Antec C7 ARGB White Mid-Tower E-ATX PC Case

1. Product Overview

The Antec C7 ARGB White is a mid-tower E-ATX PC case designed for high-performance builds. It features seamless tempered glass front and side panels, vertical cooling support, and pre-installed ARGB PWM fans for optimal airflow and aesthetics.

Figure 1.1: Main view of the Antec C7 ARGB White PC Case, showcasing its full-view design with internal components and RGB lighting.

2. Setup and Installation

2.1 Panel Removal

The Antec C7 ARGB case features screw-free panels for easy access. The top panel, front panel, and both side panels are secured by studs and hooks, with clip handle positions at the rear for convenient removal. The lower front and lower left panels feature detachable mesh secured by hooks and magnets.

Figure 2.1: Illustration of the screw-free panels and their securing mechanisms (studs, hooks, magnets) for easy removal and installation.

2.2 Motherboard and Component Compatibility

• Motherboard Support: E-ATX (≤ 272mm), ATX, M-ATX, ITX.
• CPU Cooler Max Height: ≤ 180mm.
• GPU Max Length: ≤ 450mm.
• Power Supply Max Length: ≤ 210mm (including cables).

Figure 2.2: Internal view highlighting motherboard, CPU, GPU, and PSU placement, demonstrating the case's extensive interior space.

2.3 Power Supply Installation

The case features a rear pull PSU mount with EVA cushion pads for easier installation and safer operation. The power supply mounts vertically in the back.

Figure 2.3: Detailed view of the rear pull PSU mount, designed for convenient power supply installation.

2.4 Storage Installation

The right flip door supports up to 2 x 3.5" HDD/2.5" SSD. An additional tray in the case bottom can accommodate another 3.5" HDD/2.5" SSD. The case supports multiple hard drives, with different compatibility depending on the form factor of the installed motherboard, up to 3 x 3.5" HDD or 5 x 2.5" SSD at most.

Figure 2.4: View of the flip door storage mechanism, showing bays for 3.5-inch hard drives and 2.5-inch solid-state drives.

2.5 Cable Management

The case provides 32mm of cable management space and a removable flip-door cable cover, allowing for unobstructed cable management. Two Velcro straps are located on the back of the motherboard to avoid cable clutter, and two additional Velcro straps are at the rear for easier management of peripheral cables.

Figure 2.5: Illustration of the flip cable cover, demonstrating the 32mm space available for routing and organizing cables.

2.6 Cooling System Setup

The C7 ARGB supports extensive cooling configurations:

• Fan Support:
  • Top: 3 x 120mm fans or 2 x 140mm fans.
  • Rear: 1 x 120mm fan or 1 x 140mm fan.
  • Side: 3 x 120mm fans.
  • PSU Shroud: 3 x 120mm fans.
• Radiator Support:
  • Top: Up to 360mm.
  • Side: Up to 360mm.

The case comes with 3 x 120mm ARGB PWM reverse fans pre-installed on the right side and 1 x 140mm ARGB PWM fan at the rear. An included ARGB & PWM controller allows lighting to be switched by an LED control button or synced with the motherboard.

Figure 2.6: Diagram illustrating the various fan and radiator mounting options available in the Antec C7 ARGB case.

Figure 2.7: Visual representation of the pre-installed 120mm and 140mm ARGB PWM fans, along with the integrated ARGB & PWM controller.

2.7 I/O Panel

The front I/O panel includes:

• Power Button
• LED Control Button
• Type-C 10Gbps x 1
• Headphone/Mic Combo Jack
• USB 3.0 x 2

Figure 2.8: Close-up of the front I/O panel, detailing the available ports and control buttons.

3. Operating Instructions

Once all components are correctly installed and connected, power on the system using the power button on the front I/O panel. Use the LED control button to cycle through various RGB lighting effects for the pre-installed fans, or synchronize lighting with your motherboard's software if connected via the ARGB header.

4. Maintenance

4.1 Dust Filter Cleaning

The case includes magnetic dust filters on the front and left panels, and a full-size pull-out filter on the bottom. Regularly remove and clean these filters to maintain optimal airflow and prevent dust buildup inside the case.

Figure 4.1: Visual guide to the location of the magnetic front and left dust filters, and the pull-out bottom filter.

4.2 General Cleaning

Use a soft, dry cloth to clean the exterior surfaces, including the tempered glass panels. For internal cleaning, use compressed air to remove dust from components and fan blades. Ensure the system is powered off and unplugged before performing any internal cleaning.

5. Troubleshooting

• No Power: Ensure all power cables (PSU to wall, PSU to motherboard, CPU, GPU) are securely connected. Verify the power switch on the PSU is in the 'on' position.
• Fans Not Spinning/RGB Not Working: Check fan connections to the motherboard or the included ARGB & PWM controller. Ensure the controller is receiving power and is correctly connected to the motherboard's ARGB header if synchronization is desired.
• Overheating: Verify all fans are spinning correctly and dust filters are clean. Ensure proper airflow configuration (intake/exhaust). Check CPU cooler and GPU cooler installation.
• Component Fit Issues: Refer to the compatibility specifications in Section 2.2. Ensure component dimensions do not exceed the case's maximum allowances.

For specific component-related issues, consult the respective component's instruction manual.

6. Specifications

7. Warranty and Support

Specific warranty information for the Antec C7 ARGB PC Case is not provided in this manual. Please refer to the official Antec website or contact Antec customer support for detailed warranty terms and conditions.

For further assistance or technical support, please visit the Antec Store or their official website.

8. Product Videos