Instruction Manual

1. Introduction and Overview

This manual provides detailed instructions for the assembly, operation, and maintenance of your BANDAI Master Grade (MG) 1/100 Gundam Avalanche Exia model kit. The Gundam Avalanche Exia is a variant of the GN-001 Gundam Exia, featured in the side-story "Mobile Suit Gundam 00V: Battlefield Record." This highly detailed model kit allows for dynamic posing and recreation of memorable battle scenes.

Figure 1.1: Fully assembled Gundam Avalanche Exia model kit. This image illustrates the completed model with its distinctive Avalanche armor and weaponry.

2. Product Components

Before beginning assembly, ensure all components listed below are present in your kit. Refer to the included instruction manual for a detailed parts list and visual identification.

• Gundam Avalanche Exia plastic model runners
• GN Sword Kai
• GN Long Sword
• GN Short Blade
• GN Beam Saber (x2)
• GN Beam Sword (x2)
• Shield
• Display Base (green GN particle themed)
• Water slide decal sheet (x1)
• Instruction manual (x1)

3. Setup and Assembly

The assembly of the Gundam Avalanche Exia model kit requires careful attention to detail. Please follow the step-by-step instructions provided in the dedicated instruction manual included in your kit.

1. Preparation: Unpack all runners and identify parts according to the manual. Prepare necessary tools such as nippers, a hobby knife, and tweezers (not included).
2. Part Removal: Carefully cut parts from the runners using nippers. Trim any excess plastic (nubs) with a hobby knife for a clean finish.
3. Assembly Sequence: Follow the numerical and alphabetical sequence in the included instruction manual. Pay close attention to part orientation and connection points.
4. Decal Application: Apply water slide decals as indicated in the manual after major assembly steps are complete. Allow decals to dry completely before handling.
5. Final Checks: Ensure all joints move smoothly and parts are securely attached.

Note: This model kit is recommended for ages 15 and up due to small parts and intricate assembly.

4. Operating and Display

Once assembled, your Gundam Avalanche Exia can be posed in various dynamic configurations.

• Posing: The kit features highly articulated joints. Carefully manipulate limbs and body sections to achieve desired poses. Avoid excessive force to prevent breakage.
• High-Mobility Mode: The dash unit on the kit's legs can be deployed to reproduce the high-speed movement characteristic of the Avalanche Exia's high-mobility mode. Refer to the manual for specific deployment steps.
• Armament: Attach the various armaments (GN Sword Kai, GN Long Sword, GN Short Blade, GN Beam Sabers, GN Beam Swords, and Shield) to the designated hardpoints on the model.
• Display Base: Utilize the included green GN particle themed action base to display your model in aerial or dynamic ground poses, enhancing stability and visual appeal.

5. Maintenance

Proper care will ensure the longevity and appearance of your model kit.

• Cleaning: Dust the model regularly with a soft brush or compressed air. Avoid using harsh chemicals or abrasive materials.
• Storage: Store the model away from direct sunlight, extreme temperatures, and high humidity to prevent plastic degradation and discoloration.
• Handling: Handle the model by its main body parts rather than delicate appendages or weapons to prevent accidental detachment or damage.

6. Troubleshooting

Should you encounter any issues during assembly or display, consider the following common solutions:

• Parts Not Fitting: Double-check the instruction manual to ensure the correct parts are being used and their orientation is accurate. Sometimes, a small amount of excess plastic (flash) may need to be trimmed.
• Loose Joints: If a joint feels too loose, a thin layer of clear topcoat or a small piece of tape can be applied to the peg to increase friction.
• Missing Parts: Carefully re-check all runners and packaging. If a part is genuinely missing, contact the retailer or manufacturer's customer support with proof of purchase.
• Decal Issues: If water slide decals are not adhering, ensure the surface is clean and dry. Use a decal setting solution for better adhesion and to conform to curved surfaces.

7. Specifications

8. Warranty and Support

For any inquiries regarding missing parts, manufacturing defects, or assembly assistance not covered in this manual, please refer to the contact information provided on the product packaging or the official Bandai Hobby website. Keep your proof of purchase for any warranty claims.