Hugolog Keyless Entry Door Lock Instruction Manual

Product Overview

The Hugolog Keyless Entry Door Lock provides convenient and secure access to your home or office. This manual outlines the installation, operation, maintenance, and troubleshooting for your device.

Image: Front and back view of the Hugolog Keyless Entry Door Lock, showcasing the keypad on one side and the interior assembly on the other.

Package Contents

Before beginning installation, please verify that all components are present in the package:

Image: All components included in the Hugolog Keyless Entry Door Lock package, laid out on a white surface. This includes the exterior keypad assembly, interior assembly, latch, strike plate, mounting plate, screws, backup keys, and installation guide.

• Exterior Keypad Assembly
• Interior Assembly
• Latch
• Mounting Plate
• Handle
• Lock Cylinder
• Backup Key(s)
• Reset Tool
• Strike Plate
• Various Screws (Latch Screws, Mounting Screws, Interior Assembly Screws)
• Installation Guide / Programming Instruction
• Drilling Drawing (if needed for new installations)

Setup and Installation

Follow these steps carefully to install your Hugolog Keyless Entry Door Lock. For visual guidance, please refer to the installation video provided below.

Pre-Installation Checks

• Ensure your door thickness is between 35-50mm.
• Verify the backset of your door (distance from door edge to center of bore hole) is compatible. The latch is self-adjusting for bolt side distance.
• If drilling is required for a new door, refer to the drilling drawing provided in the package.

Image: Diagram showing door dimensions and lock measurements, including backset and bore hole diameter, to ensure compatibility.

Installation Steps

1. Install the Latch: Insert the latch into the door edge. Ensure the angle of the latch faces the door jamb. Adjust the backset if necessary, making sure the hole is in the horizontal position.
2. Install the Strike Plate: Secure the strike plate onto the door jamb using the provided screws. Ensure the latch angle faces the door jamb.
3. Install the Exterior Assembly: Slide the shaft of the exterior assembly smoothly through the hole in the latch. Ensure the notch of the lock cylinder is facing away from the door frame. The cable must go through the door hole above the latch.
4. Position the Mounting Plate: Route the cable and connector through the hole in the mounting plate. Position the mounting plate against the door.
5. Secure Assemblies: Secure both the exterior assembly and the mounting plate using the mounting screws.
6. Install the Interior Assembly: Route the cable and connector through the cable hole on the interior assembly. Connect the cable. It is recommended to insert the PCB wire into the door hole after connection. Install the interior assembly and secure it using flat head screws.
7. Install the Handle: Push the lever into the base until the catch pin is engaged. Ensure the tip of the handle points down.
8. Load Batteries and Reset: Install 4x AA batteries into the interior assembly.
9. Install Battery Cover: Put back the lid of the battery pack.

Installation Video Guide

Initial Programming - Change Master Code

The default master code is 12345678. It is required that you change it to a code of your own before programming other features.

1. Press Hugolog button twice, then enter the default master code (12345678), and press Hugolog button again. Wait for a long green light flash.
2. Press 1. Wait for a green light flash.
3. Enter your new master code, then press Hugolog button. Succeed green light flash.
4. Enter the new master code again, then press Hugolog button. Succeed green light flash.

Operating Instructions

Unlocking and Locking

Your Hugolog lock offers multiple ways to unlock and lock for your convenience:

• Keypad: Enter your user code on the keypad.
• Physical Key: Use the provided backup key for manual unlocking.
• Thumb Turn: Rotate the interior thumb turn to manually lock or unlock the door from the inside.

Image: Illustrates three methods of unlocking the door: using the keypad, a physical key, and the interior thumb turn.

Image: Diagram showing how to rotate the interior knob to manually lock or unlock the door, indicating ON and OFF positions.

Adding User Codes

You can add up to 20 user codes for family members or guests.

1. Press Hugolog button twice, then enter your master code, and press Hugolog button again. Wait for a green light flash.
2. Press 2. Wait for a green light flash.
3. Enter the new user code, then press Hugolog button. Succeed green light flash.
4. Enter the new user code again, then press Hugolog button. Succeed green light flash.

Image: Depicts two individuals communicating about setting one-time codes for friend visits, highlighting the ability to set up to 20 temporary codes.

Deleting User Codes

To remove an unwanted user code:

1. Press Hugolog button twice, then enter your master code, and press Hugolog button again. Wait for a green light flash.
2. Press 3. Wait for a green light flash.
3. Enter the unwanted user code, then press Hugolog button. Succeed green light flash.

Auto-Lock Feature

The auto-lock feature automatically locks the door after a set period (10-99 seconds) for added peace of mind.

Image: Shows the auto-lock feature, indicating it allows for a delay from 10 to 99 seconds before automatically locking the door.

Enable Auto-Lock

1. Press Hugolog button twice, then enter your master code, and press Hugolog button again. Wait for a green light flash.
2. Press 5. Wait for a green light flash.
3. Press 1, then press Hugolog button. Succeed green light flash.

Disable Auto-Lock

1. Press Hugolog button twice, then enter your master code, and press Hugolog button again. Wait for a green light flash.
2. Press 5. Wait for a green light flash.
3. Press 2, then press Hugolog button. Succeed green light flash.

Set Auto-Lock Time Delay

1. Press Hugolog button twice, then enter your master code, and press Hugolog button again. Wait for a green light flash.
2. Press 8. Wait for a green light flash.
3. Enter the new duration time (10-99 seconds), then press Hugolog button. Succeed green light flash.

Anti-Peep Password

The anti-peep feature allows you to enter random digits before or after your actual code to prevent others from guessing your code by observing your hand movements.

Image: Illustrates the Anti-Peep Password feature, showing how random digits can be entered before or after the correct code to safeguard against prying eyes.

Silent Mode

Enable silent mode to disable keypad beeps for quiet operation.

Enable Silent Mode

1. Press Hugolog button twice, then enter your master code, and press Hugolog button again. Wait for a green light flash.
2. Press 4. Wait for a green light flash.
3. Press 2, then press Hugolog button. Succeed green light flash.

Disable Silent Mode

1. Press Hugolog button twice, then enter your master code, and press Hugolog button again. Wait for a green light flash.
2. Press 4. Wait for a green light flash.
3. Press 1, then press Hugolog button. Succeed green light flash.

Vacation Mode

Vacation mode disables all user codes, allowing entry only with the master code or physical key. This is useful for extended absences.

Enable Vacation Mode

1. Press Hugolog button twice, then enter your master code, and press Hugolog button again. Wait for a green light flash.
2. Press 6. Wait for a green light flash.
3. Press 1, then press Hugolog button. Succeed green light flash.

Disable Vacation Mode

1. Press Hugolog button twice, then enter your master code, and press Hugolog button again. Wait for a green light flash.
2. Press 6. Wait for a green light flash.
3. Press 2, then press Hugolog button. Succeed green light flash.

Add One-Time Code

Create a temporary code that can be used only once.

1. Press Hugolog button twice, then enter your master code, and press Hugolog button again. Wait for a green light flash.
2. Press 7. Wait for a green light flash.
3. Enter the new user code, then press Hugolog button. Succeed green light flash.
4. Enter the new user code again, then press Hugolog button. Succeed green light flash.

Maintenance

Battery Replacement

The lock requires 4x AA batteries. When the battery level is low, the lock will indicate this with a visual or audible alert. Replace all four batteries simultaneously to ensure optimal performance.

Image: Close-up of the lock's keypad showing a low battery indicator, reminding users to replace the 4x AA batteries for a 1-year battery life.

To replace batteries:

1. Remove the battery cover on the interior assembly.
2. Remove the old batteries.
3. Insert new 4x AA batteries, ensuring correct polarity (+/-).
4. Replace the battery cover.

Note: Always use new, high-quality alkaline batteries for best performance and longevity.

Troubleshooting

If you encounter issues with your Hugolog Keyless Entry Door Lock, please refer to the common problems and solutions below:

Specifications

Warranty and Support

Hugolog provides technical support for hassle-free ownership. For any questions, issues, or warranty claims, please contact Hugolog customer service through their official channels. Please refer to the product packaging or the official Hugolog website for the most up-to-date contact information and warranty details.