CREALITY HyperFeed Combo 3D Printer User Guide

Technical Parameters

Component Introduction

List of Accessories

Quick Installation Guide

Unpack the equipment and accessories
Unpack the box, take out the HyperFeed and its accessories, and check to make sure all the accessories are included.

Unfold the base
Place the HyperFeed flat on the desk and unfold the base downward.

Install the piping assembly (HALOT-X1 Max)
Warning: Before installation, home the printer’s light source assembly, remove the resin vat and build plate, and disconnect the power supply.

Note: Before installing the piping components, please completely cover the print screen with a piece of cardboard or foam of the appropriate size to prevent scratches or impacts to the print screen during installation.

Connect the piping

Connect the 6-pin control cable

Warning: Do not hot-swap the 6-pin control cable! Be sure to disconnect the printer from the power source before plugging or unplugging the cable.

Install the bucket

1. Apply the RFID tag
   For HALOT resin, peel the bottom RFID label and stick it inside the resin bucket.
2. Install the resin bucket
   Align the interface, hold the resin bucket with both hands, and press it vertically into the HyperFeed main unit.
3. Install the resin bucket suction tube
   Align the straw with the bottom groove and insert it.
4. Apply labels
   Write the resin name on the label, and apply it to the designated location on the resin bucket.

Note: When installing the suction tube, check that the lower opening is vertical or within the stop frame.

First-Time Use

1.  Add the resin
   • Pour the resin along the edge; (Please do not exceed Max level. The max volume is 5L)
   • Install the resin bucket lid and snap the latches on both sides into place. The resin can be stored for long periods.
2. Connect the printer
   • When the printer is turned on, the HyperFeed indicator lights up green;
   • Swipe left on the printer’s home screen to bring up the HyperFeed home screen; this indicates a successful connection.

Note: If the HyperFeed indicator light is off, the printer’s home screen does not respond when swiped to the right, or the printer is malfunctioning, please try restarting the printer or repeating the installation steps.

Operating Mode

1. Manual Control
   Select [HyperFeed] in [Print Control] to configure spool heating and manually feed or retract filament.
2. Automatic Control
   Go to the slicing file page and enable the [Auto-feed] and [Bucket heating] functions.

Clean the Piping / Replace the Resin

• Connect the end of the cleaning tube assembly with the fitting to the HyperFeed, and place the other end into a container filled with alcohol.
• Navigate to [ Print Control ] → [ HyperFeed ], then tap [ One-click Cleaning ] and follow the on-screen instructions.
• When the screen displays “Auto cleaning completed!”, tap Done and remove the cleaning tube assembly.

• Warning: Before starting, unload the material, drain any remaining resin from the vat, and remove the old resin bucket.
• Tip: We recommend using 1,000 mL of alcohol. Please wear protective gloves while cleaning.

Status Indicator Light

•  Off
•  Solid Green
•  Flashing Green
• Solid Red

Compliance and Regulatory Information

IC ID Requirement
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:

• This device may not cause interference;
• This device must accept any interference, including interference that may cause undesired operation of the device.

The device meets the exemption from the routine evaluation limits in issue 6 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and compliance.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.

NFC Function Description
HyperFeed (the feeding module) obtains the resin parameters by reading data from the NFC chip on the resin container, and uploads the data to the HALO-X1 Max (3D printer) via a serial port. The 3D printer then sets the printing parameters based on the resin parameters.

FCC Requirement
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

• This device may not cause harmful interference;
•  This device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

 This product is designed for indoor use only.