Creality HALOT-LITE 3D Printer User Manual

HOT -LITE
V1.4  3D Printer User Manual

Dear Consumers,

Thank you for choosing our products. For the best experience, please read the instructions before operating the Printer. Our teams will always be ready to render you the best services. Please contact us via the phone number or e-mail address provided at the end when you encounter any problem with the Printer. For a better experience in using our  product, you can also learn how to use the printer in the following ways:
View the accompanying instructions and videos on the U disk.
Visit our official website www.creality.com to find relevant software/hardware information, contact details, and operation and maintenance instructions

Firmware Upgrade
Please login to the official website https://www.creality.com/download, switch the language, select the relevant printer and model and download the required firmware, you can use it after the installation is finished

NOTES

1. Do not use the printer in any way other than described here in order to avoid personal injury or property damage.
2. Do not place the printer near any heat source or flammable or explosive objects. We suggest placing it in a well-ventilated, low-dust environment.
3. Do not expose the printer to violent vibration or any unstable environment, as this may cause poor print quality.
4. Please use recommended resin to in case damage of to the machine.
5. Do not use any other power cable except the one supplied. Always use a grounded three-prong power outlet.
6. Please do not open the plastic cover during usage, otherwise, the printing will be interrupted.
7. Do not wear cotton gloves when operating the printer. Such clothes may become tangled in the printer’s moving parts leading to burns, possible bodily injury, or printer damage.
8. Please wait a moment after the print is finished. And please wear gloves to take out the print by tools.
9. Clean the printer frequently. Always turn the power off when cleaning, and wipe with a dry cloth to remove dust, adhered printing plastics, or any other material on the frame, guide rails, or wheels. Use glass cleaner or isopropyl alcohol to clean the print surface.
10. Children under 10 years should not use the printer without supervision.
11. Tips：Do not plug or unplug the power cord when power on.
12. Users should comply with the laws and regulations of the corresponding countries and regions where the equipment is located (used), abide by professional ethics, pay attention to safety obligations, and strictly prohibit the use of our products or equipment for any illegal purposes. Creality will not be responsible for any violators’ legal liability under any circumstances

Introduction

1 Protective cover 2 Limit switch 3 Hexalobular socket screw 4 Leveling screw

5 Building platform 6 Hexalobular socket screw 7 Resin vat 8 Touch screen

9 USB port 10 Power socket

Equipment parameters

	Basic Parameters
Model Name	HALOT-LITE
Build Size	192*120*200mm（length, width, and height）
XY Axis Resolution	3840*2400
XY Axis Accuracy	0.05mm
Print speed	1-4S/layer
Layer Thickness	0.01-0.2mm
Touch Screen	5-inch touch screen
Light Source Type	Integral light source (wavelength 405nm)
Rated Voltage	100-240Va.c, 50/60Hz
Rated Power	250W
Machine Size	330*301*572mm
Package size	425*393*685mm
Net Weight	10.6KG
Gross Weight	13.5KG
Print Method	USB Disk, Creality Cloud
Machine Language	English
Slicing Software Operation System	Win7/Win8/Win 10 64bit, Mac system (32-bit is not supported)
Compatible Resin	Common rigid photosensitive resin, Standard resin, Hight hardness, High toughness, Dental model resin.

Package Content

Tips: the above accessories are for reference only, in kind prevail!

Interface Information

Note: The current interface is for reference only, due to the continuous upgrading of functions, the actual to the official website of the latest firmware UI as the standard.

Note: The current interface is for reference only, due to the continuous upgrading of functions, the actual to the official website of the latest firmware UI as the standard.

Level Platform

Note: The printing platform has been leveled at the factory. If it needs leveling due to transportation or other reasons, please follow the steps below to adjust the printing platform.

1. To calibrate the printing platform, first raise the platform, loosen the fixing screws on the left and right sides of the material trough, and take out the material trough;
2. Loosen the four Leveling screws of the prototyping platform, attach the Calibration card tightly to the print screen, and press Settings → Z-Axis Motion → Levelling（Refer to operating steps of leveling platform 2 for operation.）, to check whether the platform fits evenly with the paper.
3. after confirming that the Calibration card fits evenly with the platform, screw up

Note: The current interface is for reference only, due to the continuous upgrading of functions, the actual to the official website of the latest firmware UI as the standard.

Load Resin

Pour the UV photosensitive resin into the resin vat. The slot capacity is 500ml/1000ml.

Tips：
Take out the resin vat slowly, pour out the remaining resin into the container, clean the resin vat, pour in new resin, and then install the resin vat on the machine. How to change resin:

Caution： Resin may cause skin irritation or an allergic skin reaction. Please wear gloves before use to avoid direct contact with the skin.

Release Film Instructions

Installation steps
a. First, remove the 14 screws at the bottom of the vat and take down the old release film.
b. Prepare the new release film, peel off the protective films on both sides of the release film. Align the holes and fit the release film on the clamping ring.
c. Finally, place the film-ring assembly back into the vat frame gently, then install and tighten the fixing screws diagonally.
d. The installed release film is as shown.

Start Printing

Slicer

.1 the left of the screen and add model file.  eat nepO slicer kcilc ,retnirp D3 DCL fo erawtfos no ”nepo“	2. If the model needs to add support, click the upper-left icon to set corresponding parameters.
3. Click icon ①→Setting slice printing parameters②→ ”evil“ kill	4 waiting for a slice to be finished-*save the sliced file You are welcome to find more details of the slicing tutorial on the official website www.creality.com).

 Print

1. Generate cxdlp file， and save the file to U disk.	2. Insert the U disk → press the print button.

Warning: During the printing process, the machine can not be shaken, so as not to affect the printing quality.

1. Select files;	2. Select the file to be printed and press “Start”;	3. Printing• • •

Control remote printing

Wiring Connection

Troubleshooting

FCC Statement

FCC Caution:
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
IMPORTANT NOTE:
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the  user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with a minimum distance of 20cm between the radiator& your body.

IC Caution:

This device complies with Industry Canada’s license-exempt RSS. Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of the device.
To maintain compliance with RF exposure guidelines, this equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.
Due to the differences between different machine models, the physical objects and the final images can differ. The final explanation rights shall be reserved by Shenzhen Creality 3D Technology Co., Ltd.

https://qr.creality.com

SHENZHEN CREALITY 3D TECHNOLOGY CO., LTD.
Add:18F, JinXiuHongDu Building, Meilong Blvd., Longhua Dist.,
Shenzhen, China 518131
Official Website: www.creality.com
Tel：+86 755-8523 4565
E-mail: info@creality.com
cs@creality.com