Introduction
Thank you for choosing the HATHASPACE HSE200 True HEPA Air Purifier. This manual provides essential information for the safe and efficient operation, maintenance, and troubleshooting of your new air purifier. Please read it thoroughly before use and retain it for future reference.
The HATHASPACE HSE200 is designed to improve indoor air quality by effectively removing airborne particles and odors in spaces up to 200 square feet. It features a multi-stage filtration system, including an H13 True HEPA filter and an activated carbon filter, to capture 99.9% of dust, smoke, pet dander, odors, and VOCs.
Safety Information
- Always unplug the air purifier before moving it, cleaning it, or performing any maintenance.
- Do not operate the air purifier with a damaged cord or plug. If the cord or plug is damaged, contact customer support.
- Keep the air purifier away from water or other liquids. Do not use it in wet or damp environments.
- Ensure the air inlet and outlet are not blocked. Maintain at least 6 inches of clearance from walls and furniture.
- This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
- Use only HATHASPACE genuine replacement filters. Using unauthorized filters may void your warranty and affect performance.
Product Overview
The HATHASPACE HSE200 air purifier is designed for efficient air purification with a compact and sleek design.
Image: The HATHASPACE HSE200 True HEPA Air Purifier shown next to its product packaging, highlighting its compact, cylindrical white design with a perforated lower section for air intake and a control panel on top.
Key Components:
- Control Panel: Located on the top, includes Power Button and Fan Speed indicator.
- Air Inlet: Perforated section around the lower part of the unit for 360-degree air intake.
- Air Outlet: Top grille for purified air release.
- Filter Compartment: Located at the base, housing the multi-stage filter.
- Power Cord: Connects the unit to an electrical outlet.
Image: A close-up view of the top control panel of the HATHASPACE HSE200, clearly showing the Power Button and Fan Speed indicators (1, 2, 3).
Setup
Before first use, the power cord and filter must be properly installed.
- Unpack the Unit: Carefully remove the air purifier from its packaging.
- Access Filter Compartment: Twist open the base of the air purifier to access the filter compartment.
- Remove Power Adapter: Inside the filter compartment, remove the foam cover and take out the power adapter and cord.
- Install Filter: Ensure the filter is correctly seated in the compartment. Remove any plastic packaging from the filter before installation.
- Close Base: Securely twist the base back onto the unit.
- Position the Purifier: Place the air purifier on a flat, stable surface. Ensure there is at least 6 inches of clear space around all sides for optimal airflow.
- Connect Power: Plug the power adapter into the air purifier and then into a standard electrical outlet.
Image: A visual guide demonstrating how to twist open the base, remove the foam cover, take out the power adapter from inside the filter compartment, and properly install the filter.
Operation
Operating your HATHASPACE HSE200 air purifier is straightforward.
- Power On/Off: Press the Power Button () on the control panel to turn the unit on or off.
- Adjust Fan Speed: After powering on, the unit will start at a default fan speed. Press the Fan Speed Button () repeatedly to cycle through the available fan speeds (1, 2, 3). The corresponding indicator light will illuminate.
- Speed 1: Lowest setting, ideal for quiet operation in bedrooms.
- Speed 2: Medium setting, suitable for general use.
- Speed 3: Highest setting, for rapid air purification.
- Auto Mode (if applicable): This model features a smart sensor. When in Auto Mode, the purifier automatically adjusts fan speed based on detected air quality. Refer to the product's specific features for activation if available.
Image: The HATHASPACE HSE200 air purifier with a list of its smart features, including low noise, 3-level fan speed, H13 True HEPA grade, coverage up to 200 sq. ft., lightweight & compact design, 3 stages of purification, and suitability for bedrooms.
Maintenance
Regular maintenance ensures optimal performance and extends the lifespan of your air purifier.
Filter Replacement:
The multi-stage filter should be replaced every 3-4 months, depending on usage and air quality. A dirty filter will reduce purification efficiency.
- Power Off and Unplug: Always turn off and unplug the air purifier before replacing the filter.
- Access Filter: Twist open the base of the unit to access the filter compartment.
- Remove Old Filter: Carefully pull out the used filter. Dispose of it properly.
- Install New Filter: Unwrap the new HATHASPACE replacement filter and insert it into the compartment, ensuring it is seated correctly.
- Close Base: Twist the base back onto the unit until it is securely closed.
- Reset Filter Indicator (if applicable): Some models have a filter reset button or procedure. Refer to your specific model's instructions if a filter change indicator light is present.
Cleaning the Unit:
- Exterior: Wipe the exterior of the air purifier with a soft, dry cloth. Do not use abrasive cleaners or solvents.
- Air Inlet/Outlet: Use a soft brush or vacuum cleaner with a brush attachment to gently clean dust from the air inlet and outlet grilles.
- Interior: Do not attempt to clean the interior components beyond filter replacement.
Troubleshooting
If you encounter issues with your HATHASPACE HSE200, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Unit does not turn on. |
|
|
| Reduced airflow or purification efficiency. |
|
|
| Unusual noise. |
|
|
If the problem persists after trying these solutions, please contact HATHASPACE customer support.
Specifications
| Feature | Detail |
|---|---|
| Model Number | HSE200 |
| Dimensions (D x W x H) | 6.3"D x 6.3"W x 9.25"H |
| Weight | 1.98 Pounds |
| Coverage Area | Up to 200 Square Feet |
| Filter Type | H13 True HEPA (captures 99.9% of particles as small as 0.3 microns) |
| Filtration Stages | 3-in-1 (Pre-filter, H13 True HEPA, Activated Carbon) |
| Fan Speeds | 3 Levels |
| Certifications | CARB Certified, ETL Certified |
| Color | White |
Warranty and Support
HATHASPACE products are designed for reliability and performance. For specific warranty details, please refer to the documentation included with your product or visit the official HATHASPACE website. Warranty terms may vary based on purchase location and registration.
For technical support, replacement parts, or any inquiries, please contact HATHASPACE customer service through their official website or the contact information provided in your product packaging.
Online Resources:
- HATHASPACE Official Store on Amazon
- User Manual (PDF) - for additional reference
