EDIFIER R1280DB Active Speaker User Guide

Box Contents

Note: Images are for illustrative purposes only and may differ from the actual product.

Illustrations

1. Infrared receiver
2. Treble dial
3. Bass dial
4. Master volume control/ input selection
   Press in to navigate between audio sources: LINE1→ LINE2→Optical→Coaxial→Bluetooth.
   Note: Press and hold the master volume control to enter into standby mode.
5. Power indicator
   Red: optical/coaxial inputs
   Blue: Bluetooth input
   Green: Line in1/Line in2 inputs
6. Speaker output
7. Power switch
8. Power cord
9. Line in1 input port
10. Line in2 input port
11. Optical input port
12. Coaxial input port

Remote control

1. Power ON/OFF
2. Mute
3. Volume decrease
4. Volume increase
5. Line in1 input
6. Line in2 input
7. Optical input
8. Coaxial input
9. Bluetooth input (Press and hold to disconnect Bluetooth devices)
10. Pause/play (for Bluetooth only)
11. Previous track (for Bluetooth only)
12. Next track (for Bluetooth only)

Battery loading:
Please refer to the illustration to open the battery compartment, insert the CR2025 battery and close the compartment.

WARNING!

1. Don’t swallow the battery; danger of chemical burn.
2. The product includes a wafer battery. Swallowing this battery may lead to injury or death. Do not place the new or old battery in where children can get to it.
3. Don’t use the product if the battery cover is missing or not closed, and keep the remote inaccessible to children.
4. Please go to the hospital immediately if the battery is swallowed.

Note:

1. Do not place the remote control in places that are hot and humid.
2. Do not charge the batteries.
3. Remove the batteries when unused for a long period of time.
4. The battery should not be exposed to excessive heat such as direct sun, fire or similar.
5. Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.

Connection

1. Connect the speakers with the included speaker connecting cable.
2. Connect to power source, power on the speaker, then the indicator is lit.

Line in mode

1. Press the master volume control on the active speaker or press the “LINE1″/”LINE2” button on the remote control to select LINE IN input. The indicator turns to green.
2. Using audio cable to connect audio source to the speaker.
3. Play from your device and adjust the volume accordingly.

Optical/coaxial mode

1. Press the master volume control on the active speaker or press the “OPT”/”COX” button on the remote control to select the optical/coaxial input. The indicator turns to red.
2. Using optical or coaxial cable (optical cable included) to connect audio sources to your speaker.
3. Play from your devices and adjust the volume accordingly.

Note:

1. In optical and coaxial modes, only PCM signal with 44.1KHz/48KHz can be decoded.

Bluetooth mode

1. Turn on speaker and switch to Bluetooth mode by pressing the Bluetooth button on the remote control or press the master volume control on back panel of the active speaker. The indicator turns to blue.
2. Go to setup section on your source devices (mobile phones, tablets, etc.) and search for nearby Bluetooth devices, you will find “EDIFIER R1280DB” in the list.
3. Pair your device with “EDIFIER R1280DB”.
4. Play audio tracks on your device and adjust the volume to a desired level.
5. To disconnect from the current Bluetooth device, press and hold the ” ” button for 2 seconds.

Note:

1. Bluetooth connectivity and compatibility may be different among different source devices, depending on the software versions of source devices.
2. To enjoy the full Bluetooth functions of this product, please ensure your mobile device supports A2DP and AVRCP profile.
3. PIN code for connection is “0000” if needed.

Specifications

Power output: L/R: 21W+21W
Frequency response: 55Hz-20KHz
Bass unit: 4 inch (116mm)
Tweeter unit: Φ13mm silk dome tweeter

Declaration for EU
Frequency Band: 2.402GHz ~ 2.480GHz
RF Power output: ≤20 dBm (EIRP)
There is no restriction of use.

Troubleshooting

If you want to find out more about EDIFIER, please visit our website at www.edifier.com
For EDIFIER warranty queries, please visit the relevant country page on our www.edifier.com and review the section Warranty Terms.
USA and Canada: service@edifier.ca
South America: Please visit www.edifier.com (English) or www.edifierla.com (Spanish/Portuguese) for local contact information.

Documents / Resources

EDIFIER R1280DB Active Speaker [pdf] User Guide EDF100016, R1280DB Active Speaker, R1280DB, Active Speaker, Speaker

References

• User Manual