NyPots Solar Automatic Drip Irrigation Kit User Manual

1. Product Overview

The NyPots Solar Automatic Drip Irrigation Kit (Model BSV-IC003) is designed to provide automated watering for up to 15 potted plants. This solar-powered system eliminates the need for external power sources, making it ideal for both indoor and outdoor use where direct sunlight is available. It features flexible tubing, T-joints for customizable distribution, and six preset timing modes to ensure your plants receive optimal hydration.

2. Package Contents

Verify that all components listed below are included in your package:

Figure 1: All components included in the NyPots Solar Automatic Drip Irrigation Kit.

• 1 x Solar Host (with integrated pump and control panel)
• 1 x Ground Stake
• 1 x Tubing (15 meters)
• 15 x Drippers
• 15 x T-joints
• 1 x Filter
• 1 x User Manual (this document)
• 2 x Screws (for wall mounting, if desired)
• 1 x Level Sensor (5 meters)

3. Setup Instructions

Follow these steps to set up your NyPots Solar Automatic Drip Irrigation Kit:

3.1. Solar Panel Placement

The solar panel must be placed in a location that receives direct sunlight for several hours each day to ensure proper charging of the internal battery and continuous operation. The system is suitable for both indoor and outdoor environments, provided adequate sunlight exposure.

Figure 2: Example placements for the solar panel to ensure direct sunlight exposure.

3.2. Water Source Connection

Place a bucket or container filled with water near your plants. The system's pump will draw water from this reservoir. Ensure the water level sensor is submerged in the water source.

Figure 3: Solar panel connected to a water source, illustrating the automatic charging feature.

The system features a 2200mAh battery that automatically charges via the solar panel, providing power for the pump.

3.3. Tubing and Dripper Installation

1. Connect the main tubing to the "OUT" port on the solar host.
2. Measure and cut the tubing to reach each of your 15 potted plants.
3. Insert T-joints into the main tubing at appropriate points to branch off to individual plants.
4. Attach a dripper to the end of each branch of tubing and insert it into the soil of each potted plant.
5. Ensure all connections are secure to prevent leaks.

Figure 4: Schematic of the drip irrigation system supporting 15 potted plants.

Video: Connecting the Outlet Pipe and T-Joints

4. Operating Instructions

The NyPots Solar Automatic Drip Irrigation Kit features six preset watering modes. Select the mode that best suits your plants' needs.

4.1. Selecting a Watering Mode

Use the "MODE" button on the solar host to cycle through the available watering frequencies and durations. The control panel will indicate the selected mode.

Figure 5: Control panel and table of 6 preset timer watering modes.

The system has an outlet watering flow rate of approximately 400 ml/min.

4.2. Power On/Off

Use the "ON/OFF" button to activate or deactivate the system. When active, the system will follow the selected watering schedule.

5. Maintenance

• Clean the Filter: Regularly check and clean the water filter to prevent blockages and ensure consistent water flow.
• Check Tubing and Drippers: Periodically inspect tubing for kinks, damage, or blockages. Ensure drippers are not clogged with soil or mineral deposits.
• Monitor Water Source: Ensure the water reservoir always contains sufficient water for the scheduled watering cycles.
• Solar Panel Cleaning: Keep the solar panel clean from dust and debris to maximize charging efficiency.
• Winterization (for outdoor use): In freezing conditions, drain the system and store components indoors to prevent damage from ice expansion.

6. Troubleshooting

• No Water Flow:
  • Check if the pump is turned on.
  • Ensure the water reservoir has enough water.
  • Inspect the filter for clogs and clean if necessary.
  • Check tubing for kinks or blockages.
  • Verify drippers are not clogged.
• System Not Charging:
  • Ensure the solar panel is in direct sunlight and not obstructed.
  • Clean the surface of the solar panel.
• Uneven Watering:
  • Check for leaks in tubing connections.
  • Ensure all drippers are properly installed and not clogged.
  • Verify the water source is elevated enough to provide adequate pressure, if applicable, or that the pump is functioning correctly.

7. Specifications

8. Warranty and Support

For warranty information and technical support, please refer to the contact details provided with your purchase documentation or visit the official NyPots website. Keep your purchase receipt as proof of purchase.