DALCNET MINI-1AC LED Dimmer Parameters Directly Programmable Owner’s Manual
FEATURES
- AC DIMMER + FADER
- Brightness adjustment of WHITE and MONOCHROME light
- Power supply (AC IN): 230 Vac @ 50 Hz, with internal 1 A fuse
- Output (AC OUT): 230 Vac Trailing Edge (350 W max), for incandescent and halogen lamps, LED switching lamps, strip and linear LED lamps, dimmable Trailing Edge drivers
- Local Command (PUSH): N° 1 N.O. push-butto
- Remote control: via Bluetooth Low Energy (BLE) with CASAMBI© mobile app
- Device configuration via CASAMBI© mobile application, parameters can be set (via Fixture):
- Dimming curve
- Max and min brightness levels
- Memory function: stores the last brightness level set
- ON/OFF and brightness soft dimming
- Suitable for use in Dry locations
- Typical efficiency > 95%
- Extended temperature range
- 100% Functional Test
PRODUCT DESCRIPTION
MINI-1AC-CASAMBI is a single-channel Alternating Current (AC) Trailing Edge dimmer, which can be supplied by 230 Vac mains
power grid and is suitable for driving single-color AC loads such as incandescent and halogen lamps, LED switching lamps, LED
strips/lamps and dimmable drivers in Trailing Edge mode.
The AC dimmer is equipped with an internal 1 A fuse, protecting the internal circuitry, which makes the installation of an external
fuse optional. The maximum output current is 1.52 A and has the following protections: input fuse protection, output short-circuit
protection, short-circuit detection, and output open-circuit detection.
MINI-1AC-CASAMBI can be controlled remotely via Bluetooth or locally via N.O. (Normally Open) button connected to the phase,
neutral or as a dry contact. The type of wiring is recognized when it is turned on and the dimmer is automatically configured to
work with the control connected.
MINI-1AC-CASAMBI enables you to make not only simple brightness adjustments but also more dynamic lighting control systems.
This is made possible through the creation of multiple scenarios, animations, timers, daylight controls, and more.
Through the CASAMBI© mobile application and smartphones equipped with Bluetooth technology, it is possible to configure via
Fixtures multiple parameters, including maximum/minimum brightness levels. CASAMBI© mobile application can be downloaded
free of charge from the Apple APP Store and Google Play Store.
CASAMBI© Mobile App is free to download from the Apple APP Store and Google Play Store
⇢ For the up-to-date manual, please consult our website www.dalcnet.com or scan the QR Code on product label.
PRODUCT CODE
| CODE | POWER SUPPLY | OUTPUT LED | N° OUTPUTCHANNEL | REMOTECONTROL | LOCALCONTROL | APP CONFIG |
| MINI-1AC-CASAMBI | 230 Vac @ 50 Hz | 1 x 1.52 A1 | 1 | Bluetooth LowEnergy (BLE) | Pushbutton N.O.2 | CASAMBI©mobile app |
PROTECTIONS AND DETECTION
The following table shows the types of ingress and egress protection/detection present on the device.
| ACRONYM | DESCRIPTION | TERMINAL | PRESENT |
| IFP | Input Fuse Protection1 | AC IN | ✔ |
| SCP | Short-Circuit Protection3 | AC OUT | ✔ |
| SCD | Short-Circuit Detection | AC OUT | ✔ |
| OCD | Open-Circuit Detection | AC OUT | ✔ |
REFERENCE STANDARDS
MINI-1AC-CASAMBI complies with the regulations listed in the following table.
| STANDARD | TITLE |
| EN 55015 | Limits and methods of measurement of radio disturbance characteristics of electrical lighting andsimilar equipment |
| EN 61547 | Equipment for general lighting purposes – EMC immunity requirement 4 |
| EN 61000-3-2 | Electromagnetic compatibility (EMC) – Part 3-2: Limits – Limits for harmonic current emissions(equipment input current ≤ 16 A per phase) 4 |
| EN 61000-3-3 | Electromagnetic compatibility (EMC) – Part 3-3 Limits – Limitation of voltage changes, voltage fluctuations and flicker in public low-voltage supply systems, for equipment with rated current ≤ 16A per phase and not subject to conditional connection 4 |
| EN 61347-1 | Lamp Controlgear – Part 1: General and safety requirement |
| EN 61347-2-11 | Lamp controlgear – Part 2-11: Particular requirements for miscellaneous electronic circuits used withluminaires |
- The maximum output current depends on the operating conditions and ambient temperature of the system. For the correct configuration, check the maximum power that can be delivered in the §Technical specifications section and in the §Thermal Characterization.
- The detection of the type of wiring is done automatically.
- Short Circuit Protection (SCP) is disabled by default. It is recommended to enable this function only on compatible load types (see Table 5) on the dedicated CASAMBI© mobile app section.
- Compliance with EMC standards is achieved in worst-case (nominal load 200 W) by application in a suitable inlet filter.
- For the full range of values, refer to the §Thermal Characterization of the manual.
- The parameters are derived from the configuration of the Casambi module.
- Tamb_max: depends on ventilation conditions
MINI-1AC-CASAMBI
TECHNICAL SPECIFICATIONS
| Description Acronym Values Units of Note
Min Max Measure |
|||||||||
| INPUT (AC IN Power) | |||||||||
| Nominal Supply Voltage | VIN | 230 | Vac | – | |||||
| 210 ÷ 240 | Vac | – | |||||||
| Supply Voltage range | VIN-ANG | ||||||||
| Mains Frequency | Mum | 50 | Hz | – | |||||
| Efficiency at full load | Err | > 95 | A % | – | |||||
| Standby power absorption | Psray | < 0.5 | W | – | |||||
| OUTPUT (AC OW Channel) | |||||||||
| Output Voltage | Vour | = Via | Vac | – | |||||
| Output currents (max) | Iatrr | 1.52 | A | – | |||||
| Nominal power outputMinimum load power Load typeDimming curve | Pour | 350 | W | Dependent on the type of load connected, see Table 5 | |||||
| PMDALOAD Lflpf CortiI |
1 –See Table 5DIMMINGLinear• Logarithmic | W– – |
– | ||||||
| –* Available only for Local Command | |||||||||
| Dimming method | MINN Trailing Edge | – | – | ||||||
| Dimming resolution | Res/mm 1666 1000 | step | Defined by project | ||||||
| Dimming range | RNGoin 5 ÷ 100 | % | Dependent on the type of connected load | ||||||
| ENVIRONMENTAL | |||||||||
| Operating Frequencies 6 fop 2402 + 2483 | MHz dBmW |
For CASAMBI° BLE SoC Over Bluetooth transmission | |||||||
| Maximum Emitted Power 6 7 | |||||||||
| Storage Temperature TSTG:tE -40 + +60 | °CMinimum values defined by design | ||||||||
| Working Ambient temperature 5‘7 TA –10 + +60 °C | |||||||||
| Max Temperature ©T, point Tc – – +80 °C – | |||||||||
| WSsouo 0.05 + 2.5 mm2 | Defined byproject | ||||||||
| Wiring SectionWSSTRAND 30 ÷ 12 I AWGStrip length WSSTR1P 6.5 mm | —– | ||||||||
| Protection class i Casing Material Packaging unit | IPcco€MuseUP | 1P20 I -PlasticI –1 pcsL A P | |||||||
| Dimensions | MD | 44 57 25 I mm | Casing | ||||||
| PD | 56 68 35 I mm | Packaging | |||||||
| Weight | W | 80 I g | – | ||||||
TYPE OF LOAD
The following table shows the types of loads that can be connected to the output of the MINI-1AC-CASAMBI.
| Load | Description | Maximum Power [IN] 250 | I SCP Compatibility✓(< 100 VV) | |||
| Incandescent lamps / Halogen | ||||||
| in | Linear LED Mains Voltage Lamps | 350 | ✓ | |||
| 1117 | ||||||
| LED switching lamps at mains voltage | 300 | ✓ | ||||
| LED Strips / Mains Voltage LED Modules | 350 | ✓ | ||||
| count tkrxxxo1 |
||||||
| :I.rs4 | ||||||
| i si 23/4″ a WAAL LEDDRIVER | Dimmable LED Trailing Edge Drivers | 250 | ✓(< 100 W) | |||
Documents / Resources
 |
DALCNET MINI-1AC LED Dimmer Parameters Directly Programmable [pdf] Owner's Manual MINI-1AC LED Dimmer Parameters Directly Programmable, MINI-1AC, LED Dimmer Parameters Directly Programmable, Dimmer Parameters Directly Programmable, Parameters Directly Programmable, Directly Programmable, Programmable |