User Manual: Headphones
Model: T5

Headphones Overview

Headphones Overview

Operating instructions

Power on:
Press and hold the MF button until you hear “Power on”.

Power off:
Press and hold the MF button until you hear “Power off’.

Pairing mode:
When the headphones are off, press and hold the MF button until you hear “Ready to pair”.

Bluetooth pairing:
Make the headphones enter pairing mode (see instruction “Pairing mode”), and turn on the Bluetooth feature of your phone, select “Bluedio T 5th”.

Music control:
When playing music, press the Pause/Play button once to Pause; press once again to resume.

Volume- button:
Press once to reduce the volume; press and hold to skip to the previous track.

Volume+ button:
Press once to increase the volume; press and hold to skip to the next track.

Answer/Reject phone calls:
Receiving an incoming call, press the MF button once to Answer; press once again to End; Press and hold for 2 seconds to refuse.

Active noise cancelling:
Push the ANC switch to turn on/off the ANC function; when it’s on, the green light will stay on.

Language selection:
Turn on the headphones first, then press the MF button and the Volume- button once simultaneously to select Chinese/English/French/Spanish.

Redial the last number:
Press the MF button twice to redial the last number.

Switch phone calls:
Receiving Call 2 in Call 1, press and hold the MF button to hold on Call 1 and answer Call 2; press and hold again to switch back to Call 1; press once to end the call.

Connect to two mobile phones via Bluetooth:

Connect to two mobile phones via Bluetooth
  1. Connect T 5th with phone 1, then turn off T 5th and the Bluetooth feature of phone 1.
  2. Tum on T 5th and make it enter pairing mode.
  3. Connect T 5th with phone 2.
  4. Tum on the Bluetooth feature of phone 1, select “Bluedio T 5th” in the Bluetooth list.

Line-in music playback:
Use the standard 3.5mm Type-C audio cable to connect the headphones with your mobile phone and computer.
Note: Turn off the headphones when using this feature.

Line-out music playback:
Connect headphones 1 with your mobile phone via Bluetooth first, then turn off the ANC function and use the 3.5mm Type-C audio cable to connect headphones 1 with headphones 2.
Note: Turn off the ANC function before using this feature. The headphones 2 must support 3.5mm audio jack.

Charge the headphones:
Turn off the headphones before charging.Use the included Type-C charging cable to connect the headphones with a computer or wall charger. While charging, the red light stays on. Allow 1.5-2 hours for a full charge. Once fully charged, the blue light will stay on.

Specifications
Bluetooth version: 4.2
Bluetooth operating range: up to 33 feet (free space)
Bluetooth transmission frequency: 2.4 GHz-2.48GHz
Bluetooth profiles: A2DP, AVRCP, HSP, HFP
Drivers: 57mm
Noise-reduction: -25dB
Impedance: 160
Frequency response: 15H.-25KHz
Sound Pressure Level (SPL): 115dB
Standby time about: 1000 hours
Bluetooth music/talk time: about 25 hours
Pure ANC time: about 28 hours
Charging time: 1.5-2 hours for full charge
Operating temperature range: -101C to 5010 only
Charging voltage/current: 5W>500mA
Output power: 50mW v 50mW

Purchase verification
You can find the verification code by scraping the coating off the secudty label that is affixed to the original packaging. Enter the code on our official website: www.bluedio.com for purchase verification.

Learn more and get support
Welcome to visit our official website: www.bluedio.com: Or to email us at aftersales@bluedio.com Or to call at at 400-889-0123.

Questions about your Manual ? Post in the comments!

Leave a comment

Your email address will not be published. Required fields are marked *