WONLINK 3601-1 AX1500 WiFi Repeater Instruction Manual

1. Introduction

Thank you for choosing the WONLINK 3601-1 AX1500 WiFi Repeater. This device is designed to extend your existing wireless network coverage, eliminate Wi-Fi dead zones, and provide a stable, high-speed internet connection throughout your home or office. This manual will guide you through the setup, operation, and maintenance of your new WiFi repeater.

The WONLINK 3601-1 AX1500 WiFi Repeater extends your network with WiFi 6 technology, dual-band support, and easy WPS setup.

2. Product Overview

2.1. What's in the Box

• 1 x WONLINK AX1500 Repeater
• 1 x Network Cable
• 1 x Instruction Manual

2.2. Key Features

• Ultra-Fast WiFi 6: Experience next-generation wireless speeds for smoother streaming and gaming.
• Dual-Band AX1500: Combines 2.4 GHz (300 Mbps) and 5 GHz (1200 Mbps) bands for flexible and high-performance connections.
• One-Touch WPS Setup: Easily extend your Wi-Fi coverage by pressing the WPS button on both your router and the repeater.
• Advanced Dual-Core Chip: Ensures stable and reliable performance with features like overvoltage protection and security encryption.
• High-Gain Antennas: Equipped with 4 high-gain antennas for maximum signal reach and stability.
• Fast Ethernet Port: Connect wired devices like PCs, gaming consoles, or smart TVs for a stable connection.
• Efficient Heat Dissipation: Designed for optimal cooling to ensure long-term stability.
• WPA3 Security Protocols: Provides enhanced network security for your data.
• Wide Compatibility: Works with all Wi-Fi enabled devices, including routers, phones, tablets, laptops, Smart TVs, and smart home devices.

Advanced Dual-Core Chip for enhanced performance and security.

High-speed dual-band performance for various online activities.

Key design and security features for reliable operation.

Extensive compatibility and wide coverage for numerous devices.

3. Setup

There are two primary methods to set up your WONLINK 3601-1 WiFi Repeater: using the WPS button or via a web browser.

3.1. WPS (Wi-Fi Protected Setup) Method

1. Plug the repeater into a power outlet near your existing router.
2. Wait for the LED indicator on the repeater to slowly blink red.
3. Press the WPS button on your router, then immediately press the WPS button on the WONLINK repeater.
4. Wait for the LED indicator on the repeater to turn solid blue or yellow, indicating a successful connection.

3.2. Web UI Method

1. Plug the repeater into a power outlet in the same room as your existing router.
2. Wait until the LED indicator slowly blinks red.
3. Connect your wireless device (smartphone, laptop) to the repeater's default Wi-Fi network (e.g., "BrosTrend_EXT" or similar, check the product label).
4. Open a web browser and enter the default IP address or domain (e.g., http://brostrendwifi.com, check the product label) in the address bar.
5. Follow the on-screen instructions to create a login password and select your existing Wi-Fi network(s) to extend.
6. Enter the password for your existing Wi-Fi network(s).
7. Customize the extended network name and password if desired, then click "Extend".
8. Wait for the configuration to complete. The LED indicator will turn solid blue or yellow upon successful extension.

4. Operating Modes

The WONLINK 3601-1 supports multiple operating modes to suit various network needs:

• Repeater Mode (Range Extender): Extends the coverage of an existing wireless network. This is the most common mode for eliminating Wi-Fi dead zones.
• AP Mode (Access Point): Converts a wired network connection into a wireless access point. Ideal for adding Wi-Fi capability to a wired-only network.
• Router Mode: Functions as a primary router, creating a new wireless network from a modem connection.

The repeater offers flexible operating modes including Repeater, AP, and Router modes to adapt to different network setups.

5. Placement for Optimal Performance

Proper placement of your WONLINK 3601-1 WiFi Repeater is crucial for maximizing its effectiveness. Avoid placing the repeater too close or too far from your main router.

• Avoid placing too close: If the repeater is too close to the router, signal overlap may occur, leading to inefficient coverage.
• Avoid placing too far: If the repeater is too far from the router, it will receive a weak signal, resulting in poor extended Wi-Fi quality.
• Optimal Placement: Place the repeater roughly halfway between your router and the Wi-Fi dead zone. Ensure the LED indicator shows a solid blue or yellow light after configuration, indicating a good signal from the router.

Correct placement of the repeater ensures a strong, high-speed Wi-Fi signal in previously uncovered areas.

6. Maintenance

To ensure the longevity and optimal performance of your WONLINK 3601-1 WiFi Repeater, consider the following maintenance tips:

• Keep it Clean: Regularly wipe the device with a soft, dry cloth to prevent dust buildup, which can affect performance.
• Firmware Updates: Check the WONLINK official website periodically for firmware updates. Updating the firmware can improve performance, add new features, and enhance security.
• Proper Ventilation: Ensure the repeater is placed in a well-ventilated area and its vents are not obstructed to prevent overheating.
• Avoid Extreme Conditions: Do not expose the device to extreme temperatures, humidity, or direct sunlight.

7. Troubleshooting

If you encounter issues with your WONLINK 3601-1 WiFi Repeater, refer to the following common troubleshooting steps:

7.1. LED Indicator Status

• Solid Blue: The repeater is in the correct position and receiving a strong signal from the router.
• Solid Yellow: The repeater is receiving a good signal from the router.
• Solid Red: The repeater is receiving a weak signal from the router. Relocate the repeater closer to your router.
• Slowly Blinking Red: The repeater is not connected to your router. Relocate the repeater closer to your router or try reconfiguring.
• No LED: Check if the repeater is properly plugged into a working power outlet. If the issue persists, try resetting the device.

7.2. General Troubleshooting

• No Internet Access: Ensure your main router has internet access. Restart both your router and the repeater.
• Weak Signal in Extended Area: Adjust the repeater's position to be closer to your main router, ensuring the LED indicator is solid blue or yellow.
• Cannot Access Web UI: Ensure your device is connected to the repeater's Wi-Fi network. Try clearing your browser's cache or using a different browser. Verify the correct IP address or domain.
• Resetting the Repeater: If all else fails, you can perform a factory reset. With the repeater powered on, use a pin to press and hold the Reset button (usually located in a small hole) for about 5-10 seconds until the LEDs flash. The device will restart with factory default settings, and you will need to reconfigure it.

8. Specifications

9. Warranty and Support

For warranty information, please refer to the documentation provided with your purchase or contact your retailer. For technical support or assistance, please contact WONLINK customer service.

If you need help, send an email to support@brostrend.com. You will receive a response within 24 hours.