Important Safety Information
Please read and understand all instructions before beginning installation. Failure to follow these instructions may result in electric shock, fire, or other hazards that could cause injury or property damage.
- Always disconnect power at the main circuit breaker before installation or maintenance.
- Consult a qualified electrician if you are unsure about the installation process.
- Ensure all electrical connections are made in accordance with local codes and ordinances.
- This fixture is rated for damp locations. Do not install in areas with direct water exposure.
- Use only the specified bulb type and wattage to avoid overheating.
- Handle glass components with care to prevent breakage.
Package Contents
Verify that all components listed below are present before beginning installation.
- 1 x EGLO Tarbes 3-Light Bath Vanity Fixture (Model 205621A)
- 1 x Mounting Hardware Kit (screws, wire nuts, mounting plate)
- 1 x Instruction Manual
Image: The EGLO Tarbes 3-Light Bath Vanity Fixture, showcasing its matte black finish and geometric open-frame shades.
Tools Required (Not Included)
- Phillips Head Screwdriver
- Flat Head Screwdriver
- Wire Strippers
- Pliers
- Electrical Tape
- Safety Glasses
Setup and Installation
Follow these steps carefully for proper installation.
- Turn Off Power: Locate the circuit breaker controlling the power to the installation location and turn it off. Verify power is off using a voltage tester.
- Prepare Mounting Plate: Attach the mounting plate to the junction box using the provided screws. Ensure it is securely fastened.
- Make Electrical Connections:
- Connect the fixture's white wire to the supply's white (neutral) wire using a wire nut.
- Connect the fixture's black wire to the supply's black (hot) wire using a wire nut.
- Connect the fixture's ground wire (bare copper or green) to the supply's ground wire and the mounting plate's ground screw.
- Ensure all connections are tight and secure. Wrap wire nuts with electrical tape for added security.
- Mount the Fixture: Carefully align the fixture with the mounting plate and secure it using the provided screws. Ensure the fixture is flush against the wall.
- Install Bulbs: Insert three (3) E26 base bulbs (not included) into the sockets. The fixture supports incandescent or LED bulbs up to 40 watts each.
- Restore Power: Turn the power back on at the circuit breaker. Test the fixture to ensure it functions correctly.
Operating Instructions
The EGLO Tarbes 3-Light Bath Vanity is operated via a standard wall switch connected to your home's electrical system. If connected to a compatible dimmer switch, the light output can be adjusted.
- On/Off: Flip the wall switch to turn the light fixture on or off.
- Dimming (Optional): If a compatible dimmer switch is installed, adjust the dimmer control to increase or decrease the light intensity. Ensure you use dimmable bulbs if utilizing this feature.
Maintenance
Regular maintenance ensures the longevity and optimal performance of your light fixture.
- Cleaning: Turn off power before cleaning. Wipe the fixture with a soft, dry cloth. Do not use abrasive cleaners or solvents, as they may damage the finish.
- Bulb Replacement: Turn off power before replacing bulbs. Allow bulbs to cool completely. Unscrew old bulbs and screw in new E26 base bulbs, up to 40 watts each.
- Inspection: Periodically check all connections and mounting hardware for tightness.
Troubleshooting
Refer to the table below for common issues and their solutions.
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on. | No power to the fixture. Bulb is faulty or loose. Incorrect wiring. | Check circuit breaker. Replace or tighten bulb. Verify wiring connections. |
| Light flickers. | Loose bulb. Incompatible dimmer switch/bulb. Loose wiring connection. | Tighten bulb. Ensure dimmer and bulbs are compatible. Check wiring connections. |
| Fixture hums. | Incompatible dimmer switch. | Replace with a high-quality, compatible LED dimmer switch if using LED bulbs. |
Specifications
Detailed technical specifications for the EGLO Tarbes 3-Light Bath Vanity.
| Feature | Detail |
|---|---|
| Model Number | 205621A |
| Brand | EGLO |
| Finish Color | Matte Black |
| Material | Metal |
| Dimensions (L x W x H) | 25 x 7.87 x 10.95 inches |
| Backplate Dimensions (L x W) | 25.25 x 4.5 inches |
| Number of Lights | 3 |
| Bulb Type | E26 Base (Incandescent or LED) |
| Max Wattage per Bulb | 40 Watts |
| Voltage | 120 Volts |
| Dimmable | Yes (with compatible dimmer and bulbs) |
| Moisture Rating | Damp Rated |
| Item Weight | 5 Pounds |
Image: Dimensional drawing of the EGLO Tarbes 3-Light Bath Vanity, showing overall length, height, and depth measurements.
Warranty Information
This EGLO product is covered by a 1-Year Limited Warranty from the date of purchase. This warranty covers defects in materials and workmanship under normal use.
The warranty does not cover:
- Damage caused by improper installation or maintenance.
- Damage caused by misuse, abuse, accidents, or neglect.
- Damage from unauthorized repairs or modifications.
- Normal wear and tear.
For warranty claims, please retain your proof of purchase.
Customer Support
If you have any questions, require assistance with installation, or need to report a missing or damaged part, please contact EGLO customer support. Refer to the EGLO website or product packaging for the most current contact information.
When contacting support, please have your product model number (205621A) and proof of purchase readily available.
