1. Important Safety Information
Please read all instructions carefully before assembly and use. Keep this manual for future reference.
⚠ WARNING: This product can expose you to chemical Di(2-ethylhexyl)phthalate (DEHP) and Lead which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov/furniture.
- Ensure all components are present and undamaged before assembly.
- Do not use the product if any parts are missing or damaged.
- Assemble on a soft, clean surface to prevent scratches.
- Do not exceed the maximum weight capacity of 300 pounds.
- Keep children away during assembly.
- Periodically check all fasteners to ensure they remain tight.
2. Package Contents
Verify that all parts listed below are included in your package. If any parts are missing, please contact Yaheetech customer support.
- Seat with backrest (1 or 2, depending on set)
- Gas lift cylinder (1 or 2)
- Base (1 or 2)
- Footrest ring (1 or 2)
- Mounting hardware and tools (screws, Allen wrench)
- Instruction manual
3. Assembly Instructions
Follow these steps carefully to assemble your Yaheetech Bar Stools. Assembly typically takes less than 30 minutes per stool.
- Prepare the Base: Place the large circular base on a flat, stable surface.
- Insert Gas Lift Cylinder: Insert the gas lift cylinder into the center hole of the base. Ensure it is seated firmly.
⚠ Important: Before installation, remove the black plastic protective cap from the top of the gas lift cylinder.
Figure 3.1: Removing the black plastic cap from the gas lift cylinder before assembly.
- Attach Footrest: Slide the footrest ring over the gas lift cylinder and secure it according to the provided hardware.
- Attach Seat to Gas Lift: Align the mounting plate under the seat with the top of the gas lift cylinder. Carefully lower the seat onto the cylinder, ensuring a secure connection. You may need to apply slight pressure.
- Secure Seat: Use the provided screws and Allen wrench to firmly attach the seat to the gas lift mechanism. Ensure all screws are tightened evenly.
Figure 3.2: Exploded view of bar stool components for assembly reference.
4. Operating Instructions
Your Yaheetech Bar Stools are designed for ease of use and comfort.
4.1. Adjusting Height
To adjust the seat height:
- To raise: Stand up from the stool and pull the lever located under the seat upwards. The seat will automatically rise. Release the lever when the desired height is reached.
- To lower: Sit on the stool and pull the lever located under the seat upwards. The seat will lower under your weight. Release the lever when the desired height is reached.
Figure 4.1: Height adjustment and swivel mechanism.
4.2. 360° Swivel Function
The stool seat can rotate 360 degrees, allowing for easy movement and interaction without repositioning the entire stool.
Figure 4.2: Ergonomic seat design and swivel capability.
5. Maintenance
Proper care will extend the life and appearance of your bar stools.
- Cleaning: Wipe the PU leather surface and metal parts with a dry cloth. For stubborn spots, a slightly damp cloth can be used, followed immediately by a dry cloth. Avoid harsh chemicals or abrasive cleaners.
- Inspection: Periodically check all screws and connections to ensure they are tight. Retighten if necessary.
- Protection: The base includes an anti-slip protective rubber ring to prevent scratches on your floor and reduce noise. Ensure this ring remains intact.
6. Troubleshooting
If you encounter any issues, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Stool does not adjust height. | Black plastic cap still on gas lift cylinder. Gas lift cylinder not properly seated. | Ensure the black plastic cap is removed from the gas lift cylinder. Reassemble the gas lift cylinder and seat, ensuring a firm connection. |
| Stool feels wobbly. | Screws are loose. Base is not level. | Check and tighten all assembly screws. Ensure the stool is on a flat, even surface. |
| Difficulty swiveling. | Mechanism needs lubrication or is obstructed. | Ensure no debris is obstructing the swivel mechanism. A small amount of silicone-based lubricant may be applied if necessary (avoid oil-based lubricants on plastic parts). |
7. Specifications
| Feature | Detail |
|---|---|
| Model Number | YTba120001001 |
| Product Dimensions | 19"D x 17"W x 34"H (Adjustable height) |
| Adjustable Seat Height | 24.4" - 33" / 62 - 83.7 cm |
| Seat Width | 17 Inches |
| Base Diameter | 16.3 Inches |
| Maximum Weight Capacity | 300 Pounds |
| Material | High-quality PU Leather, Metal Frame |
| Assembly Required | Yes |
| Product Care | Wipe with Dry Cloth |
Figure 7.1: Bar stool dimensions and weight capacity.
8. Warranty and Support
Yaheetech is committed to providing quality products. For any questions, missing parts, or concerns regarding your bar stools, please contact Yaheetech customer support.
You can find more information and contact details by visiting the official Yaheetech store: Yaheetech Store on Amazon.
Please retain your purchase receipt for warranty purposes.
9. Product Overview
The Yaheetech Bar Stools are designed for versatility and comfort in various settings such as kitchen islands, bars, and dining rooms. They feature a retro-modern design with a brown PU leather surface and a sturdy metal frame.
Figure 9.1: Front view of the Yaheetech Bar Stools.
Figure 9.2: Bar stools in a kitchen island setting.
Figure 9.3: Bar stools paired with a bar table.
10. Video Resources
Currently, no official seller-provided videos are available for embedding in this manual. Please refer to the written instructions and images for guidance.
