Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your Moen Wynford 655BN Freestanding Tub Filler with Handshower. Please read all instructions carefully before beginning installation or use to ensure proper function and longevity of the product.
The Moen Wynford Freestanding Tub Filler features a durable LifeShine Brushed Nickel finish, designed to resist tarnishing and corrosion. It is built on the Moen M-PACT common valve system, allowing for future style updates without requiring changes to your plumbing. The unit includes an Eco-Performance handshower with a 1.75 gallons per minute (gpm) flow rate and offers both a lever and cross handle for personalized control.
Setup and Installation
Required Components (Sold Separately)
- Moen Single Riser Floor Mounting Kit (Model TS50100 or TS50110)
Important: A Moen single riser floor mounting kit (TS50100 or TS50110) is required for the proper installation of this freestanding tub filler. This kit must be purchased separately.
Installation Overview
Installation of the Moen Wynford Freestanding Tub Filler involves securing the required floor mounting kit, connecting water supply lines, and then attaching the tub filler body. Professional installation is recommended to ensure compliance with local plumbing codes and proper functionality.
Image: The required valve assembly for the Moen freestanding tub filler. This component is essential for securing the faucet to the floor and connecting water lines.
General Installation Steps (Consult full instructions provided with mounting kit)
- Prepare the Installation Area: Ensure the floor is clear and structurally sound to support the tub filler. Mark the precise location for the mounting kit.
- Install the Mounting Kit: Follow the specific instructions provided with your Moen TS50100 or TS50110 floor mounting kit to secure it to the subfloor. This typically involves cutting a precise hole and fastening the bracket.
- Connect Water Supply: Connect the hot and cold water supply lines to the valve assembly within the mounting kit. Ensure all connections are tight and leak-free.
- Install the Tub Filler Body: Carefully place the tub filler body onto the installed mounting kit, aligning it with the valve assembly. Secure the tub filler to the mounting kit according to the kit's instructions.
- Test for Leaks: Turn on the water supply and thoroughly check all connections for any leaks.
Operating Instructions
The Moen Wynford tub filler features a single handle for controlling both water temperature and flow, along with a diverter for the handshower.
Image: The Moen Wynford Freestanding Tub Filler, showing the main handle and handshower.
Controlling Water Flow and Temperature
- Turn On/Off: Lift the main handle to turn on the water flow. Push down to turn off.
- Adjust Flow: The height to which the handle is lifted controls the water volume.
- Adjust Temperature: Rotate the handle left for hotter water and right for colder water.
Using the Handshower
- Activate Handshower: Pull the diverter knob located on the tub filler body to redirect water flow from the main spout to the handshower.
- Return to Spout: Push the diverter knob back in to return water flow to the main tub spout.
Maintenance
Cleaning the Finish
To maintain the LifeShine Brushed Nickel finish, clean with a soft, damp cloth. Avoid abrasive cleaners, harsh chemicals, or polishing agents, as these can damage the finish and void your warranty.
Aerator Maintenance
If water flow decreases, the aerator may be clogged. Unscrew the aerator from the spout, clean any debris, and rinse thoroughly before reattaching.
Troubleshooting
If you encounter issues with your tub filler, refer to the following common solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Low Water Flow | Clogged aerator; partially closed shut-off valves. | Clean the aerator. Ensure hot and cold water shut-off valves are fully open. |
| Leaking from Spout/Handle | Loose connections; worn O-rings or cartridge. | Check and tighten all connections. If problem persists, contact Moen support for replacement parts or service. |
| Handshower Not Diverting | Diverter mechanism issue. | Ensure the diverter knob is fully pulled. If still not diverting, contact Moen support. |
For issues not listed here or if troubleshooting steps do not resolve the problem, please contact Moen customer support.
Specifications
| Feature | Detail |
|---|---|
| Brand | Moen |
| Model Number | 655BN |
| Color | Brushed Nickel |
| Material | Steel |
| Finish Type | Brushed |
| Number of Handles | 1 |
| Mounting Type | Floor Mount |
| Included Components | Floor mount tub filler faucet, handshower, hose |
| Item Weight | 23.8 pounds |
| Spout Reach | 9.75 inches |
| UPC | 026508298411 |
Warranty Information
This Moen product is backed by Moen's Limited Lifetime Warranty. This warranty covers defects in material and manufacturing workmanship for the original consumer purchaser. Please refer to the official Moen website or the warranty card included with your product for full terms and conditions.
Customer Support
For technical assistance, replacement parts, or warranty claims, please contact Moen customer service. Contact information can be found on the official Moen website or on the packaging of your product.
Moen Official Website: www.moen.com
