1. Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your HALO LT4069FS351EWHR 4-inch Recessed LED Retrofit Downlight. This all-in-one LED trim is designed to replace existing can lighting fixtures, offering selectable color temperature options and dimming capabilities. It is suitable for both indoor and outdoor applications, including wet locations like showers.
2. Important Safety Information
- WARNING: Risk of electric shock. Disconnect power at the fuse or circuit breaker before installation or servicing.
- WARNING: Risk of fire. Use only in circuits specified in the product specifications.
- Installation must be performed by a qualified electrician in accordance with national and local electrical codes.
- Do not modify or alter the fixture.
- Ensure the fixture is securely installed to prevent falling.
- This device is not intended for use with emergency exits.
3. Package Contents
Verify that all components are present before beginning installation:
- HALO 4-inch Recessed LED Retrofit Downlight (LT4069FS351EWHR)
- Edison Base Adapter (for screw-in installation)
- Instruction Manual
Figure 1: HALO 4-inch Recessed LED Retrofit Downlight with Edison base adapter and quick connectors.
4. Specifications
| Feature | Specification |
|---|---|
| Brand | HALO |
| Model Number | LT4069FS351EWHR |
| Size | 4 Inch |
| Color Temperature (CCT) | 3000K (Warm White), 4000K (Bright White), 5000K (Daylight) - Selectable |
| Brightness | 665 Lumens |
| Wattage | 7.57 watts |
| Voltage | 120 Volts |
| Dimmable | Yes (to 10% with compatible 120V dimming switch) |
| Indoor/Outdoor Usage | Outdoor (Water Resistant) |
| Installation Type | Retrofit |
| Material | Plastic |
| Product Dimensions | 3.87"L x 3.87"W x 1.87"H |
| Item Weight | 8.4 ounces |
Figure 2: Product dimensions showing height of 3.15 inches and width of 5.31 inches.
Figure 3: Technical drawing illustrating the side and top view with precise measurements in inches and millimeters.
5. Setup and Installation
Follow these steps to install your HALO Recessed LED Retrofit Downlight:
- Turn Off Power: Before starting, ensure the power to the existing fixture is turned off at the circuit breaker.
- Remove Existing Fixture: Carefully remove your old recessed lighting trim and bulb from the housing.
- Connect Adapter: If your existing housing uses an Edison screw-in socket, screw the provided Edison base adapter into the socket.
- Select Color Temperature: Locate the CCT (Color Correlated Temperature) switch on the back of the LED fixture. Choose your desired color temperature (3000K, 4000K, or 5000K) by sliding the switch. It is recommended to set this before final installation.
- Connect Wiring: Connect the quick connectors from the LED fixture to the corresponding connectors from the Edison base adapter or directly to the housing wiring if applicable. Ensure a secure connection.
- Insert Fixture: Gently push the LED retrofit downlight into the existing recessed housing. The spring clips on the sides of the fixture will secure it in place.
- Restore Power: Turn the power back on at the circuit breaker.
Figure 4: Visual guide showing the four main steps of installation: screwing in the adapter, connecting wires, inserting the fixture, and securing the trim.
Figure 5: Close-up of the CCT switch on the back of the fixture, allowing selection between 3000K, 4000K, and 5000K.
6. Operating Instructions
Once installed, your HALO LED downlight is ready for use:
- Turning On/Off: Operate the light using your standard wall switch.
- Dimming: If connected to a compatible 120V dimming switch (not included), you can adjust the light output from 100% down to 10%.
- Color Temperature: The chosen color temperature (3000K, 4000K, or 5000K) will remain set until manually changed via the switch on the fixture.
7. Maintenance
The HALO LED Retrofit Downlight requires minimal maintenance:
- Cleaning: Ensure power is off before cleaning. Wipe the fixture with a soft, damp cloth. Do not use abrasive cleaners or solvents.
- LED Longevity: The integrated LED is designed for long life and does not require bulb replacement.
8. Troubleshooting
If you encounter issues with your downlight, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on | No power to the fixture; Loose wiring connection; Faulty switch | Check circuit breaker; Verify all wire connections are secure; Test the wall switch. |
| Light flickers or blinks | Incompatible dimmer switch; Loose wiring; Overheating | Ensure dimmer is LED compatible; Check wiring connections; Ensure proper airflow around the fixture. |
| Incorrect color temperature | CCT switch set incorrectly | Turn off power, remove fixture, and adjust the CCT switch on the back. |
9. Warranty Information
This HALO product is backed by a 5-year limited warranty. For detailed warranty terms and conditions, please refer to the documentation included with your purchase or visit the official HALO website.
10. Customer Support
For technical assistance, troubleshooting, or warranty claims, please contact HALO customer service. Contact information can typically be found on the product packaging or the official HALO website.
