1. Product Overview
The DieseRC Radio Frequency Light Remote Control Switch system allows for wireless control of lights and other electrical appliances. It consists of a relay receiver and two remote control transmitters, operating on a 433MHz RF frequency. This manual provides instructions for installation, setup, and operation.
2. Package Contents
- 1x Relay Receiver
- 2x Transmitters (with CR2016 batteries included)
- 1x Product Manual (this document)
3. Product Specifications
| Parameter | Value |
|---|---|
| Receiver Working Voltage | AC 85V~240V |
| Quiescent Current | <5mA |
| Max Current | 10A |
| RF Frequency | 433MHz |
| Working Temperature | -30°C ~ +80°C |
| Receiving Sensitivity | >97dbm |
| Storage Remote Controls | Up to 20 pieces |
| Support Encoding | 1527 Learning code |
| RF Operating Mode | ASK superheterodyne wireless reception |
| Receiving Range (Open Space) | >50 meters |
| Pin Configuration | N/L |
| Operating Modes | Momentary / Toggle / Latched Mode |
| Transmitter Battery | 2x CR2016 (included) |
| Wattage | 1500 watts |
| Maximum Switching Current | 10 Amps |
4. Installation
The receiver unit is designed for easy integration into existing electrical systems. It should be installed between the power supply and the device you wish to control (e.g., a lamp). The compact size (70*38*21 mm) allows for flexible placement. Ensure all power is disconnected before installation.
The receiver is housed in a protective box for enhanced safety. No complex wiring is required for basic operation, but professional installation is recommended for those unfamiliar with electrical work.
5. Operating Modes
The receiver supports three distinct operating modes: Momentary, Toggle, and Latched. The desired mode must be set during the setup process.
5.1. Momentary Mode
In Momentary Mode, the relay activates only while the remote button is pressed. Releasing the button deactivates the relay.
- Press and hold one button on the transmitter: The connected device will turn ON.
- Release the button: The connected device will turn OFF.
5.2. Toggle Mode
In Toggle Mode, each press of the remote button alternates the relay's state (ON/OFF).
- Press a button on the transmitter: The connected device will turn ON.
- Press the same button again: The connected device will turn OFF.
Note: The product is typically pre-set to Toggle Mode from the factory.
5.3. Latched Mode
Latched Mode requires two distinct buttons on the remote: one for ON and one for OFF.
- Press the "ON" button: The connected device will turn ON.
- Press the "OFF" button: The connected device will turn OFF.
Note: This mode requires a remote with at least two distinct buttons for ON/OFF functionality.
6. Setup and Pairing
To pair a transmitter with the receiver and set the operating mode, follow these steps:
6.1. Pairing for Momentary Mode
- Press the learning button on the receiver 1 time.
- Wait for approximately 3 seconds.
- Press any button on the transmitter. The pairing is successful.
6.2. Pairing for Toggle Mode
- Press the learning button on the receiver 2 times.
- Wait for approximately 3 seconds.
- Press any button on the transmitter. The pairing is successful.
6.3. Pairing for Latched Mode
- Press the learning button on the receiver 3 times.
- Wait for approximately 3 seconds.
- Press the desired "ON" button on the transmitter.
- Press the desired "OFF" button on the transmitter. The pairing is successful.
Note: For Latched Mode, you need a transmitter with at least two distinct buttons to assign ON and OFF functions.
7. Resetting the Receiver
To clear all paired transmitters from the receiver's memory:
- Press the learning button on the receiver 8 times consecutively.
- The reset is successful.
Important: After a reset, all previously paired remote controls will no longer function with this receiver. You will need to re-pair them following the setup instructions above.
8. Product Features and Applications
The DieseRC RF Wireless Relay Module offers robust performance and versatility:
- Strong Signal: The 433MHz radio frequency signal can penetrate walls, floors, and doors, providing reliable control within a 50-meter range in open areas.
- High Capacity Relay: Equipped with a 10 Amp relay, it can handle high-power electrical appliances up to 1500W.
- Durable Components: The high-quality relay is rated for over 400,000 operations, and the remote control transmitter buttons are designed for over 500,000 clicks.
- Wide Voltage Compatibility: The receiver supports AC 85V~250V, making it suitable for 110V, 220V, 230V, and 240V systems.
- Compact Design: The mini size of the receiver (70*38*21 mm) and the portable key-fob style transmitters ensure convenience and discreet installation.
This system is suitable for a wide range of applications in homes, farms, factories, offices, laboratories, and supermarkets. It can remotely control various devices such as lamps, lighting fixtures, ventilation equipment, food waste disposers, and other DIY wireless projects.
9. Transmitter Details
The remote control transmitter features a simple design for ease of use.
The transmitter includes an indicator light, a silicone button for operation, and a metal keychain for portability. It is powered by two CR2016 batteries, which are replaceable.
