1. Introduction
This manual provides essential instructions for the safe and efficient operation, installation, and maintenance of your Alpine Corporation 31-inch Outdoor Tranquil Zen Pagoda Fountain with LED Lights. Please read this manual thoroughly before assembly and use, and retain it for future reference.
Image 1.1: The Alpine Corporation 31-inch Outdoor Tranquil Zen Pagoda Fountain.
2. Important Safety Information
To reduce the risk of electric shock, fire, or injury, observe the following safety precautions:
- Ensure the fountain is placed on a stable, level surface to prevent tipping.
- Connect the fountain only to a properly grounded outlet.
- Do not operate the fountain if the power cord or pump is damaged.
- Always disconnect the power supply before performing any maintenance or cleaning.
- Keep children and pets away from the fountain during operation to prevent accidents.
- Do not allow the pump to run dry; ensure the water level is always sufficient to cover the pump.
- Protect the power cord from sharp objects, hot surfaces, and heavy traffic areas.
- This fountain is designed for outdoor use.
3. Package Contents
Verify that all components are present and undamaged before assembly. If any parts are missing or damaged, contact customer support.
- Fountain unit (Pagoda top, main body, water basin)
- Water pump with attached LED lights
- Power adapter
- Instruction Manual
4. Setup Instructions
4.1 Unpacking and Inspection
- Carefully remove all components from the packaging.
- Inspect the fountain for any signs of damage during transit.
- Place all parts on a soft, clean surface to prevent scratches.
4.2 Placement
- Choose a level, stable location for your fountain.
- Ensure the chosen location is within reach of a grounded electrical outlet.
- Consider proximity to plants or structures that might be affected by splashing water.
Image 4.1: Example of suitable fountain placement on a level outdoor surface.
4.3 Assembly
- Place the main body of the fountain on the chosen level surface.
- Locate the pump and its attached tubing.
- Connect the pump's tubing to the water inlet located inside the fountain's pagoda structure. Ensure a secure fit.
- Place the pump inside the water basin at the bottom of the fountain, ensuring it is fully submerged once water is added.
- Carefully route the pump's power cord out of the fountain, ensuring it does not interfere with water flow or stability.
4.4 Filling with Water
- Fill the fountain's water basin with distilled water or tap water.
- Ensure the water level is sufficient to completely submerge the pump. Do not overfill.
5. Operating Instructions
5.1 Initial Operation
- Once the fountain is assembled and filled with water, plug the power adapter into a grounded electrical outlet.
- The pump will begin circulating water, and the LED lights will illuminate.
- Allow a few moments for water to fully circulate and for air to be expelled from the pump and tubing.
Image 5.1: The fountain in operation, showcasing the illuminated LED lights.
5.2 Water Level Maintenance
- Check the water level daily, especially in warm or windy conditions, as water evaporates.
- Refill the basin as needed to ensure the pump remains fully submerged. Running the pump dry will cause damage and void the warranty.
Image 5.2: Detail of water flowing from the pagoda into the basin.
6. Maintenance
6.1 Cleaning the Fountain
- Weekly: Add a non-toxic algaecide to the water to prevent algae buildup.
- Monthly: Drain the fountain and clean all surfaces with a soft brush and mild soap. Rinse thoroughly to remove any soap residue.
- Avoid using harsh chemicals or abrasive materials, as these can damage the fountain's finish.
6.2 Cleaning the Pump
- Disconnect the power supply before cleaning the pump.
- Remove the pump from the fountain.
- Disassemble the pump cover and impeller.
- Clean all parts with a small brush and clean water to remove any debris or mineral deposits.
- Reassemble the pump and place it back into the fountain.
6.3 Winterization
- Before the first frost, drain all water from the fountain.
- Clean the fountain and pump thoroughly.
- Store the fountain and pump in a dry, frost-free location during winter months to prevent damage from freezing water.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Fountain not operating / Pump not running |
|
|
| Water flow is weak or inconsistent |
|
|
| LED lights not working |
|
|
| Fountain is leaking |
|
|
| Pump is noisy |
|
|
8. Specifications
| Feature | Detail |
|---|---|
| Model Number | DIG370 |
| Dimensions (L x W x H) | 17" x 13" x 31" (43.2 cm x 33 cm x 78.7 cm) |
| Weight | 10.04 kg (22.13 lbs) |
| Material | Cement, Sand, Fiberglass (Durable, weather-resistant, rust-resistant) |
| Power Source | Corded Electric |
| Special Features | Integrated LED Lights, Interior Pump |
Image 8.1: Fountain dimensions diagram.
9. Warranty Information
This Alpine Corporation fountain is covered by a one-year manufacturer's warranty from the date of purchase. This warranty covers defects in materials and workmanship under normal use. It does not cover damage caused by improper installation, misuse, neglect, freezing temperatures, or unauthorized repairs.
Please retain your proof of purchase for warranty claims.
10. Customer Support
If you have any questions, require assistance with setup, or need to report a defect, please contact Alpine Corporation customer support. Refer to the contact information provided with your product packaging or visit the official Alpine Corporation website for support details.
For more information, visit the Alpine Corporation Store on Amazon.
