track Button: The lower button located on the edge of the earcup.
- USB-C Port: Located on the lower rim of the earcup for battery charging.
- LED Indicator: Positioned on the earcup to signal power, pairing, and charging status.
- Multi-Function Button (MFB): The central button situated on the flat outer face of the earcup.
User Guide
Multi-Function Button (MFB)
- Power on/off: Press and hold for 3 seconds.
- Pairing mode: Press and hold for 6 seconds from the powered-off state.
- Play/Pause audio: Press once.
- Voice assistant: Press three times.
Volume Buttons
- Volume up/down: Press the Volume + or Volume – button once.
- Next track: Press and hold the Volume + button for 2 seconds.
- Previous track: Press and hold the Volume – button for 2 seconds.
Mute Button
- Microphone mute on/off: Press the mute button on the boom arm once.
Call Functions
Basic Call Handling
- Answer a call: Press the Multi-Function Button (MFB) once.
- Reject a call: Press and hold the Multi-Function Button (MFB) for 2 seconds.
- End a call: Press the Multi-Function Button (MFB) once during an active call.
Redial
- Redial last dialled number: Press the Multi-Function Button (MFB) twice whilst connected to a mobile phone.
Three-Way Calling
When on an active call and a second call arrives:
- Answer new call and end current call: Press the MFB once.
- Answer new call and place current call on hold: Press the MFB twice.
- Reject incoming call and continue current call: Press and hold the MFB for 2 seconds.
- Switch between two active calls: Press the MFB twice.
Bluetooth Pairing
Pairing with a Mobile Phone
- Switch on the EKSATelecom H3 by pressing and holding the MFB for 3 seconds until the LED indicator flashes red and blue alternately, signalling that the headset is in pairing mode.
- Enable Bluetooth on your device, start the device search, and select “EKSATelecom -H3”. Once paired, the LED indicator will flash blue slowly, and the voice prompt will state
“Connected”. - To pair with a different device, turn off Bluetooth on the currently connected device, then repeat the pairing steps above with the new device.
Notes:
- Ensure the distance between the EKSATelecom H3 and the host device remains within 1 metre during pairing.
- If prompted for a PIN code during pairing, enter 0000.
- If no connection is established within 10 minutes whilst in pairing mode, the headset will turn off automatically.
- When powered on, the headset automatically reconnects to the most recently connected device.
Multipoint Connection (Dual-Device Pairing)
- Pair and connect the EKSATelecom H3 to Device A as described above, then turn off Bluetooth on Device A. The headset LED indicator will flash red and blue alternately to indicate it has returned to pairing mode.
- Turn on Bluetooth on Device B, search for available devices, and connect to “EKSATelecom -H3” (ensure the headset remains within 1 metre of Device B).
- Turn on Bluetooth on Device A and select “EKSATelecom -H3” to reconnect. Both Device A and Device B will now be connected to the headset simultaneously.
Factory Reset
Whilst the EKSATelecom H3 is powered on (in either connected or pairing mode), press and hold the Volume + and Volume – buttons simultaneously for 6 seconds. The LED indicator will illuminate in red and blue, confirming that the paired device history has been cleared.
Charging
- Connect the headset to a powered USB source using the supplied charging cable (Input: 5 V ⎓ 200 mA; charging power range: min. 0.1 W to max. 1 W; charging time: ≤ 2.5 hours).
LED Indicator Status:
- Solid Red: Battery charging
- Solid Blue: Fully charged
Safety Warnings and Operational Advice:
- When the battery level drops below 10%, the headset will sound the voice prompt “Low battery” every 3 minutes. Recharge the headset promptly.
- If the EKSATelecom H3 is left unused for extended periods, charge the battery at least once every 2 months.
- Only use the supplied charging cable. The charging voltage must not exceed 5 V.
- Do not operate or charge this product in damp or wet environments.
- Battery Safety Warning: This product contains an integrated lithium battery. To prevent the risk of fire or explosion, do not expose the product to excessive heat, direct sunlight, or open flames, and never dispose of it in a fire.
Warranty Conditions
Warranty policies may vary by country or region. For specific details such as the warranty period and coverage, please refer to the after-sales policy provided by the sales channel from which you purchased the product. If you need to request after-sales service, please contact the sales channel or authorized dealer where the product was purchased. Be sure to provide valid proof of purchase, such as an invoice or order number, to confirm your eligibility for service.
EU Declaration of Conformity
This equipment is in compliance with the essential requirements and other relevant provisions of EU directives.
Waste from Electrical and Electronic Equipment (WEEE)
This product must not be disposed of as normal household waste in accordance with the EU Directive on Waste Electrical and Electronic Equipment (WEEE – 2012/19/EU). Instead, it shall be returned to the place of purchase or handed over to a public collection point for the recyclable waste. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. Contact your local authority or the nearest collection point for further details. Improper disposal of this type of waste may result in fines in accordance with national regulations.
Documents / Resources
![]() | EKSA H3 Wireless Headset |
References
- User Manualmanual.tools
