Casio TQ-169-7JF Analog Alarm Clock User Manual

1. Introduction

This manual provides instructions for the proper use and maintenance of your Casio TQ-169-7JF Analog Alarm Clock. This compact, square-shaped analog alarm clock is designed for ease of use and portability, featuring essential functions for daily timekeeping and alarms.

Key Features:

• Electronic sound alarm with tempo-increasing snooze function.
• LED light for dial illumination, allowing time checks in low-light conditions.
• High-intensity LED mini light for convenient searching in the dark.
• Easy-to-read analog display with a step second hand movement.
• Compact and portable design, suitable for various locations and travel.

Figure 1: Front view of the Casio TQ-169-7JF Analog Alarm Clock, showcasing its white square design and clear analog dial.

2. Important Safety Information

Please read and understand all safety precautions before using this product. Failure to follow these instructions may result in injury or damage to the product.

• Battery Safety: If battery liquid leaks and comes into contact with skin or clothing, rinse immediately with clean water. Keep batteries out of reach of infants and children.
• Placement: Do not place or use the clock in the following environments:
• Areas with high humidity or excessive dust.
• Kitchens, near humidifiers, or other areas exposed to oil smoke or steam.
• Near heating equipment, on hot carpets, in direct sunlight, or inside vehicles exposed to high temperatures.
• On unstable surfaces where the clock could fall.
• Modification: Do not disassemble or modify the product. Unauthorized modifications can lead to malfunction or injury.

3. Setup

3.1. Battery Installation

The Casio TQ-169-7JF alarm clock requires one (1) AA alkaline battery (included). Follow these steps to install the battery:

1. Locate the battery compartment cover on the back of the clock.
2. Slide or lift the cover to open the compartment.
3. Insert one AA alkaline battery, ensuring the positive (+) and negative (-) terminals are aligned correctly according to the diagram inside the compartment.
4. Replace the battery compartment cover securely.

Figure 2: Rear view of the alarm clock, illustrating the battery compartment and control knobs for time and alarm settings.

4. Operating Instructions

4.1. Setting the Current Time

To set the current time on your analog clock:

1. Locate the Time Setting Knob on the back of the clock (refer to Figure 2).
2. Rotate the knob in either direction until the hour and minute hands display the correct current time.

4.2. Setting the Alarm Time

To set the desired alarm time:

1. Locate the Alarm Setting Knob on the back of the clock (refer to Figure 2). This is typically a smaller knob or a knob with a different texture than the time setting knob.
2. Rotate the alarm setting knob until the alarm hand points to your desired wake-up time.
3. To activate the alarm, slide the Alarm ON/OFF Switch (usually on the side or back) to the "ON" position. To deactivate, slide it to "OFF".

4.3. Snooze Function

When the alarm sounds, press the large button located on the top of the clock to activate the snooze function. The alarm will temporarily stop and sound again after a short interval, with an increasing tempo to ensure you wake up.

4.4. Light Functions

Your clock is equipped with two lighting features:

• LED Dial Light: Press the large button on the top of the clock (the same button as snooze) to illuminate the clock face for a few seconds, allowing you to check the time in the dark.
• Mini Light (High-Intensity LED): A separate mini light is integrated into the clock. This high-intensity LED is useful for briefly illuminating small areas or finding items in the dark. The activation method for the mini light is typically a dedicated button on the side or top of the clock.

Figure 3: Illustration of the clock's two light functions: the LED dial light for checking time and the high-intensity mini light for general illumination in dark environments.

5. Maintenance

5.1. Cleaning

To clean your alarm clock, wipe it gently with a soft, dry cloth. Do not use abrasive cleaners, solvents, or chemical sprays, as these can damage the clock's finish or internal components.

5.2. Battery Replacement

When the clock's display dims, the alarm sound weakens, or the clock stops functioning, it is time to replace the battery. Refer to Section 3.1 for battery installation instructions. Always use a fresh AA alkaline battery for optimal performance.

6. Troubleshooting

If you experience issues with your Casio TQ-169-7JF alarm clock, please refer to the following common problems and solutions:

• Clock is not working or hands are not moving:
• Check if the battery is installed correctly with the correct polarity (+/-).
• Replace the battery with a fresh AA alkaline battery.
• Alarm is not sounding:
• Ensure the Alarm ON/OFF switch is in the "ON" position.
• Verify that the alarm time is set correctly.
• Check the battery as a weak battery can affect alarm volume.
• Lights are not working:
• Ensure the battery has sufficient power. Replace if necessary.
• Confirm you are pressing the correct button for each light function.

If problems persist after attempting these solutions, please contact Casio customer support for further assistance.

7. Specifications

Figure 4: Dimensions of the Casio TQ-169-7JF alarm clock, showing its compact size of approximately 7.6cm height, 7.7cm width, and 3.7cm depth.

8. Warranty and Support

For information regarding product warranty, please refer to the warranty card included with your purchase or visit the official Casio website. For technical support or inquiries, please contact Casio customer service through their official channels.

You can find more information and support resources on the Casio Store on Amazon.