1. Introduction
The GE LED+ Color Changing A19 LED Light Bulbs offer a versatile lighting solution with 16 vibrant colors and multiple lighting modes, controlled by an included remote. These bulbs are designed for easy installation without the need for an app, Wi-Fi, or a hub.
Key Features:
- Simple Setup: No app, hub, or Wi-Fi required.
- Color Changing: 16 RGB vivid colors plus 2 white temperatures (2700K soft white, 5000K daylight white).
- Dimmable: Brightness adjustable via remote.
- Multiple Light Modes: Choose from 5 settings: Gentle, Energetic, Wave, Smooth, and Standard.
- Energy Efficient: Long-lasting LED technology (up to 13.7 years average life).
- Remote Control: Controls up to 10 LED+ color bulbs within approximately 20 feet.
2. Setup Instructions
2.1. Bulb Installation
- Ensure the power to the light fixture is turned off at the switch before beginning installation.
- Carefully screw the GE LED+ Color Changing A19 LED Light Bulb into any standard E26 medium base fixture until it is snug. Do not overtighten.
- Turn on the power to the light fixture at the switch. The bulb should illuminate in its default setting.
2.2. Remote Control Pairing
The included remote control is pre-paired with the bulbs. No additional pairing steps are required. Simply ensure the remote has a working battery (CR2025) and point it towards the bulb(s) you wish to control.
3. Operating Instructions
The remote control allows for full customization of your GE LED+ bulbs. Ensure the remote is pointed towards the bulb(s) for optimal response.
3.1. Remote Control Functions:
- Power Button (⏻): Turns the bulb(s) on or off.
- Color Buttons (16 Colors): Select from a palette of 16 vibrant colors. Pressing a color button a second time may activate an alternate shade of that color.
- White Light Button (💡): Provides 2700K soft white light. Press a second time for 5000K daylight white.
- Brightness Adjustment (− / +): Use the minus (−) and plus (+) buttons to decrease or increase the light brightness in 25% increments.
- Light Mode Buttons:
- Strobe/Flash: The top mode button cycles through colors quickly (Strobe) or slowly (Flash) with a second press.
- Smooth/Fade: The bottom mode button transitions colors smoothly (Smooth) or fades between them (Fade) with a second press.
- Timer Button (⏲): Press this button up to 8 times to set an automatic shut-off delay, with each press adding one hour.
The remote can control up to 10 GE LED+ color bulbs simultaneously, provided they are within approximately 20 feet and have a clear line of sight.
4. Maintenance
4.1. Cleaning the Bulb
To clean your LED+ bulb, ensure the power is off and the bulb is cool to the touch. Wipe the bulb with a soft, dry cloth. Do not use liquid cleaners or abrasive materials, as these can damage the bulb's surface or internal components.
4.2. Remote Control Battery Replacement
The remote control uses a CR2025 coin cell battery. If the remote's range or responsiveness decreases, the battery may need replacement. To replace the battery:
- Locate the battery compartment on the back of the remote.
- Slide open the battery tray.
- Remove the old CR2025 battery and insert a new one, ensuring the correct polarity (+ side up).
- Close the battery tray securely.
Note: Some users have reported improved remote performance when replacing the CR2025 battery with a CR2032 battery, which is slightly thicker and may ensure better contact within the battery compartment.
5. Troubleshooting
If you encounter issues with your GE LED+ Color Changing A19 LED Light Bulbs, refer to the following common troubleshooting steps:
- Bulb Not Lighting Up:
- Ensure the bulb is securely screwed into the fixture.
- Verify that the light fixture is receiving power and the wall switch is in the 'on' position.
- Test the bulb in a different, known-working fixture to rule out a fixture issue.
- Remote Control Not Working:
- Check the remote's battery. Replace the CR2025 battery if it is dead or low on power. Ensure it is inserted with the correct polarity.
- Ensure there are no physical obstructions between the remote and the bulb(s). The remote uses infrared technology, which requires a clear line of sight.
- Point the remote directly at the bulb(s) you wish to control. The effective range is approximately 20 feet.
- Confirm the remote is oriented correctly; the color buttons should be at the bottom when pointing.
- Remote Interferes with Other Devices:
- If the remote's signal affects other infrared-controlled devices (e.g., televisions), try operating the remote from a different angle or closer to the bulb(s) to minimize signal spread.
- Temporarily block the remote's signal to other devices if necessary.
6. Specifications
| Specification | Detail |
|---|---|
| Brand | GE |
| Model Number | 10043168502174 |
| Light Type | LED |
| Special Features | Color Changing, Dimmable, Energy Efficient, Long Lasting |
| Wattage | 9.5 watts |
| Bulb Shape Size | A19 |
| Bulb Base | E26 Medium |
| Incandescent Equivalent Wattage | 60 Watts |
| Light Color | Multicolor (16 colors + 2 white temperatures) |
| Voltage | 120 Volts (Accepted: 100 to 120 Volts and 60 Hertz) |
| Color Temperature | 2700 Kelvin (Soft White) |
| Brightness | 800 Lumens (White Brightness: 760 Lumens) |
| Average Life | 13 Years |
| Control Method | Remote |
| Indoor/Outdoor Usage | Indoor |
| Material | Plastic |
| Product Dimensions | 2.6"W x 2.6"H |
| Item Weight | 6.1 ounces (0.38 Pounds) |
7. Warranty and Support
7.1. Warranty Information
This GE LED+ product is covered by a manufacturer's warranty. For detailed information regarding the warranty period and terms, please refer to the product packaging or visit the official GE Lighting website. The average life of these bulbs is estimated at 13 years.
7.2. Customer Support
For further assistance, technical support, or to inquire about replacement parts, please contact GE customer service. Contact information can typically be found on the product packaging, the quick start guide included with your purchase, or on the official GE Lighting website.