Introduction
Thank you for purchasing the Vicks No Touch 3-in-1 Thermometer. This device is designed to provide fast, accurate, and hygienic temperature readings for forehead, food, and bath water. Please read this manual thoroughly before use to ensure proper operation and care.
Image: The Vicks No Touch 3-in-1 Thermometer shown with its retail packaging. The thermometer is white and blue, designed for easy handling.
Product Features
- 3-in-1 Measurement: Measures forehead, food, and bath temperatures.
- No Touch Convenience: Allows for hygienic temperature taking without physical contact.
- Fast Reading System: Provides professional accuracy in approximately 2 seconds.
- Fever InSight Feature: The LED screen displays Green for normal temperature, Yellow for elevated temperature, and Red for high temperature.
- Temperature Units: Readings can be displayed in degrees Fahrenheit (°F) or degrees Celsius (°C).
- Recommended Use: Suitable for infants, children, and adults.
Image: The back of the Vicks No Touch Thermometer box, illustrating key features such as Fever InSight, no-touch convenience, and multi-surface measurement capabilities.
Setup
Unpacking and Battery Installation
The Vicks No Touch Thermometer comes with 2 AAA alkaline batteries included. Follow these steps to install them:
- Locate the battery compartment cover on the back of the thermometer.
- Slide the cover off.
- Insert the 2 AAA alkaline batteries, ensuring correct polarity (+ and -).
- Replace the battery compartment cover until it clicks into place.
Image: The side of the Vicks No Touch Thermometer box, indicating that 2 AAA alkaline batteries are included with the product.
Operating Instructions
Taking a Forehead Temperature
- Ensure the thermometer is in Forehead mode (indicated on the display). If not, press the "MODE" button to switch.
- Position the thermometer approximately 1-2 inches (2.5-5 cm) from the center of the forehead.
- Press and release the power button (measurement button).
- The temperature reading will appear on the display within 2 seconds. The screen color will indicate temperature status (Green: Normal, Yellow: Elevated, Red: High).
Taking Object/Liquid Temperature (Food, Bath Water)
- Press the "MODE" button to switch to Object/Liquid mode.
- Position the thermometer approximately 1-2 inches (2.5-5 cm) from the surface of the object or liquid.
- Press and release the power button (measurement button).
- The temperature reading will appear on the display within 2 seconds.
Switching Temperature Units (°F/°C)
To switch between Fahrenheit and Celsius, refer to the detailed instructions in the full use and care manual. Typically, this involves holding a specific button while the device is off, then powering it on.
Memory Function
The thermometer stores previous readings. Press the "MEMO" button to recall past measurements. Consult the full manual for details on how many readings are stored and how to clear the memory.
Image: A clear front view of the Vicks No Touch Thermometer, showing its display screen and control buttons for mode selection and memory recall.
Maintenance
Cleaning the Thermometer
To ensure accurate readings and hygiene, clean the thermometer regularly:
- Wipe the probe and body of the thermometer with an alcohol swab or a cotton swab moistened with alcohol (70% isopropyl alcohol is recommended).
- Do not immerse the thermometer in water or any other liquid.
- Allow the thermometer to air dry completely before storage or next use.
- Product Care Instructions: Hand Wash Only.
Storage
Store the thermometer in a dry place, away from direct sunlight and extreme temperatures. Remove batteries if the device will not be used for an extended period.
Image: A clear back view of the Vicks No Touch Thermometer, showing the battery compartment and product information label.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Thermometer does not turn on. | Dead or incorrectly installed batteries. | Check battery polarity. Replace with new AAA alkaline batteries. |
| Inaccurate or inconsistent readings. | Improper measurement distance, dirty sensor, or environmental factors. | Ensure correct distance (1-2 inches). Clean the sensor with alcohol. Avoid drafts or extreme temperatures during measurement. Allow thermometer to acclimate to room temperature. |
| Display shows "Lo" or "Hi". | Temperature is outside the measurable range. | Ensure the temperature being measured is within the device's operating range. For forehead, ensure proper placement. |
| Screen color not changing. | Fever InSight feature only applies to forehead temperature mode. | Ensure the thermometer is in forehead mode for the Fever InSight feature to function. |
If problems persist, please contact customer support.
Specifications
- Model Number: VNT200US
- Power Source: 2 x AAA Alkaline Batteries (included)
- Display Type: LED Screen
- Measurement Time: Approximately 2 seconds
- Measurement Modes: Forehead, Object/Liquid
- Temperature Units: Fahrenheit (°F) / Celsius (°C)
- Special Features: Fast Reading System, Fever InSight, Memory Function
- Product Dimensions: Approximately 8 inches (Length)
- Product Weight: Approximately 4.6 ounces
- Usage Environment: Indoor
- Manufacturer: Kaz USA, Inc.
- UPC: 328785002027
Warranty Information
This Vicks No Touch 3-in-1 Thermometer comes with a 1-year limited warranty. For detailed terms and conditions, please refer to the warranty section in the full use and care manual provided with your product or visit the official Vicks Thermometers website.
Support and Contact Information
For questions, comments, or technical support regarding your Vicks No Touch Thermometer, please use the following contact methods:
- Website: www.VicksThermometers.com
- Toll-Free Phone: 1-800-477-0457
- Email: ConsumerRelations@HelenofTroy.com
