V11 Shot Timer
“
Specifications
- Model: Disave Volumetric Touch Pad
- Display: Shot Timer
- Volume Settings: 1RISTRETTO, 1ESPRESSO, 2RISTRETTO, 2ESPRESSO,
MANUAL - Ideal Shot Time: Varies by setting
- Buffer: +/- 3 seconds
Product Usage Instructions
Setting a New Volume
- Ensure the machine is at ideal operating temperature
(approximately 30 minutes after startup). - Load the porta-filter with the appropriate amount of coffee
grounds at the correct grind setting. - Press and hold Button 5 for more than 8 seconds to enter
Volumetric Programming Mode. - When prompted, select the desired button (Buttons 1-4) for
programming. - Measure the desired shot volume and press the selected button
again to set the new volume. - Repeat the process for other buttons if needed.
Numeric Volume/Time Adjusting
Refer to the manual for detailed instructions on adjusting
volume and time settings for each button.
Back-Flush Function
Follow the guidelines in the manual to utilize the back-flush
function for maintenance purposes.
Access the manager level menu as described in the manual for
advanced settings and controls.
FAQ
Q: How do I know if a shot is within tolerance?
A: The display will show a GREEN time if the shot falls within
the ideal extraction time +/- buffer. Otherwise, it will display
RED.
Q: Can I overwrite a previously set volume and time?
A: Yes, you can reprogram a button with a new volume and time
even if the orange light has turned off.
A: Ensure the machine is in programming mode, and try again
within the specified time frame.
“`
09.30
30.0 sec
2Espresso
SHOT TIMER
USER MANUAL
CONTENTS
1. Introduction …………………………………………………………………………. 2
Scope
Overview
Default Settings
2. Setting a New Volume ……………………………………………………………. 3 3. Numeric Volume/Time Adjusting ……………………………………………. 4 4. Back-Flush Function ……………………………………………………………….. 8 5. Manager Level Menu ……………………………………………………………… 9
1. Store Name …………………………………………………………………………………………………. 5 2. Time/Date …………………………………………………………………………………………………… 6 3. Dose Program Lock ……………………………………………………………………………………… 6 4. Volume Buttons ………………………………………………………………………………………….. 7 5. Exit Menu ……………………………………………………………………………………………………. 7
Disavè Shot Timer Manual V11 Sept 2020
pg. 1
INTRODUCTION Scope
The Disave volumetric touch pad has been designed to help the barista maintain quality control of shots during a busy day, by displaying the extraction time of the last shot made. This is reinforced by a simple GREEN and RED coloring on the display to let the barista know the last drink was made either within tolerance, GREEN, or outside of tolerance, RED.
Overview of the buttons 13
5
24
*Throughout the manual references to the buttons will be numbers as outlined above.
Navigating the menus, the below buttons operate the curser to move in 4 directions and Button 5 is the enter key (E).
E
Default Button Settings
Button 1 Button 2 Button 3 Button 4 Button 5
Name 1RISTRETTO 1ESPRESSO 2RISTRETTO 2ESPRESSO MANUAL
Volume Ideal Shot Time
22
22
30
30
44
22
60
30
n/a
n/a
*Volumes and time may not net the same result.
Buffer +/- 3 sec +/- 3 sec +/- 3 sec +/- 3 sec
n/a
Disavè Shot Timer Manual V11 Sept 2020
pg. 2
Setting a new volume
Check the machine is at ideal operating temperature, this should be around 30 minutes after first start up for most models.
Load the porta-filter with the right amount of fresh coffee grounds at the correct grind setting for your coffee roast style.
Press and hold for more than 8 seconds Button 5, the display will read, “Volumetric Programming Mode Press button within 30 seconds” and all the buttons will flash ORANGE. If no button is selected, the programming mode will timeout after 30 seconds and normal operation with resume.
09.30
30.0 sec
2Espresso
8Secs
Insert the porta-filter with the coffee into the group head, select the desired button you wish to program (Buttons 1-4).
Measure out the desired shot volume (ideally with a suitable scale) and then press the same button to stop and set the new volume. The shot time recorded during the volumetric setting for each button is memorized and becomes the new ideal time +/- the buffer value. Repeat the process to program Buttons 1-4 as needed.
Once a button has had a new volume set, the orange light for that button will go out as a reference point to know you have programmed it. A new volume and time can be recorded over a previously set button by following the above steps, even if the orange light has gone out.
Important: Use a porta-filter filled with fresh espresso grounds for every new shot that is programmed.
Example:
Programming Button 2 for 25mls with a total extraction time of 33 seconds with a buffer of +/- 3 seconds, will set the shot alarm to show a GREEN time, if the extraction is made between 30-36 seconds. A shot made less or more of this time will show RED.
Extracting Shot
33sec
2Espresso
Extracting Shot
29 sec
2Espresso
To exit the volumetric setting program at any time, press Button 5.
Disavè Shot Timer Manual V11 Sept 2020
pg. 3
Numeric Volume/Time Adjusting
Volume, Shot Time, Pre-Infusion
09.30
30.0 sec
2Espresso
8Secs
From the on screen, press and hold for more than 8secs Button 5, the display will read, “Volumetric Programming Mode Press button within 30 seconds” and all the buttons will flash ORANGE. Release button. If no button is selected, the programming mode will timeout after 30seconds and normal operation with resume.
Volumetric Programming Mode
Press button within 30 seconds
5Secs
Press and hold button 5 again for 5secs to access Numeric adjustment of the Volume, Shot Time and PreInfusion.
Volume/Time
1. Volume 2. Shot Time 3. Pre Infusion 4. Exit
With the on Volume selection press the E key (B5)
Volume
B1. 1Ristretto B2. 1Espresso B3. 2Ristretto B4. 2Espresso Exit
Disavè Shot Timer Manual V11 Sept 2020
pg. 4
Use the up (B1) and down (B2) keys to move to drink selection to adjust and then press the E key (Button 5)
Volume Adjust
63mls
1Ristretto
Use the up (B1) and down (B2) keys to adjust volume, press the E key (Button 5) to save and exit back one menu to Volume. The operator can then adjust the volume of the other buttons as needed or select the exit to move back to the Volume/Time menu.
Volume/Time 1. Volume 2. Shot Time 3. Pre Infusion 4. Exit
Use down (B2) key to move to Shot Time and then press the E key (B5)
Shot Time
B1. 1Ristretto B2. 1Espresso B3. 2Ristretto B4. 2Espresso Exit
Use the up (B1) and down (B2) keys to move to drink selection and then press the E key (B5)
Shot Time Adjust
22 secs
1Ristretto
Disavè Shot Timer Manual V11 Sept 2020
pg. 5
Use the up (B1) and down (B2) keys to adjust Shot time, press the E key (Button 5) to save and exit back one menu to Shot Time. The operator can then adjust the Shot Time of the other buttons as needed or select the exit to move back to the Volume/Time menu.
Volume/Time
1. Volume 2. Shot Time 3. Pre Infusion 4. Exit
Use down (B2) key to move to Pre-Infusion and then press the E key (B5)
Pre Infusion Menu
Pre Infusion Infuse with Pump
Parameters Exit
OFF YES
With the on the “Pre Infusion” selection, press the E key to switch between on and off to turn pre infusion on or off.
Pre Infusion Menu
Pre Infusion Infuse with Pump
Parameters Exit
OFF YES
Use the down (B2) key to move to “Infuse with Pump” selection and then press the E key (B5) to switch between YES and NO, to use the pump pressure during the infusion volume.
Pre Infusion Menu
Pre Infusion Infuse with Pump
Parameters Exit
OFF YES
Use the down (B2) key to move to “Parameters” selection and then press the E key (B5)
Disavè Shot Timer Manual V11 Sept 2020
pg. 6
Parameters
B1. 1Ristretto B2. 1Espresso B3. 2Ristretto B4. 2Espresso Exit
Use the up (B1) and down (B2) keys to move to drink selection and then press the E key (B5)
P re-I nfusi on Vol um e
15 ml
B1. 1Ristretto
Use the up (B1) and down (B2) keys to adjust pre-infusion volume, press the E key (Button 5) to save and move to Infuse Time.
I nfuse Ti m e
5 s
B1. 1Ristretto
Use the up (B1) and down (B2) keys to adjust infuse time, press the E key (Button 5) to save and exit back one menu to Parameters. The operator can then adjust the Parameters of the other buttons as needed or select the exit to move back to the Pre-Infusion Menu.
Pre Infusion Menu
Pre Infusion Infuse with Pump
Parameters Exit
OFF YES
Addition adjustments can be made by moving or select exit to move back to the Volume/ Time Menu
Disavè Shot Timer Manual V11 Sept 2020
pg. 7
Volume/Time 1. Volume 2. Shot Time 3. Pre Infusion 4. Exit
Addition adjustments can be made by moving or select exit to escape from the menu.
Back-Flush Function
Insert a blind basket into a porta-filter handle. Dose the appropriate amount of backflush powder into the blind basket and insert into the group head to clean. Press simultaneously and hold down for more than 3 seconds Buttons 3+4. The cleaning function will start and display the below message while flashing all button lights green
CLEANING IN PROGRESS DON’T REMOVE GROUP HANDLE TO CANCEL PRESS ANY BUTTON TWICE
The function will cycle 10 times with back-flush powder to clean the group head of old coffee oil, then stop and display the below message with all button lights on solid green.
CLEANING COMPLETE REPEATTO RINSE WITHOUT DETERGENT PRESS ANY BUTTON TO START RINSE
Remove the porta-filter handle and clean out remaining backflush detergent, reinstall porta-filter handle into group head and press any button to start rinse. The button lights will start to flash green again and below message will be displayed.
Disavè Shot Timer Manual V11 Sept 2020
pg. 8
RINSE IN PROGRESS DON’T REMOVE GROUP HANDLE TO CANCEL PRESS ANY BUTTON TWICE
Once rinse cycle is complete the display will show below message. Press any button to exit
RINSE COMPLETE PRESS ANY BUTTON TO EXIT
Press any button to exit
Manager Level Menu
Under the manager level menu, the below parameters can be accessed. 1. Store Name 2. Group Head Position 3. Time/Date 4. Button Labels 5. Volume Buttons 6. Dose Program Lock 7. Shot Timer ON/OFF 8. Shot Time Alarm 9. Transfer Config Exit Menu
To access the menu, press simultaneously and hold for more than 10 seconds, Buttons 2+4
09.30
Manager Level Menu
1.Store Name 2.Group Head Positi on 3. Time/Date 4.Button Labels 5.Volume Buttons
1. Store Name
Disavè Shot Timer Manual V11 Sept 2020
pg. 9
Manager Level Menu
1.Store Name 2.Group Head Positi on 3. Time/Date 4.Button Labels 5.Volume Buttons
It is possible to name the board or give it a position number on a machine for data collection.
Move the cursor to be in line with the Store Name by using B1 or B2 key. Press the E key to enter menu.
Underline is the position you would
like to type
Store Name
D I S AV E
12 3 4 56 7 89 0 QW E R TY UI O P
A SDF G HJK L ZX CV B N M
Use the direction buttons to move the curser to select character or action
A KEYBOARD menu will appear which can have a unique name or number entered up to 10 characters.
Use the direction buttons to move the cursor highlighted in GREEN to add or replace characters above that are underlined by the line highlighted as RED. When the curser is on the character required press the E key to make the change.
Pressing the E key on the symbols will have the below affect
Move the underline back 1 position
Move the underline forward 1 position
Add a blank space
Will exit the menu and return you to the main Manager Level Menu.
2. Group Head Position
09.30
Manager Level Menu
1.Store Name 2.Group Head Positi on 3. Time/Date 4.Button Labels 5.Volume Buttons
It is possible to number the group position the board is installed on for a machine for data collection. Move the cursor to be in line with group head position by using B1 or B2 key. Press the E key to enter menu.
Disavè Shot Timer Manual V11 Sept 2020
pg. 10
Group Head P osi ti on
Group 1
Use the up (B1) and down (B2) keys to adjust group position between Group 1 and Group 4, press the E key (Button 5) to save and exit back to Manager Level Menu.
3. Time/Date
09.30
Manager Level Menu
1.Store Name 2.Group Head Positi on 3. Time/Date 4.Button Labels 5.Volume Buttons
A time and date can be added to the board. Move the cursor to be in line with the time and date by using the UP or DOWN key. Press the E key to enter menu.
Navigate the keyboard with the direction keys in the same manner as outlined above to adjust the date.
Date 01/01/2000 1 2 3 4 5 6 7 8 9 0
Navigate to the to progress to the next menu and then adjust the time in the same matter.
Time 01:30 1 2 3 4 5 6 7 8 9 0
Navigate to the to exit the Time/Date setup and return to the main Manager Level Menu
Disavè Shot Timer Manual V11 Sept 2020
pg. 11
4. Button Labels
09.30
Manager Level Menu
1.Store Name 2.Group Head Positi on 3. Time/Date 4.Button Labels 5.Volume Buttons
Personalise each button with your own label. Move the cursor to be in line with Button Labels selection by using the UP or DOWN key. Press the E key to enter menu.
Change Button
Labels
B1: 1Ristretto
B2: 1Espresso B3: 2Ristretto B4: 2Espresso
B5: Manual Exit
Move the cursor to be inline with label to change. Press the E key.
Underline is the position you would
like to type
1Ristretto
12 3 4 56 7 89 0 QW E R TY UI O P A SDF G HJK L
ZX CV B N M
Use the direction buttons to move the curser to select character or action
A KEYBOARD menu will appear which can have a unique name or number entered up to 10 characters.
Use the direction buttons to move the cursor highlighted in GREEN to add or replace characters above that are underlined by the line highlighted as RED. When the curser is on the character required press the E key to make the change.
Pressing the E key on the symbols will have the below affect
Move the underline back 1 position
Move the underline forward 1 position
Add a blank space
Will exit the menu and return you to the list of button labels. Adjust other labels or select exit to return to the main Manager Level Menu.
Disavè Shot Timer Manual V11 Sept 2020
pg. 12
5. Volume Buttons
09.30
Manager Level Menu
1.Store Name 2.Group Head Positi on 3. Time/Date 4.Button Labels 5.Volume Buttons
It is possible to disable any of the 5 buttons if they are not required.
Move the cursor to be in line with the Volume Button by using the UP or DOWN key. Press the E key to enter menu.
Volume Buttons Enable/Disable
1. BTN 1: DISABLE 2. BTN 2: ENABLE 3. BTN 3: ENABLE 4. BTN 4: ENABLE 5. BTN 5: ENABLE 6. EXIT
Use the UP or DOWN key to move the to selection you wish to change. Press the E key and the selected will change from Enable to Disable or vice versa.
Select Exit to return to main Manager Level Menu.
6. Dose Program Lock
09.30
Manager Level Menu
2.Group Head Positi on 3. Time/Date 4.Button Labels 5.Volume Buttons 6.Dose Program Lock
Once the volumetrics have been set, you can lockout other users from accessing the volumetric setting program. Move the cursor to be in line with the Dose Program Lock by using the UP or DOWN key. Press the E key to enter menu.
Use the left and right direction key to underline ENABLE or DISABLE the lock. Press the E key to accept selection and return to the main Manager Level Menu.
Disavè Shot Timer Manual V11 Sept 2020
pg. 13
Dose Program Lock
ENABLE DISABLE
7. Shot Timer ON/OFF
09.30
Manager Level
Menu
3. Time/Date 4.Button Labels 5.Volume Buttons 6.Dose Program Lock 7.Shot Timer On/OFF
It is possible to disable/enable the shot timer function if not required.
Move the cursor to be in line with the Shot Timer ON/OFF by using the UP or DOWN key. Press the E key to enter menu.
Display Shot Timer ON OFF
R
L
Use LEFT and RIGHT buttons to move the underline to ON or OFF. Press the E key to save and exit back to the Manager Level Menu.
8. Shot Time Alarm
09.30
Manager Level Menu
4.Button Labels 5.Volume Buttons 6.Dose Program Lock 7.Shot Timer On/OFF 8.Shot Time Alarm
It is possible to adjust the range the shot timer alarm will display RED or GREEN from the set shot time for each button.
Move the cursor to be in line with the Shot Timer Alarm by using the UP or DOWN key. Press the E key to enter menu.
Disavè Shot Timer Manual V11 Sept 2020
pg. 14
Shot Time Alarm
+/-3sec
Use B1 and B2 to increase or decrease the alarm value. The set value will add or subtract from the set shot time to give a range the drink will display as green.
i.e. Shot time set for 30secs with Alarm set +/-3sec will give a green result for drinks made between 27-33seconds. Drinks made outside of this range will be RED.
*To turn OFF the RED and GREEN signalling set the Shot Time Alarm value to 0.
9. Transfer Config
09.30
Manager Level Menu
5.Volume Buttons 6.Dose Program Lock 7.Shot Timer On/OFF 8.Shot Time Alarm 9.Transfer Config
It is possible to transfer all configurations from the board to a USB memory stick or from the stick to the board to clone a new board to save time.
Move the cursor to be in line with the Transfer Config selection by using the UP or DOWN key. Press the E key to enter menu.
Transfer Config
Board -> USB USB -> Board Exit USB device not found
If no USB device is inserted a RED notice will be displayed otherwise it will not be displayed.
Move the cursor to make selection from the board to USB or visa versa. Press the E key to transfer the configuration.
Move to EXIT and press the E key to save and exit back to the Manager Level Menu.
Disavè Shot Timer Manual V11 Sept 2020
pg. 15
EXIT Manager Level Menu
To exit the Manager Menu, select Exit Menu with the and press the E key.
09.30
Manager Level Menu
6.Dose Program Lock 7.Shot Timer On/OFF 8.Shot Time Alarm 9.Transfer Config Exit Menu
Disavè Shot Timer Manual V11 Sept 2020
pg. 16
Documents / Resources
 |
disave V11 Shot Timer [pdf] User Manual V11, 09.30, 30.0, V11 Shot Timer, V11, Shot Timer, Timer |
