Slevoo K1

Slevoo K1 Replacement Mineral Filter for C2-M25 User Manual

Model: K1

1. Product Overview

The Slevoo K1 Replacement Mineral Filter is designed to enhance your water by adding essential minerals and maintaining a balanced pH level. This filter is specifically compatible with C2-M25 water filtration systems, providing cleaner, healthier, and better-tasting water.

Woman pouring water from a pitcher with mineral icons (K, Si, Ca, Mg, Na) indicating mineral addition.

Image 1.1: The Slevoo K1 filter adds essential minerals like Potassium (K), Silicon (Si), Calcium (Ca), Magnesium (Mg), and Sodium (Na) to your filtered water.

Woman drinking water, with icons showing Calcium (Ca), Zinc (Zn), Potassium (K), Magnesium (Mg), and Sodium (Na) to illustrate increased mineral absorption.

Image 1.2: The filter is designed to increase the mineral content in your drinking water, supporting better mineral absorption.

A pH balance scale showing acidic to alkaline, with two glasses of water: one labeled 'Pure Water' and another 'Re-mineral Water' with mineral ions (Mg2+, K+, Ca2+, Sr2+, Fe).

Image 1.3: The Slevoo K1 filter helps maintain a balanced pH level in your water by introducing beneficial minerals.

2. Setup and Installation

Follow these steps to properly install your Slevoo K1 Replacement Mineral Filter into your compatible C2-M25 water filtration system.

  1. Prepare the System: Ensure your C2-M25 water filtration system is clean and empty.
  2. Remove Old Filter: Carefully remove the existing filter from the pitcher or system according to your C2-M25 system's instructions.
  3. Unpack New Filter: Remove the new Slevoo K1 mineral filter from its packaging.
  4. Rinse Filter: Rinse the new filter under cold tap water for approximately 15 seconds to remove any loose carbon particles.
  5. Insert Filter: Place the new Slevoo K1 filter into the designated slot in your C2-M25 system. Ensure it is seated firmly to prevent leaks.
  6. Initial Flush: Fill the system with water and discard the first two full pitchers of filtered water. This primes the filter and removes any remaining carbon dust.
A hand inserting a white replacement filter into the top of a water pitcher, with an inset showing a filter replacement indicator dial.

Image 2.1: The Slevoo K1 filter is designed for quick and easy replacement in compatible systems.

3. Operating Instructions

Once installed and flushed, the Slevoo K1 mineral filter operates automatically with your C2-M25 water filtration system.

  • Fill System: Fill your C2-M25 system with tap water.
  • Filter Process: The water will pass through the Slevoo K1 filter, where it will be filtered and remineralized.
  • Enjoy: Once the water has passed through the filter, it is ready for consumption.

4. Maintenance

Regular replacement of your Slevoo K1 mineral filter is crucial for optimal performance and water quality.

  • Filter Lifespan: For best results, replace the Slevoo K1 mineral filter every three months or after filtering approximately 40 gallons (150 liters) of water, whichever comes first.
  • Replacement Indicator: If your C2-M25 system has a filter replacement indicator, reset it after installing a new filter.
  • Storage: Store unused filters in a cool, dry place away from direct sunlight.
Two white Slevoo K1 mineral filters, indicating a pack of replacement filters.

Image 4.1: The Slevoo K1 filter is available in multi-packs for convenient replacement.

5. Troubleshooting

If you encounter any issues with your Slevoo K1 mineral filter, refer to the following common solutions:

  • Slow Filtration:
    • Ensure the filter is properly seated in the system.
    • The filter may be clogged. Replace the filter if it has reached its lifespan or if water flow is significantly reduced.
  • Unusual Taste/Odor:
    • Ensure the initial flush procedure (discarding the first two pitchers) was completed.
    • The filter may need replacement.
    • Check the water source for any unusual conditions.
  • Leaking:
    • Verify the filter is correctly and securely installed in the filter housing.
    • Inspect the filter and housing for any damage.

6. Specifications

AttributeDetail
Model NumberK1
MaterialPolypropylene (PP)
Product Dimensions2.2"D x 1.34"W x 2.2"H
Item Weight0.15 Pounds (approx. 2.4 ounces)
Product BenefitsRemoves impurities and provides mineral filtration for cleaner, healthier water. Durable and designed for pitcher-style filters.
Unit Count1.0 Count
Number of Items2 (This product includes two filters)

7. Warranty Information

Slevoo products are manufactured to high-quality standards. This product comes with a limited warranty against defects in materials and workmanship. For specific warranty terms and conditions, please refer to the packaging of your product or visit the official Slevoo website. Please retain your proof of purchase for warranty claims.

8. Customer Support

If you have any questions, concerns, or require assistance with your Slevoo K1 Replacement Mineral Filter, please contact Slevoo customer support through their official website or the contact information provided on your product packaging. Our team is dedicated to providing you with the best possible experience.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.