User Manual for DIAMOND SYSTEMS models including: Geode Jasper Rugged Computer System, Rugged Computer System, Computer System
File Info : application/pdf, 33 Pages, 2.44MB
DocumentDocumentGEODE JASPER Rugged Computer System User Manual Revision 0.1 Date Comments 04/06/2024 Initial Version FOR TECHNICAL SUPPORT PLEASE CONTACT: support@diamondsystems.com Copyright 2024 Diamond Systems Corporation 158 Commercial Street Sunnyvale, CA 94086 USA Tel 1-650-810-2500 Fax 1-650-810-2525 www.diamondsystems.com TABLE OF CONTENTS 1. IMPORTANT SAFE HANDLING INFORMATION....................................................................3 2. DESCRIPTION..........................................................................................................................4 2.1 SYSTEM FEATURES............................................................................................................................... 4 2.2 I/O FEATURES AND CONNECTOR TYPES............................................................................................... 4 2.3 OPERATING SYSTEM SUPPORT ............................................................................................................. 5 2.4 MECHANICAL, ELECTRICAL, ENVIRONMENTAL ................................................................................... 5 2.5 PRODUCT IMAGES ................................................................................................................................ 6 3. KEY SUBSYSTEMS .................................................................................................................7 3.1 COME CARRIER SYSTEM..................................................................................................................... 7 3.2 POWER SUPPLY SPECIFICATIONS ......................................................................................................... 7 3.3 BACKUP BATTERY ............................................................................................................................... 8 3.4 ETHERNET PORTS................................................................................................................................. 8 3.5 PCIE LINK ROUTING ............................................................................................................................ 8 3.6 DISPLAY............................................................................................................................................... 8 3.7 AUDIO INTERFACE ............................................................................................................................... 8 3.8 SERIAL PORTS ...................................................................................................................................... 8 3.9 PCIE MINICARD SOCKET ..................................................................................................................... 8 3.10 USB..................................................................................................................................................... 9 3.11 SATA M.2 SOCKET ........................................................................................................................... 10 3.12 PCIE104 EXPANSION ......................................................................................................................... 10 3.13 DIGITAL I/O ....................................................................................................................................... 10 3.14 UTILITY SIGNALS ............................................................................................................................... 10 3.15 TRUSTED PLATFORM MODULE (TPM) ............................................................................................... 10 3.16 EXPANSION IO ................................................................................................................................... 11 3.17 DATA ACQUISITION ........................................................................................................................... 11 4. KEY INTERFACES .................................................................................................................12 5. SYSTEM ARCHITECTURE ....................................................................................................13 6. GEODE OSBOURNE MECHANICAL DRAWING AND FEATURE LOCATIONS ................14 7.1 J2 - POWER INPUT (POWER) ............................................................................................................... 17 7.2 J3 IO CONNECTOR........................................................................................................................... 18 7.3 J4 IO CONNECTOR........................................................................................................................... 21 7.4 J7 HDMI CONNECTOR .................................................................................................................... 24 7.5 J5 USB3.2 CONNECTOR .................................................................................................................. 25 7.6 J2 - I/O CONNECTOR .......................................................................................................................... 26 8. GEODE JASPER JUMPER CONFIGURATIONS..................................................................30 8.1 JUMPERS ON JASPER COM CARRIER BOARD ..................................................................................... 30 8.2 JUMPER BLOCK JP1 ........................................................................................................................... 31 8.3 JUMPER BLOCK JP2 ........................................................................................................................... 32 8.4 JUMPER BLOCK JP3 ........................................................................................................................... 32 8.5 JUMPER BLOCK JP4 ........................................................................................................................... 32 8.6 JUMPER BLOCK JP5 ........................................................................................................................... 33 8.7 JUMPER BLOCK JP6 ........................................................................................................................... 33 8.8 JUMPER BLOCK JP7 ........................................................................................................................... 33 Geode Jasper User Manual Revision A www.diamondsystems.com Page 2 of 33 1. IMPORTANT SAFE HANDLING INFORMATION WARNING! ESD-Sensitive Electronic Equipment Observe ESD-safe handling procedures when working with this product. Always use this product in a properly grounded work area and wear appropriate ESD-preventive clothing and/or accessories. Always store this product in ESD-protective packaging when not in use. Safe Handling Precautions The SabreNet 12000 contains a high density connector with many connections to sensitive electronic components. This creates many opportunities for accidental damage during handling, installation and connection to other equipment. The list here describes common causes of failure found on boards and systems returned to Diamond Systems for repair. This information is provided as a source of advice to help you prevent damaging your Diamond (or any vendor's) boards. ESD damage This type of damage is usually almost impossible to detect, because there is no visual sign of failure or damage. The symptom is that the board eventually simply stops working, because some component becomes defective. Usually the failure can be identified and the chip can be replaced. To prevent ESD damage, always follow proper ESD-prevention practices when handling computer boards. Power supply wired backwards Our power supplies and boards are not designed to withstand a reverse power supply connection. This will destroy each IC that is connected to the power supply (i.e. almost all ICs). In this case the board will most likely will be unrepairable and must be replaced. A chip destroyed by reverse power or by excessive power will often have a visible hole on the top or show some deformation on the top surface due to vaporization inside the package. Check twice before applying power! Geode Jasper User Manual Revision A www.diamondsystems.com Page 3 of 33 2. DESCRIPTION Geode Jasper is a rugged COM Express Compact/Basic type 6 carrier board system with MIL . The carrier is designed to support a variety of COM Express modules to provide both rapid product line expansion with a variety of processors and long life by enabling simple replacement of the COM when the designed-in one becomes obsolete. The COM Express module mounts on the bottom side of the board, and the PCIe104 expansion sockets are on the top side. The board dimensions are 4.000" x 5.750", slightly larger than both COM Express compact/basic and PCIe104 modules. The larger size is necessitated due to the incompatibility between the mounting hole patterns of the two form factors plus the desire to provide increased PCB coastline for I/O connectors. A thicker PCB (.090" / 2.3mm), latching I/O connectors, and full -40/+85C operating temperature provide increased ruggedness, enabling the board to work reliably in mobile and harsh environment applications. 2.1 System features Sl No Component 1 Power 2 CPU 3 Display 4 Ethernet 5 USB 6 Digital I/O 7 Serial Port 8 Audio 9 Utility 10 Expansion IO Feature Qty 12V DC supply or 9 to 36V DC 1 supply(With Power Filter Board) COM Express Module with Inter i7, 1 32GB/64GB RAM support HDMI Interface 1 2x 1Gbps 2 USB2.0 & USB3.0 2x USB2.0, 2x USB3.0 Extended I/O capability 4 GPI and 4 GPIO (3.3/5V Compatible) RS232/RS422/RS485 4xRS232/RS422/RS485 IN, OUT, MIC 1 ports each I2C, SPI & Power Signals 1 Expansion IO signals 2 Ports 2.2 I/O Features and Connector Types Feature Power RTC USB Ethernet Display Description +12V DC / +9V to +36V input supply with MIL-STD-461 filtering 3V power input for RTC functionality 2x USB 3.0/USB2.0 2x USB2.0 ETH-1 10/100/1000Mbps from COM module ETH-2 10/100/1000Mbps via I210 Ethernet controller 1x HDMI 2.0a/b directly from the COM module Connector Type D38999/20WC4PN 1066 SJT00RT12-35S014 D38999/20KE35BN D38999/20KE35BN SJT00RT12-35DS014 Geode Jasper User Manual Revision A www.diamondsystems.com Page 4 of 33 DIO Mass Storage 4xGPI and 4xGPO form COM Module through expansion ports 2 PCIe minicard socket with USB and SATA Minicard2 supports Nano SIM interface 1 M.2 2242 / 2280 SATA/x1 PCIe 1 Standard 7pin SATA connector Audio HDA to Analog Audio converter PCIe104 4 PCIe x1 ports, 1x PCIe x16 Utility I2C, Reset Button, Power Button signals Antenna Support for two SMA connectors on the enclosure Expansion IO Serial Ports 79-Pin expantion Ios support (Two qty of 2x10 pin and one 2x30 pin) 4 ports Software configurable RS-232/422/485 through SP336 transceivers or 2 RS232 only 2.3 Operating System Support Windows 10; Ubuntu; Linux 2.4 Mechanical, Electrical, Environmental Form factor 9.84"x7.05"x3.74" Cooling Conduction Cooling Power input +12V DC / 9 to +36V DSC with Filter Circuit Operating Temp -40°C to +85°C Weight xxx lb D38999/20WF35SN 2 PCIe MiniCard 52 Position (J11 & J12) M.2 Socket (J15) SATA Connector (J9) 156 Position Vertical Header (J1) D38999/20WF35SN SMA connector on enclosure D38999/20WG35SN D38999/20WF35SN Geode Jasper User Manual Revision A www.diamondsystems.com Page 5 of 33 2.5 Product Images Geode Jasper User Manual Revision A www.diamondsystems.com Page 6 of 33 3. KEY SUBSYSTEMS 3.1 COMe Carrier System The Geode Jasper supports various COM express modules on the carrier board. COM Express Carrier supports COM Express Compact (95x95mm) / Basic (95x125mm) type 6 modules. The availability of features is module dependent. Design emphasis is placed on minimizing the need for BIOS customization to enable the module to work with as many different modules as possible without any customization effort. 3.2 Power Supply Specifications Geode Jasper supports two powering options. 1. Usning on board power filder circuit on Rugged IO board 2. Using JMM-7525 external power filter board When on board power filter is used, the Geode Jasper can be powered from +12V DC typically. On otherway, Geode Osbourne can be powered from +9V to +36V when external JMM-7525 power filter is used. The maximum allowable reflected ripple, measured at the voltage input connector is 50mV p-p. These power supplies are sized to support the highest capacity on-board memory and have enough reserve capacity to support the below add-on features. Following figure shows varios power options. Geode Jasper User Manual Revision A www.diamondsystems.com Page 7 of 33 3.3 Backup Battery A 2032 coin horizontal battery holder is provided on Jasper Carrier board. The Geode Jasper can boot and function normally without a backup battery as well. RTC of Orin module backup voltage of 3V with 1.8V to 3.46V max is required. 3.4 Ethernet Ports COM Express Carrier provides two 10/100/1000 Ethernet ports. One port comes directly from the COM module. The other port is derived from the Intel WGI210IT PCIe Ethernet controller. This controller is accessed via x1 PCIe lane from the COM. Each port has on-board magnetics. Both Ethernet ports are available at rugged circular connector J4 on the enclosure. 3.5 PCIe Link Routing COM Express Carrier x1 PCIe port mapping is provided below. The carrier board routes the PCIe x16 lanes from the COM Express CD connector to the PCIe104 connector banks 2 and 3. Lane 0 Minicard Socket1 Lane 1 Minicard Socket2 Lane 2 PCIe104 Type1 Lane 3 Intel I210 Ethernet Controller Lane 4 PCIe104 Type1 Lane 5 PCIe104 Type1 Lane 6 PCIe104 Type1 Lane 7 M.2 2280/2242 PEG x16 PCIe104 Type1 3.6 Display The board offers one HDMI video output option. The HDMI port is directly from the COM Module and made available on the rugged I/O connector J5. All the common choke and ESD protection circuitry are buit in to the system. 3.7 Audio Interface The HD audio from the COM module is converted to analog audio using Audio Codec. Line IN, Line OUT and Mic signals are terminated on rugged circular connector J3. The system uses internally a 2x10 pin cable assembly (DSC# 6982071) to get the Audio signals from COM carrier board to the rugged IO board. 3.8 Serial Ports The system supports 4 serial ports using a USB to Quad UART controller (FT4232HL). The ports use SP336 transceivers (1 transceiver for 2 ports) to support RS-232, RS-422, and RS-485 protocols. The protocol is selected using GPIO pins on the FPGA in full feature (JSP BB03A) and Jumper options are given for protocol selection in Full feature without DAQ (JSP BB02D). On board jumpers are provided to enable 121-ohm line termination for RS-422 and RS-485 protocols. The four serial ports are available on rugged circular connector J3 on the enclosure. 3.9 PCIe Minicard Socket The system offers two full size (51mm length) or two half size Minicard sockets. Minicard interface support PCIex1 and SATA using a mux. Both minicard support USB2.0 interface. On minicard connector1, PCIe lane 0 and SATA Port 2 are muxed using a high-speed mux IC. USB2.0 Port 6 is muxed with minicard connector 1 and PCIe104 and can be selected using jumper configuration available at JP3 on Jasper carrier board. Geode Jasper User Manual Revision A www.diamondsystems.com Page 8 of 33 On Minicard connector2, PCIe lane 1 and SATA port 3 are muxed using high-speed mux IC. USB2.0 port 5 is also made available at the connector. Nano sim connector is supported on minicard connector 2. Board provides 2nos onboard M2 4mm spacer on each minicard sockets to mount modules and for half minicard there are M2 2mm spacer which acts as nut for the Male to Female M2 4mm spacer provided as accessory. 3.10 USB The Geode Jasper supports 2x USB2.0 ports routed to rugged I/O connector J4. Two numbers of USB3.2 are also routed to the rugged USB connector J7. 2 x USB2.0 ports are routed to one 2x5 headers and 3x USB 3.0/USB2.0 ports are routed to three nos of 2x5 headers. USB2.0 port 6 is muxed between minicard socket 1 and PCIe104 and can be selected using jumper configuration at JP3. USB port mapping is shown below: USB3.0 Ports Port Number Port 0 Port 1 Port 2 Port 3 USB2.0 Ports Port Number Port 0 Port 1 Port 2 Port 3 Port 4 Port 5 Port 6 Port 7 Port Termination USB3.0 Header 1 USB3.0 Header 2 USB3.0 Header 3 Not Used Port Termination USB3.0 Header 1 USB3.0 Header 2 USB2.0 Header USB to Quad UART Minicard Socket2 Minicard Socket1 / PCIe104 USB3.0 Header 3 Geode Jasper User Manual Revision A www.diamondsystems.com Page 9 of 33 3.11 SATA M.2 Socket The carrier board offers up to four SATA ports, derived from the COM express module. M.2 2242/2280 socket supports SATA Port 0 / PCIe Lane 7 using a high-speed mux. SBC provides onboard M3 4mm spacer to mount M.2 2280 SATA SSD and M3 2mm spacer acts as nut for the Male to Female 4mm spacer provided to mount M.2 2242 SATA SSD. Second SATA port (mapped as Port 1 from COM) is connected to an industry-standard vertical 7pin SATA connector that accepts cables with latching. Third SATA (mapped as Port 2 from COM) and fourth (mapped as Port 2 from COM) SATA ports are made available on the first and second minicard sockets respectively using high speed mux. PCIe/SATA interface is supported depending on the type of minicard module inserted. 3.12 PCIe104 Expansion The board offers expansion over 3 bank PCIe104 connector with 22mm stacking height. Design supports up to four, x1 lane PCIe ports on one bank PCIe104 connector and x16 PEG port on the 2nd and 3rd bank. The PCIe ports availability depends on the COM express module used. One of the USB2.0 (Port 6) is muxed with minicard2 can be selected using jumper configuration at JP3. 3.13 Digital I/O The board contains a GPIO header with 4 GPI and 4 GPO available from the COM module. GPI3 (by default) is muxed with TPM IRQ. It provides 500mA fused 3.3V supply. The GPIO signals are available on rugged circular connector J4. The system uses internally a 2x10 pin cable assembly (DSC# 6982071) to get the GPIO signals from COM carrier board to the rugged IO board. 3.14 Utility signals Power button, Reset and I2C signals are also made available on the circular connector J4. 3.15 Trusted Platform Module (TPM) The board contains Infineon's SLB 9670XQ2.0 TPM module featuring a fully TCG TPM 1.2/2.0 standard compliant module with an SPI interface. TPM can be used as a root of trust for platform integrity, remote attestation and cryptographic services. This feature will be supported based on the customer requirement and not implemented by default. Geode Jasper User Manual Revision A www.diamondsystems.com Page 10 of 33 3.16 Expansion IO Geode Osbourne also provides another rugged circular connector J6 on the enclosure. This can be used for IO expansion in future. 3.17 Data Acquisition The system provides an optional data acquisition subcircuit containing analog input, analog output, and digital I/O features. This circuit is controlled by an FPGA attached to the processor via the LPC bus. A pin header on the board provides access to JTAG signals for reprogramming the FPGA on the board and in the field. Features of the DAQ subcircuit include: 16 single-ended / 8 differential analog inputs with 16-bit resolution, programmable input ranges, and 250KSPS maximum throughput; 4 analog outputs with 16-bit resolution and programmable output ranges; and 22 digital I/O lines with selectable 3.3V/5V logic levels, selectable pull-up/down resistors, programmable direction, buffered I/O, and capability for use as counter/timer and PWM circuits. If this option is added, the signals are available on the rugged expansion IO connector J6. Geode Jasper User Manual Revision A www.diamondsystems.com Page 11 of 33 4. KEY INTERFACES The interfaces on Geode Osbourne are derived from the different subsystems. A summary of the interfaces provided on the system with its provider are tabulated below: Sl No Interface 1 HDMI 2 2x 1G Ethernet 3 4xRS-232/RS422/RS485 4 2xUSB3.2 5 2xUSB2.0 6 4xGPI + 4xGPO 7 1x SATA M.2 8 2x MiniPCIe Socket 9 PCIe104 Expansion Ports 10 AUDIO IN, OUT, MIC IN 11 1x I2C Power 12 Power Subsystem COMe Module One from COMe Module. One from WGI210IT 1G CTRLR+PHY Derived from SP336 COMe Module COMe Module COMe Module COMe Module COMe Module COMe Module+PCIe 104 Exp Board From ALC892-CG Audio CODEC COMe Module Through external power filter (JMM7515) or through onboard power filter on rugged IO board Geode Jasper User Manual Revision A www.diamondsystems.com Page 12 of 33 5. SYSTEM ARCHITECTURE Figure 1 provides an overview of the block diagrarm of the Geode Jasper system. Figure 1: System Architecture of Geode Osbourne Geode Jasper User Manual Revision A www.diamondsystems.com Page 13 of 33 6. GEODE OSBOURNE MECHANICAL DRAWING AND FEATURE LOCATIONS The form factor of the system is 9.5"x8.5"x3.85". Figure 2: Mechanical outline, front view Figure 3: Mechanical outline, top view Geode Jasper User Manual Revision A www.diamondsystems.com Page 14 of 33 Figure 4: Mechanical 3D, side view Geode Jasper User Manual Revision A www.diamondsystems.com Page 15 of 33 7. I/O CONNECTORS Following image shows the connector details on Geode Jasper system. Geode Jasper User Manual Revision A www.diamondsystems.com Page 16 of 33 7.1 J2 - Power Input (Power) Geode Jasper provides D38999 series circular connector for power input. Connector pinout is as shown below: D38999 Pin no. B C A D Signal Vin Vin Ground Ground Geode system connector Connector type Description Illustration Viewed from exterior MIL D38999/20WC4PN Shell type Straight Plug Material and finish Olive Drab Cadmium Plated Nickel Base Shell Size C Insert Arrangement C4 Contact type Pin Keying position Normal Keying Pins 4 Mating connector Connector Part# Description Illustration Viewed from exterior MIL D38999/26WC4SN Shell type Straight Plug Material and finish Olive Drab Cadmium Plated Nickel Base Shell Size C Insert Arrangement C4 Contact type Socket Keying position Normal Keying Pins 4 Geode Jasper User Manual Revision A www.diamondsystems.com Page 17 of 33 7.2 J3 IO Connector Geode Jasper provides four serial ports, Audio In, Audio Out, MIC ports and Expansion IO signals on to D38999 series circular connector. Connector pinout is as shown below: Interface Serial Port 1 Serial Port 2 Serial Port 3 Serial Port 4 Expansion IOs Geode Jasper User Manual Revision A D38999 Pin no. Signal Name 50 TX/TX_P/RX_P 49 RX/RX_P 55 RTS/TX_N/RX_N 53 CTS/RX_N 48 GND 41 TX/TX_P/RX_P 33 RX/RX_P 47 RTS/TX_N/RX_N 40 CTS/RX_N 32 GND 36 TX/TX_P/RX_P 30 RX/RX_P 29 RTS/TX_N/RX_N 37 CTS/RX_N 38 GND 46 TX/TX_P/RX_P 52 RX/RX_P 45 RTS/TX_N/RX_N 51 CTS/RX_N 39 GND 31 D_EXP_1 23 D_EXP_3 15 D_EXP_5 14 D_EXP_7 7 D_EXP_9 6 D_EXP_11 5 D_EXP_13 11 D_EXP_15 18 D_EXP_17 25 D_EXP_19 24 D_EXP_2 16 D_EXP_4 9 D_EXP_6 8 D_EXP_8 3 D_EXP_10 2 D_EXP_12 1 D_EXP_14 4 D_EXP_16 10 D_EXP_18 17 D_EXP_20 www.diamondsystems.com Page 18 of 33 Geode system connector Audio In 42 43 34 Audio Out 26 27 35 MIC In 20 13 Audio GND 21 22 No Connect 12 19 28 44 54 LINE_OUT_L LINE_OUT_R AUD_GND LINE_IN_L LINE_IN_R AUD_GND MIC_IN AUD_GND AUD_GND AUD_GND NC NC NC NC NC Connector type Description MIL D38999/20KE35BN Shell type Straight Receptacle Illustration Viewed exterior from Material and finish Shell Size Insert Arrangement Contact type Keying position Olive Drab Cadmium Plated Nickel Base E F35 Socket Normal Keying Mating connector Connector type Description Geode Jasper User Manual Revision A MIL D38999/26WE35PN Shell type Straight Plug Material and finish Shell Size Insert Arrangement Olive Drab Cadmium Plated Nickel Base E F35 www.diamondsystems.com Page 19 of 33 Illustration Viewed from rear (terminal insertion side) Contact type Keying position Pin Normal Keying Geode Jasper User Manual Revision A www.diamondsystems.com Page 20 of 33 7.3 J4 IO Connector Geode Jasper provides two 1G Ethernet, two USB2.0, GPIO, I2C and power signals on to D38999 series circular connector. Connector pinout is as shown below: Interface GBE Port 1 GBE Port2 USB2.0 Port 1 USB2.0 Port 2 D38999 Pin no. 9 8 24 16 31 39 46 52 51 55 54 53 48 47 40 32 11 10 17 18 2 1 4 5 22 19 23 13 12 14 20 Signal Name GBE0_TR0_P GBE0_TR0_N GBE0_TR1_P GBE0_TR1_N GBE0_TR2_P GBE0_TR2_N GBE0_TR3_P GBE0_TR3_N GBE1_TR0_P GBE1_TR0_N GBE1_TR1_P GBE1_TR1_N GBE1_TR2_P GBE1_TR2_N GBE1_TR3_P GBE1_TR3_N V_USB0_VBUS USB2_D2_CH_N USB2_D2_CH_P GND_DIG V_USB1_VBUS USB2_D3_CH_N USB2_D3_CH_P GND_DIG PWRBTN# M_2_MEM_ERS_GPIO RSTBTN#_3P3 GND_DIG V_3P0_RTC V_3P3_S_UTILITY I2C_CLK Geode Jasper User Manual Revision A www.diamondsystems.com Page 21 of 33 No Connect Geode system connector Connector type Description 21 I2C_DATA 25 GND_DIG 41 E_EXP_1 42 E_EXP_2 43 E_EXP_3 44 E_EXP_4 45 E_EXP_5 34 E_EXP_6 35 E_EXP_7 36 E_EXP_8 37 E_EXP_9 38 E_EXP_10 26 GND_DIG 6 NC 7 NC 15 NC 27 NC 28 NC 29 NC 30 NC 33 NC 50 NC MIL D38999/20KE35BN Shell type Straight Receptacle Material and finish Shell Size Insert Arrangement Contact type Keying position Olive Drab Cadmium Plated Nickel Base E F35 Socket Normal Keying Geode Jasper User Manual Revision A www.diamondsystems.com Page 22 of 33 Illustration Viewed exterior from Mating connector Connector type Description MIL D38999/26WE35PN Shell type Straight Plug Illustration Viewed from rear (terminal insertion side) Material and finish Shell Size Insert Arrangement Contact type Keying position Olive Drab Cadmium Plated Nickel Base E F35 Pin Normal Keying Geode Jasper User Manual Revision A www.diamondsystems.com Page 23 of 33 7.4 J7 HDMI Connector Geode Jasper provides HDMI interface signals which are terminated with SJT00RT12 series circular connector. Connector pinout is as shown below: D38999 Pin no. Signal 1 HDMI_DP2_TX0_CON_P 2 HDMI_DP2_TX0_CON_N 15 GND_DIG 3 HDMI_DP2_TX1_CON_P 4 HDMI_DP2_TX1_CON_N 16 GND_DIG 5 HDMI_DP2_TX2_CON_P 6 HDMI_DP2_TX2_CON_N 17 GND_DIG 9 HDMI_DP2_TX3_CON_P 10 HDMI_DP2_TX3_CON_N 19 GND_DIG 20 HDMI_CEC_CON NC 12 HDMI_SCL_CON 13 HDMI_SDA_CON 14 GND_DIG 21 V_5P0_HDMI 7 HDMI_HPD_CON 22 GND_DIG 8 NC 11 NC 18 NC Geode System connector Connector type Description Illustration Viewed from exterior MIL SJT00RT12-35S014 Shell type Straight Receptacle Material and finish Olive Drab Cadmium Plated Nickel Base Shell Size 12 Insert Arrangement 12-35 Contact type Female Socket Keying position Normal Keying Pins 22 Geode Jasper User Manual Revision A www.diamondsystems.com Page 24 of 33 Mating connector Connector type Description Illustration Viewed from rear (terminal insertion side) MIL SJTG06RT12-35DP014 Shell type Straight Plug Material and finish Olive Drab Cadmium Plated Nickel Base Shell Size 12 Insert Arrangement 12-35 Contact type Pin Keying position Normal Keying Pins 22 7.5 J5 USB3.2 Connector Geode Jasper provides 2xUSB3.2 interface signals which are terminated with SJT00RT12 series circular connector. Connector pinout is as shown below: USB Port# D38999 Pin no. Signal 1 USB3_VBUS 7 USB D- 8 USB D+ 2 GND USB3.0 Port 1 5 USB3_SSRX- 6 USB3_SSRX+ 16 GND 3 USB3_SSTX- 4 USB3_SSTX+ 14 USB3_VBUS 22 USB D- 18 USB D+ 13 GND USB3.0 Port 2 11 USB3_SSRX- 12 USB3_SSRX+ 19 GND 9 USB3_SSTX- 10 USB3_SSTX+ Geode system connector Connector type Description Geode Jasper User Manual Revision A MIL SJT00RT12-35S014 Shell type Straight Receptacle Material and finish Olive Drab Cadmium Plated Nickel Base www.diamondsystems.com Page 25 of 33 Illustration Viewed from exterior Shell Size Insert Arrangement Contact type Keying position Pins 12 12-35 Female Socket Normal Keying 22 Mating connector Connector type Description Illustration Viewed from rear (terminal insertion side) MIL SJTG06RT12-35DP014 Shell type Straight Plug Material and finish Olive Drab Cadmium Plated Nickel Base Shell Size 12 Insert Arrangement 12-35 Contact type Pin Keying position Normal Keying Pins 22 7.6 J2 - I/O Connector The 1G Eth, 2x CAN, DIO, Audio, 4x Serial ports, 2x USB2.0 and Control Signals of the Geode System are terminated with a D38999 series circular connector. The connector pinouts are as shown below: Geode Jasper User Manual Revision A Port Type 1G Ethernet Port D38999 Pin no. 10 4 17 25 Signal GBE0_TR0_P GBE0_TR0_N GBE0_TR1_P GBE0_TR1_N www.diamondsystems.com Page 26 of 33 1 GBE0_TR2_P 5 GBE0_TR2_N 2 GBE0_TR3_P 3 GBE0_TR3_N 64 USB VBUS 66 USB2 Port 1 65 USB DUSB D+ 62 GND 44 USB VBUS 51 USB2 Port 2 43 USB DUSB D+ 58 GND 11 TX/TX_P/RX_P 13 Serial Port 1 (RS232/RS422/RS485) 12 14 RX/RX_P RTS/TX_N/RX_N CTS/RX_N 15 GND_DIG 16 TX/TX_P/RX_P 19 Serial Port 2 (RS232/RS422/RS485) 9 20 RX/RX_P RTS/TX_N/RX_N CTS/RX_N 21 GND_DIG 35 TX 36 RX Serial Port 3 (RS232) 38 RTS 37 CTS 39 GND 41 TX Serial Port 4 (RS232) 40 RX 42 GND 45 SYS_RST_IN_N Power Signals 47 BUTTON_POWER_ON_N 50 FORCE_RECOVERY 48 MEM_ERS 52 I2C_CLK_3P3 I2C Signals 53 I2C_ DAT_3P3 6 CAN0_H 23 CAN Signals 7 CAN1_L CAN0_L 22 CAN1_H 34 DIO_PA0 26 DIO_PA1 DIO Signals 27 DIO_PA2 28 DIO_PA3 29 DIO_PA4 Geode Jasper User Manual Revision A www.diamondsystems.com Page 27 of 33 30 31 32 57 63 Audio Signals 56 61 60 +5V 54 8 46 49 Ground 55 24 33 59 No Connect 18 DIO_PA5 DIO_PA6 DIO_PA7 AUDIO_OUT_L AUDIO_OUT_R GND_AUD AUDIO_MIC_IN GND_AUD V_5P0 GND GND GND GND GND GND GND NC Geode system connector Connector type Description MIL D38999/20WF35SN Shell type Straight Receptacle Illustration Viewed exterior from Material and finish Shell Size Insert Arrangement Contact type Keying position Olive Drab Cadmium Plated Nickel Base F F35 Socket Normal Keying Mating connector Connector type Description Geode Jasper User Manual Revision A MIL D38999/26WF35PN Shell type Straight Plug www.diamondsystems.com Page 28 of 33 Illustration Viewed from rear (terminal insertion side) Material and finish Shell Size Insert Arrangement Contact type Keying position Olive Drab Cadmium Plated Nickel Base F F35 Pin Normal Keying Geode Jasper User Manual Revision A www.diamondsystems.com Page 29 of 33 8. GEODE JASPER JUMPER CONFIGURATIONS 8.1 Jumpers on Jasper COM Carrier Board The Jumper blocks on the Jasper COM carrier board can be configured to enable/disable or alter the default signal routing settings on the circuit, using Jumper shunts. Figure 4: Jumper Blocks on Jasper Carrier Board The following table describes the Jumper Blocks on the carrier board. Name Function JP1 FPGA address selection JP2 LVDS_BKLT and LVDS_VDD voltage level selection JP3 USB TO MPCIE/PCIE/104, input voltage selection JP4 Serial port mode selection JP5 DIO Voltage and PU/PD selection JP6 Serial Port 3 & 4 termination selection JP7 Serial Port 1 & 2 termination selection Geode Jasper User Manual Revision A www.diamondsystems.com Page 30 of 33 8.2 Jumper Block JP1 JP1 Jumpers Configuration are provided to set the address of the FPGA. Position Function A0 FPGA Address 0 A1 FPGA Address 1 A2 FPGA Address 2 A3 FPGA Address 3 *Default Address = 0x240 IN OUT Refer following table Refer following table Refer following table Refer following table FPGA Addresses FPGA Address FPGA Address - 0X100 FPGA Address - 0X120 A0 A1 IN IN IN IN FPGA Address - 0X140 IN IN FPGA Address - 0X180 IN IN FPGA Address - 0X200 IN OUT FPGA Address - 0X240 IN* OUT* FPGA Address - 0X280 IN OUT FPGA Address - 0X2C0 IN OUT FPGA Address - 0X300 OUT IN FPGA Address - 0X340 OUT IN FPGA Address - 0X380 OUT IN FPGA Address - 0X3C0 OUT IN FPGA Address - 0X400 OUT OUT FPGA Address - Reserved OUT OUT FPGA Address - Reserved OUT OUT FPGA Address - Reserved OUT OUT *Default Mode A2 IN IN OUT OUT IN IN* OUT OUT IN IN OUT OUT IN IN OUT OUT A3 IN OUT IN OUT IN OUT* IN OUT IN OUT IN OUT IN OUT IN OUT Note: 1. Base address must be selected based on COM module used with Jasper. 2. Whiskey Lake COM supports 0x240 and 0x280 base address. 3. Tiger Lake COM supports 0x240 base address. Geode Jasper User Manual Revision A www.diamondsystems.com Page 31 of 33 8.3 Jumper Block JP2 JP2 Jumpers are provided to select the voltage level of the LVDS display and backlight. The configuration is as shown below: Position Function IN 12V LCD Backlight Voltage 5V LCD Backlight Voltage 12V* 5V 5V LCD VDD Voltage 5V 3V3 LCD VDD Voltage 3.3V* *Default Mode Note: Make sure 5V and 3V3 Jumper are not IN at same time. OUT - 8.4 Jumper Block JP3 JP3 Jumpers Configuration are provided select the configuration pins of the FPGA, USB interface and Power IN option. USB interface from COMe Type AB connector is multiplex to mPCIe and PCIe/104 connector. Board can be powered with 18V-36V wide input or 12V fixed supply. Position Function U0 FPGA Config 0 U1 FPGA Config 1 USB USB SEL 12VIN Wide Input SEL *Default Mode IN OUT TBD TBD TBD* TBD* Minicard PCIe104* 12V Fixed Wide Input* 8.5 Jumper Block JP4 JP2 Jumpers are provided to select the mode of serial ports 1, 2, 3 & 4. SC0 and SC1 jumpers are used to select mode for serial ports 1 & 2 and SC2 and SC3 jumpers are used to select mode for serial ports 3 & 4. The configuration is as shown below: Port Position RS232 RS485 RS422 SC0 1&2 SC1 1&2 IN* OUT* OUT IN OUT OUT SC2 3&4 IN* OUT OUT SC3 3&4 OUT* IN OUT *Default Mode Note: Make sure 5V and 3V3 Jumper are not IN at same time. Internal Loop IN IN IN IN Geode Jasper User Manual Revision A www.diamondsystems.com Page 32 of 33 8.6 Jumper Block JP5 JP2 Jumpers are provided to select the voltage level and Pullup/pull down configuration of the DIO. By default, the DIOs are 3.3 Volare pulled down. The configuration is as shown below: Position Function IN OUT 5V DIO Voltage Level 3V3 DIO Voltage Level 5V 3.3V* PU DIO Pull up Enable Enabled Disabled PD DIO Pull down Enable Enabled* Disabled *Default Mode Note: Make sure 5V and 3V3 Jumper are not IN at same time. 8.7 Jumper Block JP6 JP2 Jumpers are provided to enable and disable the termination of serial ports3-4. The configuration is as shown below: Position Function TX3 Serial Port3 TX Termination RX3 Serial Port3 RX Termination TX4 Serial Port4 TX Termination RX4 Serial Port4 RX Termination *Default Mode IN OUT Enabled Disabled* Enabled Disabled* Enabled Disabled* Enabled Disabled* 8.8 Jumper Block JP7 JP2 Jumpers are provided to enable and disable the termination of serial ports1-2. The configuration is as shown below: Position Function TX1 Serial Port1 TX Termination RX1 Serial Port1 RX Termination TX2 Serial Port2 TX Termination RX2 Serial Port3 RX Termination *Default Mode IN OUT Enabled Disabled* Enabled Disabled* Enabled Disabled* Enabled Disabled* Geode Jasper User Manual Revision A www.diamondsystems.com Page 33 of 33