Introduction
This manual provides instructions for the assembly, operation, and maintenance of your DUMOS 26-inch counter height bar stools. Please read these instructions carefully before assembly and use to ensure safe and proper functionality. These bar stools are designed for use at kitchen islands, counters, and similar spaces, offering a comfortable seating solution with a modern aesthetic.
Image: Two DUMOS 26-inch counter height bar stools in a kitchen setting.
Safety Information
- Weight Capacity: Do not exceed the maximum weight capacity of 330 pounds (150 kg) per stool. Exceeding this limit may result in damage to the stool or personal injury.
- Stability: Always ensure the stool is stable and all connections are secure before sitting. Periodically check and tighten all bolts.
- Assembly: Follow all assembly instructions carefully. Incorrect assembly can lead to instability and potential hazards.
- Floor Protection: The stool legs are equipped with non-slip and anti-scratch protectors. Ensure these are intact to prevent floor damage and maintain stability.
- Children: Keep children away from the assembly area. Small parts may pose a choking hazard.
Package Contents
Before beginning assembly, verify that all parts listed below are present and undamaged. If any parts are missing or damaged, please contact customer support.
- Seat Cushion (A) - 2 pieces
- Metal Legs (B & C) - 2 sets (Left and Right for each stool)
- Supporting Round Tube (D) - 2 pieces
- Hardware Pack (Bolts E, G1, G2, and Wrench H) - 1 set
Image: Product details highlighting ergonomic design, durable structure, footrest, and non-slip protectors.
Setup and Assembly Instructions
Assembly is straightforward and typically takes 10-15 minutes per stool. All necessary hardware and tools are included.
- Prepare Components: Unpack all components and lay them out on a clean, soft surface to prevent scratches. Identify the Seat Cushion (A), Metal Legs (B & C), and Supporting Round Tube (D).
- Attach Supporting Tube: Align the round holes of the Supporting Round Tube (D) with the screw holes on the Metal Legs (B & C). Insert Bolts (E) and tighten them approximately 50% with the provided Wrench (H). Do not fully tighten yet.
- Attach Seat Cushion: Align the Metal Legs (B & C) over the pre-drilled holes underneath the Seat Cushion (A). Secure them with Bolts (G2) and the Wrench (H). Then, insert and tighten Bolts (G1) into the remaining screw holes.
- Final Tightening: Once all bolts are in place, gradually tighten all bolts (E, G1, G2) in the order shown in the assembly diagram until they are completely secure. Ensure the stool is stable and does not wobble.
For a visual guide, please refer to the official installation video:
Video: DUMOS Counter Height Bar Stools Installation Guide. This video demonstrates the step-by-step assembly process for the bar stools, showing how to connect the metal frame and attach the seat cushion.
Operating Instructions
These bar stools are designed for seating at counter-height surfaces. To ensure safe operation:
- Seating: Sit centrally on the seat cushion. Avoid standing on the stool or leaning excessively to one side, which could compromise stability.
- Weight Limit: Do not exceed the maximum weight capacity of 330 pounds (150 kg).
- Movement: When moving the stool, lift it rather than dragging it to prevent damage to your floor and the stool's non-slip protectors.
- Footrest: Utilize the integrated footrest for comfort and to reduce body pressure during extended sitting.
Video: DUMOS Counter Height Bar Stools Product Overview. This video showcases the design, features, and general use of the DUMOS counter height bar stools.
Maintenance
Proper care will extend the life and appearance of your bar stools.
- Cleaning: The faux leather upholstery is waterproof and resistant to spills. For routine cleaning, wipe the surface with a soft, damp cloth. For tougher stains, use a mild soap solution and immediately wipe dry. Avoid abrasive cleaners or harsh chemicals, as these can damage the material.
- Frame Care: Wipe the metal frame with a dry or slightly damp cloth. Avoid prolonged exposure to moisture.
- Hardware Check: Periodically inspect all bolts and connections to ensure they remain tight. Re-tighten if necessary to maintain stability and safety.
- Avoid Direct Sunlight: Prolonged exposure to direct sunlight can cause the faux leather to fade or crack over time.
Image: Detail of exquisite stitching and waterproof faux leather for easy cleaning.
Troubleshooting
If you encounter any issues with your bar stools, refer to the following common solutions:
- Stool Wobbles: This is usually caused by unevenly tightened bolts. Place the stool on a flat surface and systematically tighten all assembly bolts. Ensure they are all equally snug.
- Scratches on Floor: Check the non-slip protectors on the bottom of the legs. If they are missing or damaged, contact customer support for replacements. Ensure the floor is clean before moving stools.
- Loose Parts: If any parts feel loose, immediately stop using the stool and re-tighten all connections as per the assembly instructions.
Specifications
| Feature | Detail |
|---|---|
| Model Number | HJ3SE-6013-BK2 |
| Product Dimensions (D x W x H) | 20.87" x 18.51" x 36.23" (53cm x 47cm x 92cm) |
| Seat Height | 26 inches (66 cm) |
| Item Weight | 31.3 Pounds (14.2 kg) per stool (approx.) |
| Maximum Weight Recommendation | 330 Pounds (150 kg) |
| Color | Elegant Black |
| Frame Material | Metal (Powder-coated tubular) |
| Seat Material | Faux Leather (PU) |
| Assembly Required | Yes |
| Number of Pieces | 2 |
Image: Detailed dimensions and weight capacity of the bar stool.
Warranty and Support
For warranty information, please refer to the documentation included with your purchase or contact the retailer directly. If you have any questions, require replacement parts, or need further assistance, please reach out to DUMOS customer service through your purchase platform or the official DUMOS website.