1. Introduction
This manual provides instructions for the BoxWave DirectSync PD 100W USB-C to USB-C Cable (10ft). This cable is designed for efficient power delivery and high-speed data transfer between compatible USB-C devices. It features a durable braided nylon construction and reinforced strain reliefs for enhanced longevity.
Image 1: The BoxWave DirectSync PD 100W USB-C to USB-C Cable (10ft) shown coiled next to a compatible smartphone, illustrating its design and intended use.
2. Setup and Connection
The DirectSync PD Cable is designed for simple plug-and-play functionality. No software installation is required.
- Identify Ports: Ensure both your charging adapter/power source and your device have USB-C ports.
- Connect for Charging: Insert one end of the USB-C cable into a compatible USB-C power adapter or power bank. Insert the other end into the USB-C charging port of your device (e.g., smartphone, tablet, laptop).
- Connect for Data Transfer: Insert one end of the USB-C cable into the USB-C port of your computer. Insert the other end into the USB-C port of your device. Your device should appear as a connected storage device on your computer.
Image 2: A close-up view of the coiled braided nylon cable, highlighting the robust USB-C connectors at each end.
3. Operating Instructions
3.1 Power Delivery (PD) Charging
The DirectSync PD Cable supports up to 100W Power Delivery, allowing for rapid charging of compatible devices, including laptops, tablets, and smartphones. For optimal charging speeds, ensure your power adapter also supports 100W PD or a wattage suitable for your device.
- Connect the cable as described in Section 2.
- The charging indicator on your device should activate, confirming power delivery.
Image 3: The DirectSync PD cable connected to a laptop, demonstrating its capability for high-wattage power delivery.
3.2 Data Transfer
This cable facilitates high-speed data transfers up to 480Mbps, allowing you to sync files, photos, and videos between your devices and computer efficiently.
- Connect the cable between your device and computer as described in Section 2.
- Once connected, your device should be recognized by your computer, allowing you to access and transfer files.
Image 4: The cable simultaneously charging a smartphone and connected to a laptop, demonstrating its dual function for charging and data synchronization.
4. Maintenance
Proper care will extend the life of your BoxWave DirectSync PD Cable.
- Storage: Store the cable in a clean, dry place. Avoid tightly coiling or bending the cable at sharp angles, especially near the connectors.
- Cleaning: Use a soft, dry cloth to clean the cable and connectors. Do not use harsh chemicals or abrasive materials.
- Handling: Always grasp the connector head when plugging or unplugging the cable, rather than pulling on the cable itself. This prevents stress on the internal wires and reinforced strain reliefs.
Image 5: A detailed view of the braided nylon exterior, highlighting the cable's durable construction designed to resist tangles and fraying.
Image 6: A close-up of the rubberized grommet strain relief at the connector, designed to prevent cable fraying and enhance durability.
5. Troubleshooting
- Device Not Charging:
- Ensure both ends of the cable are securely connected.
- Verify that your power adapter is functioning correctly and is compatible with your device's charging requirements.
- Check if your device's charging port is clean and free of debris.
- Confirm your power adapter supports Power Delivery (PD) for fast charging.
- Slow Charging:
- Ensure your power adapter provides sufficient wattage for your device. For 100W charging, a 100W PD adapter is required.
- Some devices may limit charging speed based on battery level or temperature.
- Data Transfer Issues:
- Ensure the cable is securely connected to both the device and the computer.
- Verify that your device is set to 'File Transfer' or 'MTP' mode when connected to a computer, if applicable.
- Try connecting to a different USB-C port on your computer.
6. Specifications
| Feature | Specification |
|---|---|
| Product Name | BoxWave DirectSync PD Cable |
| Model | DirectSync PD Cable |
| Connector Type | USB-C to USB-C |
| Power Delivery | Up to 100W |
| Data Transfer Speed | Up to 480Mbps |
| Cable Length | 10 feet (approximately 3 meters) |
| Material | Braided Nylon, Rubberized Grommet Strain Relief |
| Color | Jet Black |
| Item Weight | 6 ounces |
7. Warranty and Support
For warranty information or technical support regarding your BoxWave DirectSync PD Cable, please refer to the official BoxWave website or contact their customer service directly. Contact details are typically available on the product packaging or the manufacturer's website.
Website: www.boxwave.com
