AXXESS BACKUPCAM-3 Camera Adapter
Product Information
The BACKUPCAM-3 is a product designed for GM Vehicles 2014-up. It allows the retention of the factory backup camera to be viewed through the display screen on an aftermarket radio or a stand-alone monitor. For more detailed information about the product and up-to-date vehicle specific applications, please visit AxxessInterfaces.com.
Product Usage Instructions
Compatible Vehicles
- CHEVROLET Colorado
- Cruze
- Cruze Hatchback
- Equinox
- Impala
- Malibu
- Silverado 1500-LD
- Silverado 1500
- Silverado 2500/3500
- Suburban
- Tahoe
GMC Vehicles
- Canyon
- Sierra 1500-Limited
- Sierra 1500
- Sierra 2500/3500
- Yukon
- Yukon XL
Note: The vehicle must be running for the factory camera to power on.
Visit AxxessInterfaces.com for more detailed information about the product and up-to-date vehicle specific applications
INTRODUCTION
The BACKUPCAM-3 is designed to retain the factory backup camera to be viewed through the display screen on the aftermarket radio, or a stand-alone monitor.
COMPONENTS
- 12-pin harness with a yellow RCA jack
APPLICATIONS
CHEVROLET
- Colorado (†): 2015-up
- Cruze (†): 2016-2018
- Cruze Hatchback (†): 2016-2018
- Equinox (†): 2018
- Impala: 2014-up
- Malibu (†): 2016-2018
- Silverado: 1500-LD (†) 2019
- Silverado: 1500 (†) 2014-2018
- Silverado: 2500/3500 (†) 2015-up
- Suburban: 2015-up
- Tahoe: 2015-up
GMC
- Canyon (†): 2015-2017
- Sierra 1500-Limited (†): 2019
- Sierra 1500 (†): 2014-2018
- Sierra 2500/3500 (†): 2015-up
- Yukon: 2015-up
- Yukon XL: 2015-up
(†) With RPO code I05 or I06 radio
Note: The vehicle must be running for the factory camera to power on.
Connections to be made
From the 12-pin harness with a Yellow RCA jack
To the aftermarket radio:
- Connect the Yellow RCA jack to the BACKUP CAMERA input.
To the vehicle:
- Connect the female 12-pin harness with a Yellow RCA jack, to the male Gray harness removed from the Human Machine Interface module. (Figura A)
For the Chevy Colorado and GMC Canyon:
- This module is located in the radio cavity, down low.
For all other models:
- This module is located behind the glove box. There are (2) modules behind the glove box. This module is behind the metal dashboard support. (Figura B)
- Drop the glove box down by first removing the retaining cable on the right side. Then squeeze the glove box sides and gently pull down.
- Remove (6) T-15 Torx screws securing the plastic panel now exposed.
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow.
Metra recommends MECP certified technicians
If you are having difficulties with the installation of this product, contact our Tech Support line either by phone at 1-800-253-TECH, or email at techsupport@metra-autosound.com. Before doing so, look over the instruction booklet a second time and ensure that the installation was performed exactly as the instruction booklet is stated. Have the vehicle apart and ready to perform troubleshooting steps before contacting Metra/Axxess Tech Support.
Contact
METRA. THE WORLD’S BEST KITS.®
© COPYRIGHT 2018 METRA ELECTRONICS CORPORATION
Documents / Resources
 |
AXXESS BACKUPCAM-3 Camera Adapter [pdf] Instruction Manual BACKUPCAM-3 Camera Adapter, BACKUPCAM-3, Camera Adapter, Adapter |