WYBOT Cordless Robotic Pool Cleaner (Model WY1102MAX) Instruction Manual

1. Introduction

Thank you for choosing the WYBOT Cordless Robotic Pool Cleaner, Model WY1102MAX. This manual provides essential information for the safe and effective operation, maintenance, and troubleshooting of your new pool cleaner. Please read this manual thoroughly before first use and retain it for future reference.

Safety Information

• Keep away from fire.
• Ensure the charging port is completely dry before connecting the charger.
• Do not operate the cleaner if the battery is damaged or leaking.
• Always remove the cleaner from the pool before adding chemicals or performing maintenance.

2. Package Contents

Verify that all items listed below are included in your package:

• Pool cleaner x 1
• Power adapter x 1
• Flipper & handle x 1
• Scraper x 2
• Retrieving hook x 1
• User manual x 1
• Quick Guide x 1

Image: Contents of the WYBOT Robotic Pool Cleaner package.

3. Setup

3.1 Initial Assembly

The WYBOT pool cleaner requires minimal assembly. Attach the flipper and handle to the main unit using the provided screws. Ensure they are securely fastened. The scrapers can be attached to the bottom of the unit. For pools with wrinkles, the two scrapers may need to be removed for optimal performance.

Image: Adjusting wheel settings and removing scrapers for different pool types.

3.2 Charging the Cleaner

Before first use, fully charge the pool cleaner. A full charge takes approximately 3.5-4 hours. The cleaner is equipped with a durable 5200mAH Li-battery.

1. Ensure the charging port on the cleaner is completely dry.
2. Connect the power adapter to the cleaner's charging port.
3. Plug the adapter into a power outlet.
4. The indicator light on the adapter will show the charging status.

Image: The robotic pool cleaner connected to its charger.

4. Operating Instructions

4.1 Placing the Cleaner in the Pool

1. Ensure the cleaner is fully charged.
2. Submerge the cleaner into the pool water. Allow air bubbles to escape until it rests on the pool floor.
3. Press the power button located on the bottom of the unit to activate it. You will hear a beep indicating it's powered on.

Video: Demonstration of placing the WYBOT pool cleaner into the pool and its initial operation.

4.2 Cleaning Cycle

The WYBOT cleaner operates for up to 100 minutes on a single charge, covering up to 861 sq.ft. It features dual-drive powerful motors and two bottom assist scrapers to effectively capture dirt, sand, small leaves, and debris. Special leakproof strips prevent debris from returning to the pool water.

Image: The robotic cleaner demonstrating powerful cleaning action on the pool floor.

4.3 Self-Parking Technology

The cleaner is equipped with smart sensor technology. When it encounters a wall, it automatically reverses direction. When the battery level is low (approximately 15%), the system automatically drives the robot closer to the shore for easy retrieval.

Image: The robotic cleaner intelligently navigating towards the pool edge.

4.4 Retrieving the Cleaner

Once the cleaning cycle is complete or the battery is low, the cleaner will park itself near the pool edge. Use the provided retrieving hook attached to a standard pool pole (not included) to lift the cleaner out of the water. Allow excess water to drain before handling.

Image: Easy retrieval of the lightweight pool cleaner using a hook.

5. Maintenance

5.1 Cleaning the Filter Tray

After each use, the filter tray should be cleaned to ensure optimal performance. The effortless pop-out feature allows for convenient cleaning.

1. Remove the cleaner from the pool.
2. Unlock the buckles on both sides of the cleaner to open the top cover.
3. Carefully remove the filter tray.
4. Rinse the filter tray thoroughly with a hose to remove all collected debris.
5. Reassemble the filter tray and top cover, ensuring the buckles are securely locked.

Image: Cleaning the filter tray with a hose after use.

5.2 Storage

Store the WYBOT pool cleaner in a dry environment when not in use. Ensure the unit is clean and dry before storage to prolong its lifespan.

6. Troubleshooting

6.1 Cleaner Gets Stuck

If the cleaner frequently gets stuck, especially in pools with uneven or wrinkled liners, consider removing the two bottom assist scrapers. Refer to the initial assembly section for guidance on scraper removal.

6.2 Reduced Cleaning Performance

If you notice reduced suction or cleaning effectiveness, check the filter tray. It may be full of debris and require cleaning. Ensure the filter is properly seated after cleaning.

6.3 Cleaner Does Not Start

Ensure the cleaner is fully charged. Verify that the power button on the bottom of the unit is pressed firmly. If the cleaner has just been removed from the pool, ensure the charging port is dry before attempting to charge again.

7. Specifications

8. Warranty & Support

WYBOT provides a 1-year warranty for this product. Additionally, a 30-day return period is offered. For any questions, technical support, or warranty claims, please contact WYBOT customer service through your retailer or the official WYBOT website.