bouncepad BP-COR-S60 Core Static 60 Tablet Stand Installation Guide
bouncepad BP-COR-S60 Core Static 60 Tablet Stand

Core Static 60

Assembly Instructions

Tools Required: 

  • Pencil
  • Electric Drill
  • 7mm Spanner
    *or adjustable spanner
  • 5.0mm Drill bit
    *if fixing from below
  • 2.5mm Drill bit
    *if fixing from above
    16mm
    *if routing the tablet cable through your mounting surface
  • Hole saw
  • Socket Driver

Sheet Code: BP-IM-080_REV1
Release Date: 06/08/2024

Copyright 2024 Spot spot Ltd. (T/A Bounce pad) all rights reserved.
Confidential, no part of this publication may be reproduced or transmitted in any form without the written permission of the copyright holder.

In the Box

What's In Box

Flat Cable
What's In Box
Fixings Kit
What's In Box
Tablet Mount Plate
Shell
What's In Box
Static60 Mounting Arm
What's In Box
Surface Mounting Kit
What's In Box

Fixings List

Fixings List

* Due to the modular nature of our product range you may receive additional fixings in the fixings kit

4x No.8 Countersunk Self tapping Screw
Fixings List
4x M4x40mm Socket setscrew
Fixings List
4x M4x10mm Countersunk Screw
Fixings List
4x M4x16mm Buttoned screw
Fixings List
4x M4 Wing Nut
Fixings List
2x 3mm x 6mm Pan Head Screws
Fixings List
4x M3x10mm Countersunk Screw
Fixings List
1x Cable Clamp
Fixings List
1x T20 Pin Torx Driver Bit
Fixings List
1x Mount Washer
Fixings List
1x Case Washer
Fixings List
8x M4 Split Washer
Fixings List
4x M4 Locking Nut
Fixings List
1x Cleaning Wipe
Fixings List
1x T10 Pin Torn Allen Key
Fixings List

A Follow steps A if “Fixing from below”.
Installation Instruction
B Follow steps B if “Fixing from Above”.
Installation Instruction
A1 Using the Mount washer, mark the drill hole locations.
Installation Instruction
A2 Drill each hole – using the specified drill.
Installation Instruction
A3 Locate and screw the Socket screws into the Desk as shown.
Installation Instruction
A4 Secure the arm to the surface. Locking Nuts offer higher security.
Installation Instruction
A5 Go to step 1.
Installation Instruction
B1 Using the Mount Plate, mark the drill hole locations as shown.
Installation Instruction
B2 Drill each hole – using the specified drill sizes.
Installation Instruction
B3 Locate the Cover onto the Static60.
Installation Instruction
B4 Join the Static60 & Mount Plate in the orientation shown.
Installation Instruction
B5 Secure the Static60 to the surface with the 4x countersunk fixings.
Installation Instruction
B6 Adhere the Mount Cover onto the Mount Plate with the adhesive tabs.
Installation Instruction
B7 Go to step 1.

  1. Locate & attach the Shell to the Static 60 in the correct orientation.
    Installation Instruction
  2. Remove the Mounting Plate adhesive backing. Attach level & centrally to the Tablet back as shown.
    Installation Instruction
  3. Attach the Flat Cable to the Tablet with the U-Bend Head.
    Installation Instruction
  4. Secure the Flat Cable to the Mounting Plate with the Cable Clamp as shown.
    Installation Instruction
  5. Remove the Fixing Covers. Feed the Flat Cable into the assembly & locate the Tablet in the chosen orientation.
    Installation Instruction
  6. Secure the Tablet to the Shell & attach the Fixing Covers as shown.
    Installation Instruction
  7. Connect tablet to power & installation is now complete.
    Installation Instruction

Company Logo

Documents / Resources

bouncepad BP-COR-S60 Core Static 60 Tablet Stand [pdf] Installation Guide
BP-COR-S60 Core Static 60 Tablet Stand, BP-COR-S60, Core Static 60 Tablet Stand, Static 60 Tablet Stand, Tablet Stand, Stand

References

Leave a comment

Your email address will not be published. Required fields are marked *