Geode Jasper Rugged Computer System
GEODE JASPER
Rugged Computer System
User Manual
|
Revision |
Date |
Comments |
|
0.1 |
04/06/2024 |
Initial Version |
|
|
|
|
|
|
|
|
FOR TECHNICAL SUPPORT
PLEASE CONTACT: support@diamondsystems.com
Copyright 2024
Diamond Systems Corporation
158 Commercial Street
Sunnyvale, CA 94086 USA
Tel 1-650-810-2500
Fax 1-650-810-2525
www.diamondsystems.com
Geode Jasper User Manual Revision A www.diamondsystems.com Page 2 of 33
1. IMPORTANT SAFE HANDLING INFORMATION
WARNING!
ESD-Sensitive Electronic Equipment
Observe ESD-safe handling procedures when working with this product. Always use this product in a properly grounded work area and wear appropriate ESD-preventive clothing and/or accessories. Always store this product in ESD-protective packaging when not in use.
Safe Handling Precautions
The SabreNet 12000 contains a high-density connector with many connections to sensitive electronic components. This creates many opportunities for accidental damage during handling, installation and connection to other equipment. The list here describes common causes of failure found on boards and systems returned to Diamond Systems for repair. This information is provided as a source of advice to help you prevent damaging your Diamond (or any vendor’s) boards.
ESD damage – This type of damage is usually almost impossible to detect, because there is no visual sign of failure or damage. The symptom is that the board eventually simply stops working, because some component becomes defective. Usually the failure can be identified and the chip can be replaced. To prevent ESD damage, always follow proper ESD-prevention practices when handling computer boards.
Power supply wired backwards – Our power supplies and boards are not designed to withstand a reverse power supply connection. This will destroy each IC that is connected to the power supply (i.e. almost all ICs). In this case the board will most likely will be unrepairable and must be replaced. A chip destroyed by reverse power or by excessive power will often have a visible hole on the top or show some deformation on the top surface due to vaporization inside the package. Check twice before applying power!
Geode Jasper User Manual Revision A www.diamondsystems.com Page 3 of 33
2. DESCRIPTION
Geode Jasper is a rugged COM Express Compact/Basic type 6 carrier board system with MIL . The carrier is designed to support a variety of COM Express modules to provide both rapid product line expansion with a variety of processors and long life by enabling simple replacement of the COM when the designed-in one becomes obsolete.
The COM Express module mounts on the bottom side of the board, and the PCIe104 expansion sockets are on the top side. The board dimensions are 4.000” x 5.750”, slightly larger than both COM Express compact/basic and PCIe104 modules. The larger size is necessitated due to the incompatibility between the mounting hole patterns of the two form factors plus the desire to provide increased PCB coastline for I/O connectors. A thicker PCB (.090” / 2.3mm), latching I/O connectors, and full -40/+85C operating temperature provide increased ruggedness, enabling the board to work reliably in mobile and harsh environment applications.
2.1 System features
|
Sl No |
Component |
Feature |
Qty |
|
1 |
Power |
12V DC supply or 9 to 36V DC supply(With Power Filter Board) |
1 |
|
2 |
CPU |
COM Express Module with Inter i7, 32GB/64GB RAM support |
1 |
|
3 |
Display |
HDMI Interface |
1 |
|
4 |
Ethernet |
2x 1Gbps |
2 |
|
5 |
USB |
USB2.0 & USB3.0 |
2x USB2.0, 2x USB3.0 |
|
6 |
Digital I/O |
Extended I/O capability |
4 GPI and 4 GPIO (3.3/5V Compatible) |
|
7 |
Serial Port |
RS232/RS422/RS485 |
4xRS232/RS422/RS485 |
|
8 |
Audio |
IN, OUT, MIC |
1 ports each |
|
9 |
Utility |
I2C, SPI & Power Signals |
1 |
|
10 |
Expansion IO |
Expansion IO signals |
2 Ports |
2.2 I/O Features and Connector Types
|
Feature |
Description |
Connector Type |
|
Power |
+12V DC / +9V to +36V input supply with MIL-STD-461 filtering |
D38999/20WC4PN |
|
RTC |
3V power input for RTC functionality |
1066 |
|
USB |
2x USB 3.0/USB2.0 |
SJT00RT12-35S014 |
|
2x USB2.0 |
D38999/20KE35BN |
|
|
Ethernet Display |
ETH-1 10/100/1000Mbps from COM module |
D38999/20KE35BN |
|
ETH-2 10/100/1000Mbps via I210 Ethernet controller |
|
|
|
1x HDMI 2.0a/b directly from the COM module |
SJT00RT12-35DS014 |
Geode Jasper User Manual Revision A www.diamondsystems.com Page 4 of 33
|
DIO |
4xGPI and 4xGPO form COM Module through expansion ports |
D38999/20WF35SN |
|
Mass Storage |
2 PCIe minicard socket with USB and SATA Minicard2 supports Nano SIM interface |
2 PCIe MiniCard 52 Position (J11 & J12) |
|
1 M.2 2242 / 2280 SATA/x1 PCIe |
M.2 Socket (J15) |
|
|
1 Standard 7pin SATA connector |
SATA Connector (J9) |
|
|
Audio |
HDA to Analog Audio converter |
|
|
PCIe104 |
4 PCIe x1 ports, 1x PCIe x16 |
156 Position Vertical Header (J1) |
|
Utility |
I2C, Reset Button, Power Button signals |
D38999/20WF35SN |
|
Antenna |
Support for two SMA connectors on the enclosure |
SMA connector on enclosure |
|
Expansion IO |
79-Pin expantion Ios support (Two qty of 2×10 pin and one 2×30 pin) |
D38999/20WG35SN |
|
Serial Ports |
4 ports Software configurable RS-232/422/485 through SP336 transceivers or 2 RS232 only |
D38999/20WF35SN |
2.3 Operating System Support
Windows 10; Ubuntu; Linux
2.4 Mechanical, Electrical, Environmental
Form factor 9.84”x7.05”x3.74”
Cooling Conduction Cooling
Power input +12V DC / 9 to +36V DSC with Filter Circuit
Operating Temp -40°C to +85°C
Weight xxx lb
Geode Jasper User Manual Revision A www.diamondsystems.com Page 5 of 33
2.5 Product Images
Geode Jasper User Manual Revision A www.diamondsystems.com Page 6 of 33
3. KEY SUBSYSTEMS
3.1 COMe Carrier System
The Geode Jasper supports various COM express modules on the carrier board.
COM Express Carrier supports COM Express Compact (95x95mm) / Basic (95x125mm) type 6 modules. The availability of features is module dependent. Design emphasis is placed on minimizing the need for BIOS customization to enable the module to work with as many different modules as possible without any customization effort.
3.2 Power Supply Specifications
Geode Jasper supports two powering options.
1. Usning on board power filder circuit on Rugged IO board
2. Using JMM-7525 external power filter board
When on board power filter is used, the Geode Jasper can be powered from +12V DC typically. On otherway, Geode Osbourne can be powered from +9V to +36V when external JMM-7525 power filter is used. The maximum allowable reflected ripple, measured at the voltage input connector is 50mV p-p.
These power supplies are sized to support the highest capacity on-board memory and have enough reserve capacity to support the below add-on features.
Following figure shows varios power options.
Geode Jasper User Manual Revision A www.diamondsystems.com Page 7 of 33
3.3 Backup Battery
A 2032 coin horizontal battery holder is provided on Jasper Carrier board. The Geode Jasper can boot and function normally without a backup battery as well. RTC of Orin module backup voltage of 3V with 1.8V to 3.46V max is required.
3.4 Ethernet Ports
COM Express Carrier provides two 10/100/1000 Ethernet ports. One port comes directly from the COM module. The other port is derived from the Intel WGI210IT PCIe Ethernet controller. This controller is accessed via x1 PCIe lane from the COM. Each port has on-board magnetics. Both Ethernet ports are available at rugged circular connector J4 on the enclosure.
3.5 PCIe Link Routing
COM Express Carrier x1 PCIe port mapping is provided below. The carrier board routes the PCIe x16 lanes from the COM Express CD connector to the PCIe104 connector banks 2 and 3.
Lane 0 – Minicard Socket1
Lane 1 – Minicard Socket2
Lane 2 – PCIe104 Type1
Lane 3 – Intel I210 Ethernet Controller
Lane 4 – PCIe104 Type1
Lane 5 – PCIe104 Type1
Lane 6 – PCIe104 Type1
Lane 7 – M.2 2280/2242
PEG x16 – PCIe104 Type1
3.6 Display
The board offers one HDMI video output option. The HDMI port is directly from the COM Module and made available on the rugged I/O connector J5. All the common choke and ESD protection circuitry are buit into the system.
3.7 Audio Interface
The HD audio from the COM module is converted to analog audio using Audio Codec. Line IN, Line OUT and Mic signals are terminated on rugged circular connector J3. The system uses internally a 2×10 pin cable assembly (DSC# 6982071) to get the Audio signals from COM carrier board to the rugged IO board.
3.8 Serial Ports
The system supports 4 serial ports using a USB to Quad UART controller (FT4232HL). The ports use SP336 transceivers (1 transceiver for 2 ports) to support RS-232, RS-422, and RS-485 protocols. The protocol is selected using GPIO pins on the FPGA in full feature (JSP BB03A) and Jumper options are given for protocol selection in Full feature without DAQ (JSP BB02D). On board jumpers are provided to enable 121-ohm line termination for RS-422 and RS-485 protocols.
The four serial ports are available on rugged circular connector J3 on the enclosure.
3.9 PCIe Minicard Socket
The system offers two full size (51mm length) or two half size Minicard sockets. Minicard interface support PCIex1 and SATA using a mux. Both minicard support USB2.0 interface.
On minicard connector1, PCIe lane 0 and SATA Port 2 are muxed using a high-speed mux IC. USB2.0 Port 6 is muxed with minicard connector 1 and PCIe104 and can be selected using jumper configuration available at JP3 on Jasper carrier board.
Geode Jasper User Manual Revision A www.diamondsystems.com Page 8 of 33
On Minicard connector2, PCIe lane 1 and SATA port 3 are muxed using high-speed mux IC. USB2.0 port 5 is also made available at the connector. Nano sim connector is supported on minicard connector 2.
Board provides 2nos onboard M2 4mm spacer on each minicard sockets to mount modules and for half minicard there are M2 2mm spacer which acts as nut for the Male to Female M2 4mm spacer provided as accessory.
3.10 USB
The Geode Jasper supports 2x USB2.0 ports routed to rugged I/O connector J4. Two numbers of USB3.2 are also routed to the rugged USB connector J7.
2 x USB2.0 ports are routed to one 2×5 headers and 3x USB 3.0/USB2.0 ports are routed to three nos of 2×5 headers.
USB2.0 port 6 is muxed between minicard socket 1 and PCIe104 and can be selected using jumper configuration at JP3.
USB port mapping is shown below:
|
USB3.0 Ports |
|
|
Port Number |
Port Termination |
|
Port 0 |
USB3.0 Header 1 |
|
Port 1 |
USB3.0 Header 2 |
|
Port 2 |
USB3.0 Header 3 |
|
Port 3 |
Not Used |
|
USB2.0 Ports |
|
|
Port Number |
Port Termination |
|
Port 0 |
USB3.0 Header 1 |
|
Port 1 |
USB3.0 Header 2 |
|
Port 2 |
USB2.0 Header |
|
Port 3 |
|
|
Port 4 |
USB to Quad UART |
|
Port 5 |
Minicard Socket2 |
|
Port 6 |
Minicard Socket1 / PCIe104 |
|
Port 7 |
USB3.0 Header 3 |
Geode Jasper User Manual Revision A www.diamondsystems.com Page 9 of 33
3.11 SATA M.2 Socket
The carrier board offers up to four SATA ports, derived from the COM express module.
M.2 2242/2280 socket supports SATA Port 0 / PCIe Lane 7 using a high-speed mux. SBC provides onboard M3 4mm spacer to mount M.2 2280 SATA SSD and M3 2mm spacer acts as nut for the Male to Female 4mm spacer provided to mount M.2 2242 SATA SSD.
Second SATA port (mapped as Port 1 from COM) is connected to an industry-standard vertical 7pin SATA connector that accepts cables with latching.
Third SATA (mapped as Port 2 from COM) and fourth (mapped as Port 2 from COM) SATA ports are made available on the first and second minicard sockets respectively using high speed mux. PCIe/SATA interface is supported depending on the type of minicard module inserted.
3.12 PCIe104 Expansion
The board offers expansion over 3 bank PCIe104 connector with 22mm stacking height.
Design supports up to four, x1 lane PCIe ports on one bank PCIe104 connector and x16 PEG port on the 2nd and 3rd bank. The PCIe ports availability depends on the COM express module used.
One of the USB2.0 (Port 6) is muxed with minicard2 can be selected using jumper configuration at JP3.
3.13 Digital I/O
The board contains a GPIO header with 4 GPI and 4 GPO available from the COM module. GPI3 (by default) is muxed with TPM IRQ.
It provides 500mA fused 3.3V supply.
The GPIO signals are available on rugged circular connector J4. The system uses internally a 2×10 pin cable assembly (DSC# 6982071) to get the GPIO signals from COM carrier board to the rugged IO board.
3.14 Utility signals
Power button, Reset and I2C signals are also made available on the circular connector J4.
3.15 Trusted Platform Module (TPM)
The board contains Infineon’s SLB 9670XQ2.0 TPM module featuring a fully TCG TPM 1.2/2.0 standard compliant module with an SPI interface. TPM can be used as a root of trust for platform integrity, remote attestation and cryptographic services. This feature will be supported based on the customer requirement and not implemented by default.
Geode Jasper User Manual Revision A www.diamondsystems.com Page 10 of 33
3.16 Expansion IO
Geode Osbourne also provides another rugged circular connector J6 on the enclosure. This can be used for IO expansion in future.
3.17 Data Acquisition
The system provides an optional data acquisition subcircuit containing analog input, analog output, and digital I/O features. This circuit is controlled by an FPGA attached to the processor via the LPC bus. A pin header on the board provides access to JTAG signals for reprogramming the FPGA on the board and in the field.
Features of the DAQ subcircuit include: 16 single-ended / 8 differential analog inputs with 16-bit resolution, programmable input ranges, and 250KSPS maximum throughput; 4 analog outputs with 16-bit resolution and programmable output ranges; and 22 digital I/O lines with selectable 3.3V/5V logic levels, selectable pull-up/down resistors, programmable direction, buffered I/O, and capability for use as counter/timer and PWM circuits.
If this option is added, the signals are available on the rugged expansion IO connector J6.
Geode Jasper User Manual Revision A www.diamondsystems.com Page 11 of 33
4. KEY INTERFACES
The interfaces on Geode Osbourne are derived from the different subsystems. A summary of the interfaces provided on the system with its provider are tabulated below:
|
Sl No |
Interface |
Subsystem |
|
1 |
HDMI |
COMe Module |
|
2 |
2x 1G Ethernet |
One from COMe Module. One from WGI210IT 1G CTRLR+PHY |
|
3 |
4xRS-232/RS422/RS485 |
Derived from SP336 |
|
4 |
2xUSB3.2 |
COMe Module |
|
5 |
2xUSB2.0 |
COMe Module |
|
6 |
4xGPI + 4xGPO |
COMe Module |
|
7 |
1x SATA M.2 |
COMe Module |
|
8 |
2x MiniPCIe Socket |
COMe Module |
|
9 |
PCIe104 Expansion Ports |
COMe Module+PCIe 104 Exp Board |
|
10 |
AUDIO – IN, OUT, MIC IN |
From ALC892-CG Audio CODEC |
|
11 |
1x I2C |
COMe Module |
|
Power |
||
|
12 |
Power |
Through external power filter (JMM 7515) or through onboard power filter on rugged IO board |
Geode Jasper User Manual Revision A www.diamondsystems.com Page 12 of 33
5. SYSTEM ARCHITECTURE
Figure 1 provides an overview of the block diagrarm of the Geode Jasper system.
Figure 1: System Architecture of Geode Osbourne
Geode Jasper User Manual Revision A www.diamondsystems.com Page 13 of 33
6. GEODE OSBOURNE MECHANICAL DRAWING AND FEATURE LOCATIONS The form factor of the system is 9.5”x8.5”x3.85”.
Figure 2: Mechanical outline, front view
Figure 3: Mechanical outline, top view
Geode Jasper User Manual Revision A www.diamondsystems.com Page 14 of 33
Figure 4: Mechanical 3D, side view
Geode Jasper User Manual Revision A www.diamondsystems.com Page 15 of 33
7. I/O CONNECTORS
Following image shows the connector details on Geode Jasper system.
Geode Jasper User Manual Revision A www.diamondsystems.com Page 16 of 33
7.1 J2 – Power Input (Power)
Geode Jasper provides D38999 series circular connector for power input. Connector pinout is as shown below:
|
D38999 Pin no. |
Signal |
|
B |
Vin |
|
C |
Vin |
|
A |
Ground |
|
D |
Ground |
|
Geode system connector |
Connector type |
MIL D38999/20WC4PN |
|
Description |
Shell type Straight Plug Material and Olive Drab Cadmium finish Plated Nickel Base Shell Size C Insert Arrangement C4 Contact type Pin Keying position Normal Keying Pins 4 |
|
|
Illustration Viewed from exterior |
|
|
|
Mating connector |
Connector Part# |
MIL D38999/26WC4SN |
|
Description |
Shell type Straight Plug Material and Olive Drab Cadmium finish Plated Nickel Base Shell Size C Insert Arrangement C4 Contact type Socket Keying position Normal Keying Pins 4 |
|
|
Illustration Viewed from exterior |
|
Geode Jasper User Manual Revision A www.diamondsystems.com Page 17 of 33
7.2 J3 – IO Connector
Geode Jasper provides four serial ports, Audio In, Audio Out, MIC ports and Expansion IO signals on to D38999 series circular connector. Connector pinout is as shown below:
|
Interface |
D38999 Pin no. |
Signal Name |
|
Serial Port 1 |
50 |
TX/TX_P/RX_P |
|
49 |
RX/RX_P |
|
|
55 |
RTS/TX_N/RX_N |
|
|
53 |
CTS/RX_N |
|
|
48 |
GND |
|
|
Serial Port 2 |
41 |
TX/TX_P/RX_P |
|
33 |
RX/RX_P |
|
|
47 |
RTS/TX_N/RX_N |
|
|
40 |
CTS/RX_N |
|
|
32 |
GND |
|
|
Serial Port 3 |
36 |
TX/TX_P/RX_P |
|
30 |
RX/RX_P |
|
|
29 |
RTS/TX_N/RX_N |
|
|
37 |
CTS/RX_N |
|
|
38 |
GND |
|
|
Serial Port 4 |
46 |
TX/TX_P/RX_P |
|
52 |
RX/RX_P |
|
|
45 |
RTS/TX_N/RX_N |
|
|
51 |
CTS/RX_N |
|
|
39 |
GND |
|
|
Expansion IOs |
31 |
D_EXP_1 |
|
23 |
D_EXP_3 |
|
|
15 |
D_EXP_5 |
|
|
14 |
D_EXP_7 |
|
|
7 |
D_EXP_9 |
|
|
6 |
D_EXP_11 |
|
|
5 |
D_EXP_13 |
|
|
11 |
D_EXP_15 |
|
|
18 |
D_EXP_17 |
|
|
25 |
D_EXP_19 |
|
|
24 |
D_EXP_2 |
|
|
16 |
D_EXP_4 |
|
|
9 |
D_EXP_6 |
|
|
8 |
D_EXP_8 |
|
|
3 |
D_EXP_10 |
|
|
2 |
D_EXP_12 |
|
|
1 |
D_EXP_14 |
|
|
4 |
D_EXP_16 |
|
|
10 |
D_EXP_18 |
|
|
17 |
D_EXP_20 |
Geode Jasper User Manual Revision A www.diamondsystems.com Page 18 of 33
|
Audio In |
42 |
LINE_OUT_L |
|
43 |
LINE_OUT_R |
|
|
34 |
AUD_GND |
|
|
Audio Out |
26 |
LINE_IN_L |
|
27 |
LINE_IN_R |
|
|
35 |
AUD_GND |
|
|
MIC In |
20 |
MIC_IN |
|
13 |
AUD_GND |
|
|
Audio GND |
21 |
AUD_GND |
|
22 |
AUD_GND |
|
|
No Connect |
12 |
NC |
|
19 |
NC |
|
|
28 |
NC |
|
|
44 |
NC |
|
|
54 |
NC |
|
Geode system connector |
Connector type |
MIL D38999/20KE35BN |
|
Description |
Shell type Straight Receptacle Material and Olive Drab Cadmium finish Plated Nickel Base Shell Size E Insert Arrangement F35 Contact type Socket Keying position Normal Keying |
|
|
Illustration Viewed from exterior |
|
|
|
Mating connector |
Connector type |
MIL D38999/26WE35PN |
|
Description |
Shell type Straight Plug Material and Olive Drab Cadmium finish Plated Nickel Base Shell Size E Insert Arrangement F35 |
Geode Jasper User Manual Revision A www.diamondsystems.com Page 19 of 33
|
|
|
Contact type Pin Keying position Normal Keying |
|
Illustration Viewed from rear (terminal insertion side) |
|
Geode Jasper User Manual Revision A www.diamondsystems.com Page 20 of 33
7.3 J4 – IO Connector
Geode Jasper provides two 1G Ethernet, two USB2.0, GPIO, I2C and power signals on to D38999 series circular connector. Connector pinout is as shown below:
|
Interface |
D38999 Pin no. |
Signal Name |
|
GBE Port 1 |
9 |
GBE0_TR0_P |
|
8 |
GBE0_TR0_N |
|
|
24 |
GBE0_TR1_P |
|
|
16 |
GBE0_TR1_N |
|
|
31 |
GBE0_TR2_P |
|
|
39 |
GBE0_TR2_N |
|
|
46 |
GBE0_TR3_P |
|
|
52 |
GBE0_TR3_N |
|
|
GBE Port2 |
51 |
GBE1_TR0_P |
|
55 |
GBE1_TR0_N |
|
|
54 |
GBE1_TR1_P |
|
|
53 |
GBE1_TR1_N |
|
|
48 |
GBE1_TR2_P |
|
|
47 |
GBE1_TR2_N |
|
|
40 |
GBE1_TR3_P |
|
|
32 |
GBE1_TR3_N |
|
|
USB2.0 Port 1 |
11 |
V_USB0_VBUS |
|
10 |
USB2_D2_CH_N |
|
|
17 |
USB2_D2_CH_P |
|
|
18 |
GND_DIG |
|
|
USB2.0 Port 2 |
2 |
V_USB1_VBUS |
|
1 |
USB2_D3_CH_N |
|
|
4 |
USB2_D3_CH_P |
|
|
5 |
GND_DIG |
|
|
|
22 |
PWRBTN# |
|
|
19 |
M_2_MEM_ERS_GPIO |
|
|
23 |
RSTBTN#_3P3 |
|
|
13 |
GND_DIG |
|
|
12 |
V_3P0_RTC |
|
|
14 |
V_3P3_S_UTILITY |
|
|
20 |
I2C_CLK |
Geode Jasper User Manual Revision A www.diamondsystems.com Page 21 of 33
|
|
21 |
I2C_DATA |
|
|
25 |
GND_DIG |
|
|
41 |
E_EXP_1 |
|
|
42 |
E_EXP_2 |
|
|
43 |
E_EXP_3 |
|
|
44 |
E_EXP_4 |
|
|
45 |
E_EXP_5 |
|
|
34 |
E_EXP_6 |
|
|
35 |
E_EXP_7 |
|
|
36 |
E_EXP_8 |
|
|
37 |
E_EXP_9 |
|
|
38 |
E_EXP_10 |
|
|
26 |
GND_DIG |
|
No Connect |
6 |
NC |
|
7 |
NC |
|
|
15 |
NC |
|
|
27 |
NC |
|
|
28 |
NC |
|
|
29 |
NC |
|
|
30 |
NC |
|
|
33 |
NC |
|
|
50 |
NC |
|
Geode system connector |
Connector type |
MIL D38999/20KE35BN |
|
Description |
Shell type Straight Receptacle Material and Olive Drab Cadmium finish Plated Nickel Base Shell Size E Insert Arrangement F35 Contact type Socket Keying position Normal Keying |
Geode Jasper User Manual Revision A www.diamondsystems.com Page 22 of 33
|
|
Illustration Viewed from exterior |
|
|
Mating connector |
Connector type |
MIL D38999/26WE35PN |
|
Description |
Shell type Straight Plug Material and Olive Drab Cadmium finish Plated Nickel Base Shell Size E Insert Arrangement F35 Contact type Pin Keying position Normal Keying |
|
|
Illustration Viewed from rear (terminal insertion side) |
|
Geode Jasper User Manual Revision A www.diamondsystems.com Page 23 of 33
7.4 J7 – HDMI Connector
Geode Jasper provides HDMI interface signals which are terminated with SJT00RT12 series circular connector. Connector pinout is as shown below:
|
D38999 Pin no. |
Signal |
|
1 |
HDMI_DP2_TX0_CON_P |
|
2 |
HDMI_DP2_TX0_CON_N |
|
15 |
GND_DIG |
|
3 |
HDMI_DP2_TX1_CON_P |
|
4 |
HDMI_DP2_TX1_CON_N |
|
16 |
GND_DIG |
|
5 |
HDMI_DP2_TX2_CON_P |
|
6 |
HDMI_DP2_TX2_CON_N |
|
17 |
GND_DIG |
|
9 |
HDMI_DP2_TX3_CON_P |
|
10 |
HDMI_DP2_TX3_CON_N |
|
19 |
GND_DIG |
|
20 |
HDMI_CEC_CON |
|
|
NC |
|
12 |
HDMI_SCL_CON |
|
13 |
HDMI_SDA_CON |
|
14 |
GND_DIG |
|
21 |
V_5P0_HDMI |
|
7 |
HDMI_HPD_CON |
|
22 |
GND_DIG |
|
8 |
NC |
|
11 |
NC |
|
18 |
NC |
|
Geode System connector |
Connector type |
MIL SJT00RT12-35S014 |
|
Description |
Shell type Straight Receptacle Material and Olive Drab Cadmium finish Plated Nickel Base Shell Size 12 Insert Arrangement 12-35 Contact type Female Socket Keying position Normal Keying Pins 22 |
|
|
Illustration Viewed from exterior |
|
Geode Jasper User Manual Revision A www.diamondsystems.com Page 24 of 33
|
Mating connector |
Connector type |
MIL SJTG06RT12-35DP014 |
|
Description |
Shell type Straight Plug Material and Olive Drab Cadmium finish Plated Nickel Base Shell Size 12 Insert Arrangement 12-35 Contact type Pin Keying position Normal Keying Pins 22 |
|
|
Illustration Viewed from rear (terminal insertion side) |
|
7.5 J5 – USB3.2 Connector
Geode Jasper provides 2xUSB3.2 interface signals which are terminated with SJT00RT12 series circular connector. Connector pinout is as shown below:
|
USB Port# |
D38999 Pin no. |
Signal |
|
USB3.0 Port 1 |
1 |
USB3_VBUS |
|
7 |
USB D |
|
|
8 |
USB D+ |
|
|
2 |
GND |
|
|
5 |
USB3_SSRX |
|
|
6 |
USB3_SSRX+ |
|
|
16 |
GND |
|
|
3 |
USB3_SSTX |
|
|
4 |
USB3_SSTX+ |
|
|
USB3.0 Port 2 |
14 |
USB3_VBUS |
|
22 |
USB D |
|
|
18 |
USB D+ |
|
|
13 |
GND |
|
|
11 |
USB3_SSRX |
|
|
12 |
USB3_SSRX+ |
|
|
19 |
GND |
|
|
9 |
USB3_SSTX |
|
|
10 |
USB3_SSTX+ |
|
Geode system connector |
Connector type |
MIL SJT00RT12-35S014 |
|
Description |
Shell type Straight Receptacle Material and Olive Drab Cadmium finish Plated Nickel Base |
Geode Jasper User Manual Revision A www.diamondsystems.com Page 25 of 33
|
|
|
Shell Size 12 Insert Arrangement 12-35 Contact type Female Socket Keying position Normal Keying Pins 22 |
|
Illustration Viewed from exterior |
|
|
|
Mating connector |
Connector type |
MIL SJTG06RT12-35DP014 |
|
Description |
Shell type Straight Plug Material and Olive Drab Cadmium finish Plated Nickel Base Shell Size 12 Insert Arrangement 12-35 Contact type Pin Keying position Normal Keying Pins 22 |
|
|
Illustration Viewed from rear (terminal insertion side) |
|
7.6 J2 – I/O Connector
The 1G Eth, 2x CAN, DIO, Audio, 4x Serial ports, 2x USB2.0 and Control Signals of the Geode System are terminated with a D38999 series circular connector. The connector pinouts are as shown below:
|
Port Type |
D38999 Pin no. |
Signal |
|
1G Ethernet Port |
10 |
GBE0_TR0_P |
|
4 |
GBE0_TR0_N |
|
|
17 |
GBE0_TR1_P |
|
|
25 |
GBE0_TR1_N |
Geode Jasper User Manual Revision A www.diamondsystems.com Page 26 of 33
|
|
1 |
GBE0_TR2_P |
|
5 |
GBE0_TR2_N |
|
|
2 |
GBE0_TR3_P |
|
|
3 |
GBE0_TR3_N |
|
|
USB2 Port 1 |
64 |
USB VBUS |
|
66 |
USB D |
|
|
65 |
USB D+ |
|
|
62 |
GND |
|
|
USB2 Port 2 |
44 |
USB VBUS |
|
51 |
USB D |
|
|
43 |
USB D+ |
|
|
58 |
GND |
|
|
Serial Port 1 (RS232/RS422/RS485) |
11 |
TX/TX_P/RX_P |
|
13 |
RX/RX_P |
|
|
12 |
RTS/TX_N/RX_N |
|
|
14 |
CTS/RX_N |
|
|
15 |
GND_DIG |
|
|
Serial Port 2 (RS232/RS422/RS485) |
16 |
TX/TX_P/RX_P |
|
19 |
RX/RX_P |
|
|
9 |
RTS/TX_N/RX_N |
|
|
20 |
CTS/RX_N |
|
|
21 |
GND_DIG |
|
|
Serial Port 3 (RS232) |
35 |
TX |
|
36 |
RX |
|
|
38 |
RTS |
|
|
37 |
CTS |
|
|
39 |
GND |
|
|
Serial Port 4 (RS232) |
41 |
TX |
|
40 |
RX |
|
|
42 |
GND |
|
|
Power Signals |
45 |
SYS_RST_IN_N |
|
47 |
BUTTON_POWER_ON_N |
|
|
50 |
FORCE_RECOVERY |
|
|
48 |
MEM_ERS |
|
|
I2C Signals |
52 |
I2C_CLK_3P3 |
|
53 |
I2C_ DAT_3P3 |
|
|
CAN Signals |
6 |
CAN0_H |
|
23 |
CAN1_L |
|
|
7 |
CAN0_L |
|
|
22 |
CAN1_H |
|
|
DIO Signals |
34 |
DIO_PA0 |
|
26 |
DIO_PA1 |
|
|
27 |
DIO_PA2 |
|
|
28 |
DIO_PA3 |
|
|
29 |
DIO_PA4 |
Geode Jasper User Manual Revision A www.diamondsystems.com Page 27 of 33
|
|
30 |
DIO_PA5 |
|
31 |
DIO_PA6 |
|
|
32 |
DIO_PA7 |
|
|
Audio Signals |
57 |
AUDIO_OUT_L |
|
63 |
AUDIO_OUT_R |
|
|
56 |
GND_AUD |
|
|
61 |
AUDIO_MIC_IN |
|
|
60 |
GND_AUD |
|
|
+5V |
54 |
V_5P0 |
|
Ground |
8 |
GND |
|
46 |
GND |
|
|
49 |
GND |
|
|
55 |
GND |
|
|
24 |
GND |
|
|
33 |
GND |
|
|
59 |
GND |
|
|
No Connect |
18 |
NC |
|
Geode system connector |
Connector type |
MIL D38999/20WF35SN |
|
Description |
Shell type Straight Receptacle Material and Olive Drab Cadmium finish Plated Nickel Base Shell Size F Insert Arrangement F35 Contact type Socket Keying position Normal Keying |
|
|
Illustration Viewed from exterior |
|
|
|
Mating connector |
Connector type |
MIL D38999/26WF35PN |
|
Description |
Shell type Straight Plug |
Geode Jasper User Manual Revision A www.diamondsystems.com Page 28 of 33
|
|
|
Material and Olive Drab Cadmium finish Plated Nickel Base Shell Size F Insert Arrangement F35 Contact type Pin Keying position Normal Keying |
|
Illustration Viewed from rear (terminal insertion side) |
|
Geode Jasper User Manual Revision A www.diamondsystems.com Page 29 of 33
8. GEODE JASPER JUMPER CONFIGURATIONS
8.1 Jumpers on Jasper COM Carrier Board
The Jumper blocks on the Jasper COM carrier board can be configured to enable/disable or alter the default signal routing settings on the circuit, using Jumper shunts.
Figure 4: Jumper Blocks on Jasper Carrier Board
The following table describes the Jumper Blocks on the carrier board.
|
Name |
Function |
|
JP1 |
FPGA address selection |
|
JP2 |
LVDS_BKLT and LVDS_VDD voltage level selection |
|
JP3 |
USB TO MPCIE/PCIE/104, input voltage selection |
|
JP4 |
Serial port mode selection |
|
JP5 |
DIO Voltage and PU/PD selection |
|
JP6 |
Serial Port 3 & 4 termination selection |
|
JP7 |
Serial Port 1 & 2 termination selection |
Geode Jasper User Manual Revision A www.diamondsystems.com Page 30 of 33
8.2 Jumper Block JP1
JP1 Jumpers Configuration are provided to set the address of the FPGA.
|
Position |
Function |
IN |
OUT |
|
A0 |
FPGA Address 0 |
Refer following table |
|
|
A1 |
FPGA Address 1 |
Refer following table |
|
|
A2 |
FPGA Address 2 |
Refer following table |
|
|
A3 |
FPGA Address 3 |
Refer following table |
|
*Default Address = 0x240
FPGA Addresses
FPGA Address A0 A1 A2 A3 FPGA Address – 0X100 IN IN IN IN FPGA Address – 0X120 IN IN IN OUT FPGA Address – 0X140 IN IN OUT IN FPGA Address – 0X180 IN IN OUT OUT FPGA Address – 0X200 IN OUT IN IN FPGA Address – 0X240 IN* OUT* IN* OUT* FPGA Address – 0X280 IN OUT OUT IN FPGA Address – 0X2C0 IN OUT OUT OUT FPGA Address – 0X300 OUT IN IN IN FPGA Address – 0X340 OUT IN IN OUT FPGA Address – 0X380 OUT IN OUT IN FPGA Address – 0X3C0 OUT IN OUT OUT FPGA Address – 0X400 OUT OUT IN IN FPGA Address – Reserved OUT OUT IN OUT FPGA Address – Reserved OUT OUT OUT IN
FPGA Address – Reserved OUT OUT OUT OUT *Default Mode
Note:
1. Base address must be selected based on COM module used with Jasper.
2. Whiskey Lake COM supports 0x240 and 0x280 base address.
3. Tiger Lake COM supports 0x240 base address.
Geode Jasper User Manual Revision A www.diamondsystems.com Page 31 of 33
8.3 Jumper Block JP2
JP2 Jumpers are provided to select the voltage level of the LVDS display and backlight. The configuration is as shown below:
|
Position |
Function |
IN |
OUT |
|
12V |
LCD Backlight Voltage |
12V* |
– |
|
5V |
LCD Backlight Voltage |
5V |
– |
|
5V |
LCD VDD Voltage |
5V |
– |
|
3V3 |
LCD VDD Voltage |
3.3V* |
– |
*Default Mode
Note: Make sure 5V and 3V3 Jumper are not IN at same time.
8.4 Jumper Block JP3
JP3 Jumpers Configuration are provided select the configuration pins of the FPGA, USB interface and Power IN option. USB interface from COMe Type AB connector is multiplex to mPCIe and PCIe/104 connector. Board can be powered with 18V-36V wide input or 12V fixed supply.
|
Position |
Function |
IN |
OUT |
|
U0 |
FPGA Config 0 |
TBD |
TBD* |
|
U1 |
FPGA Config 1 |
TBD |
TBD* |
|
USB |
USB SEL |
Minicard |
PCIe104* |
|
12VIN |
Wide Input SEL |
12V Fixed |
Wide Input* |
*Default Mode
8.5 Jumper Block JP4
JP2 Jumpers are provided to select the mode of serial ports 1, 2, 3 & 4. SC0 and SC1 jumpers are used to select mode for serial ports 1 & 2 and SC2 and SC3 jumpers are used to select mode for serial ports 3 & 4. The configuration is as shown below:
|
Position |
Port |
RS232 |
RS485 |
RS422 |
Internal Loop |
|
SC0 |
1&2 |
IN* |
OUT |
OUT |
IN |
|
SC1 |
1&2 |
OUT* |
IN |
OUT |
IN |
|
SC2 |
3&4 |
IN* |
OUT |
OUT |
IN |
|
SC3 |
3&4 |
OUT* |
IN |
OUT |
IN |
*Default Mode
Note: Make sure 5V and 3V3 Jumper are not IN at same time.
Geode Jasper User Manual Revision A www.diamondsystems.com Page 32 of 33
8.6 Jumper Block JP5
JP2 Jumpers are provided to select the voltage level and Pullup/pull down configuration of the DIO. By default, the DIOs are 3.3 Volare pulled down. The configuration is as shown below:
|
Position |
Function |
IN |
OUT |
|
5V |
DIO Voltage Level |
5V |
|
|
3V3 |
DIO Voltage Level |
3.3V* |
|
|
PU |
DIO Pull up Enable |
Enabled Disabled |
|
|
PD |
DIO Pull down Enable |
Enabled* Disabled |
|
*Default Mode
Note: Make sure 5V and 3V3 Jumper are not IN at same time.
8.7 Jumper Block JP6
JP2 Jumpers are provided to enable and disable the termination of serial ports3-4. The configuration is as shown below:
|
Position |
Function |
IN |
OUT |
|
TX3 |
Serial Port3 TX Termination |
Enabled |
Disabled* |
|
RX3 |
Serial Port3 RX Termination |
Enabled |
Disabled* |
|
TX4 |
Serial Port4 TX Termination |
Enabled |
Disabled* |
|
RX4 |
Serial Port4 RX Termination |
Enabled |
Disabled* |
*Default Mode
8.8 Jumper Block JP7
JP2 Jumpers are provided to enable and disable the termination of serial ports1-2. The configuration is as shown below:
|
Position |
Function |
IN |
OUT |
|
TX1 |
Serial Port1 TX Termination |
Enabled |
Disabled* |
|
RX1 |
Serial Port1 RX Termination |
Enabled |
Disabled* |
|
TX2 |
Serial Port2 TX Termination |
Enabled |
Disabled* |
|
RX2 |
Serial Port3 RX Termination |
Enabled |
Disabled* |
*Default Mode
Geode Jasper User Manual Revision A www.diamondsystems.com Page 33 of 33
Documents / Resources
 |
DIAMOND SYSTEMS Geode Jasper Rugged Computer System [pdf] User Manual Geode Jasper Rugged Computer System, Rugged Computer System, Computer System |
