Introduction
This manual provides essential information for the proper installation, usage, and maintenance of your Dometic 3106992.062B S/T 45 Degree Bracket Kit. Please read these instructions carefully before proceeding with installation to ensure safe and correct operation. Retain this manual for future reference.
Safety Information
Always observe basic safety precautions when working with tools and hardware. Ensure the installation area is clear and well-lit. Wear appropriate personal protective equipment, such as safety glasses and gloves. If you are unsure about any part of the installation process, consult a qualified professional.
Product Overview
The Dometic 3106992.062B S/T 45 Degree Bracket Kit is an automotive part designed for specific installation requirements. It is supplied as a single unit with a total package weight of 4.0 pounds.
Image: Placeholder for the Dometic 3106992.062B S/T 45 Degree Bracket Kit. This image indicates that a product photo is not yet available.
Setup and Installation
This bracket kit is intended for specific automotive applications. Proper installation is crucial for its function and safety. While specific steps may vary based on the application, general guidelines are provided below.
Tools Required (Typical):
- Wrenches or sockets (appropriate sizes)
- Screwdrivers (Phillips/Flathead, if applicable)
- Measuring tape
- Marking tool
- Drill (if new mounting holes are required)
General Installation Steps:
- Identify Mounting Location: Determine the precise location where the bracket needs to be installed. Refer to your vehicle or appliance's specific service manual for exact positioning.
- Prepare Surface: Ensure the mounting surface is clean, dry, and free from obstructions.
- Position Bracket: Carefully place the 45-degree bracket in the intended position. Verify alignment and orientation.
- Mark Holes: Use the bracket as a template to mark the locations for mounting holes.
- Drill Holes (if necessary): If new holes are required, drill pilot holes of the appropriate size.
- Secure Bracket: Attach the bracket using appropriate fasteners (not included unless specified by Dometic for your application). Ensure all fasteners are tightened securely to the manufacturer's specifications.
- Verify Stability: After installation, gently test the bracket's stability to ensure it is firmly attached and does not wobble.
Usage and Function
The Dometic 3106992.062B S/T 45 Degree Bracket Kit serves as a structural support or mounting component. Once correctly installed, it provides a stable and secure attachment point or structural reinforcement at a 45-degree angle, as per its design. This component does not have active operational functions; its purpose is passive support.
Maintenance
To ensure the longevity and continued performance of your bracket kit, periodic inspection and maintenance are recommended.
- Regular Inspection: Periodically check the bracket and its mounting points for any signs of wear, corrosion, or loosening of fasteners.
- Cleaning: Clean the bracket with a mild soap and water solution, then rinse thoroughly and dry. Avoid abrasive cleaners or solvents that could damage the finish.
- Tighten Fasteners: Re-tighten any loose fasteners to prevent movement or failure.
- Corrosion Protection: If installed in an environment prone to corrosion, consider applying a suitable corrosion-inhibiting coating or lubricant to exposed metal parts, if appropriate for the material.
Troubleshooting
Most issues related to a bracket kit are typically associated with installation or physical damage.
- Bracket is Loose: Check all mounting fasteners. Ensure they are tightened to the correct torque. Inspect the mounting surface for damage or instability.
- Bracket is Damaged: If the bracket shows signs of bending, cracking, or severe corrosion, it should be replaced immediately to prevent potential failure.
- Incorrect Angle/Position: Re-evaluate the installation steps and ensure the bracket is positioned and oriented correctly according to your application's requirements.
Specifications
| Manufacturer | Dometic |
| Brand | Dometic |
| Model Number | 106992062B |
| Part Number | 3106992.062B |
| Product Type | AUTO PART |
| Item Package Quantity | 1 |
| Item Package Weight | 4.0 Pounds |
| ASIN | B085MLQFN6 |
| Date First Available | March 7, 2020 |
Warranty and Support
For specific warranty information regarding the Dometic 3106992.062B S/T 45 Degree Bracket Kit, please refer to the documentation provided with your original purchase or visit the official Dometic website. For technical support or assistance with installation, contact Dometic customer service directly.
