2565 Parcel Dimensioner
Quick Start Guide
The 2565 Parcel Dimensioner is a compact, robust, and intuitive handheld device designed for multi-dimensional measurement, capable of measuring the length, width, and height of cuboid parcels. The 2565 Parcel Dimensioner features intelligent reading zone detection and a laser guiding aimer, allowing users to perform quick and accurate measurements.
Open Your Box
2565 Parcel Dimensioner
2565 Parcel Dimensioner Cradle
2565 Parcel Dimensioner Quick Start Guide
Battery
AC Adapter
USB Cable x2 (Connect to a PC)
Overview

Set up the Device
Step 1: Place the battery.
Step 2: Cover the battery lid.
Step 3: Fix the screw.
Step 4: Connect the adapter to the cradle and the socket.
Step 5: Position the 2565 on the cradle for charging.

Data Display
To promptly view the parcel dimensions (Width/Height/Length) read by the 2565, download and launch the “DimenMobile” app on your mobile device. Then, follow the instructions below under “Bluetooth Connection” to pair with the 2565 by scanning the QR Code on its side. Once successfully paired, you can view the reading information from the 2565 on your mobile device using the “DimenMobile” app.

For more details about “DimenMobile”, please refer to 2565 Parcel Dimensioner User Guide.
『Dimen Mobile』
Bluetooth Connection
QR Code Scan-to-Pair

You can easily connect the 2565 to your mobile computer by scanning the QR Code. (using the RS38 mobile computer as an example):
- Download and launch the “DimenMobile” app on your mobile computer.
- Align the RS38’s scan window with the QR code on the side of the 2565, then push the side trigger to scan. Alternatively, you can tap the “
” icon in the app to use the camera for scanning. - When the connection is established, the 2565 will emit a series of beeps.
Note:
Scanning the QR Code with the reader and trigger button is exclusive to CipherLab mobile computers.
Measurement Methods
There are 2 measurement methods: Pitch Scan and Vertical Scan.
Pitch Scan
Scanning the side edge of a parcel horizontally.

Adjust the distance until the “+” laser targets the center of the front-upper edge (F-Edge). Ensure the horizontal line matches or exceeds the F-Edge width, with the vertical line centered.
Vertical Scan
Scanning the top surface of a parcel placed upright.

Adjust the distance until the “+” laser targets the center of the parcel. When the “+” laser spans the parcel’s width and aligns centrally above it, dimensions will be measured instantly.
Pitch Scan

The optimal reading distance is 40cm to 150cm from the surface of the parcel, with a pitch angle of 35º to 65º and a skew angle of plus/minus ±7º.

Vertical Scan

The optimal reading distance is 40cm to the upper surface of the parcel, within 150cm from the ground. Maintain a vertical orientation with a pitch angle of ±10°.
Button Functions
The 2565 features 2 primary buttons:
Settings Button on the top and the Trigger on the grip.
Please refer to the table below for their respective functions.

Button Functions
| Action | Description |
| Press and Hold the Settings Button for 5 Seconds | Disconnect |
| Single Press the Trigger | Starts Dimension Measurement |
| Press and Hold the Settings Button then the Trigger for 5 Seconds | Reset to Default Settings |
FCC 15.19
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC 15.21:
The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
FCC 15.105
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RF Exposure Warning!
This device contains transmitters and receivers which emit Radio Frequency (RF) energy.
The device is designed to comply with the limits for exposure to RF energy set by the Federal Communications
Commission (FCC) of the United States,
Industry Canada (IC) of Canada, and the regulating entities of other countries.
To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user’s authority to operate the device.
P/N: S2565AQG01001
CipherLab Europe Representative Office.
Cahorslaan 24, 5627 BX Eindhoven, The Netherlands
Tel: +31 (0) 40 2990202
Copyright©2024 CipherLab Co., Ltd.
Documents / Resources
![]() | 2565 Parcel Dimensioner |
References
- User Manualmanual.tools
