Boly SG2060-T Trail Camera: User Instruction Manual

1. Introduction

This manual provides comprehensive instructions for the setup, operation, maintenance, and troubleshooting of your Boly SG2060-T Trail Camera. Designed for outdoor surveillance and wildlife monitoring, this camera captures high-resolution images and videos with advanced detection capabilities. Please read this manual thoroughly before using the camera to ensure proper function and longevity.

Figure 1.1: Boly SG2060-T Trail Camera (Front View)

The image displays the front of the Boly SG2060-T Trail Camera, featuring a camouflage pattern. Visible components include the lens, motion sensor, and an array of LED and Xenon flash lights at the top, designed for night vision and illumination.

2. Product Components and Features

The Boly SG2060-T Trail Camera is equipped with several key components and features to ensure optimal performance in various outdoor conditions.

Figure 2.1: Internal and External Components

This image illustrates the key components of the camera. The top view shows the LCD display, battery bays, and operation panel. The bottom view highlights the DC input, USB port, TV out port, SD card slot, DC hole, stopper, and bottom screw for mounting.

Key Features:

• Image Resolution: Full color 48MP picture resolution.
• Video Resolution: 1080p HD video with audio.
• Detection Range: Up to 100 feet.
• Flash Range: 90 feet with Xenon strobe flash and IR LED for night vision.
• Display: Integrated 2.0-inch TFT LCD viewer.
• Storage: Supports up to 64GB SD Card (not included).
• Power: Operates on 8 AA batteries (not included) or external power options.
• Durability: IP54 International Protection Rating, resistant to water and snow.
• Technology: Features Motion Sharp technology and patented PIR (passive infrared) Fresnel lens for enhanced sensitivity.

3. Setup Guide

Follow these steps to prepare your Boly SG2060-T Trail Camera for use.

3.1. Battery Installation

1. Open the camera casing by unlatching the side clips.
2. Locate the battery compartment.
3. Insert 8 AA batteries (alkaline or rechargeable NiMH recommended) into the battery bays, ensuring correct polarity (+/-).
4. Close the battery compartment cover securely.

Figure 3.1: Battery Compartment and Controls

The image shows the camera opened, revealing the battery compartment on the right side and the control panel with LCD screen on the left side.

3.2. SD Card Insertion

1. With the camera casing open, locate the SD card slot on the side of the control panel.
2. Insert an SD or SDHC card (up to 64GB, Class 10 or higher recommended) into the slot until it clicks into place. Ensure the card is inserted in the correct orientation.
3. To remove, gently push the card in until it springs out.

3.3. Initial Power On and Basic Settings

1. Slide the mode switch from 'OFF' to 'SETUP'. The LCD screen will power on.
2. Use the navigation buttons (UP, DOWN, LEFT, RIGHT, OK) to navigate the menu.
3. Go to the 'Settings' menu to set the current date, time, and other basic parameters. This is crucial for accurate timestamping of captured media.
4. Format the SD card through the camera's menu system before first use to ensure compatibility and optimal performance.

3.4. Mounting the Camera

The camera can be mounted using the included strap or a tripod/wall mount.

• Strap Mounting: Thread the provided mounting strap through the slots on the back of the camera. Secure the camera to a tree or post at the desired height and angle.
• Tripod/Wall Mount: Use the 1/4-20 threaded insert at the bottom of the camera to attach it to a tripod or a compatible wall mount bracket (sold separately).

4. Operating Instructions

Understand the different operating modes and how to capture media with your camera.

4.1. Mode Switch

• OFF: Powers off the camera.
• SETUP: Allows access to the camera's menu, settings, and playback of captured media. The camera will not detect motion or record in this mode.
• ON: Activates the camera for motion detection and recording. The LCD screen will turn off after a few seconds to conserve power, and the camera will enter monitoring mode.

4.2. Menu Navigation and Settings

In 'SETUP' mode, use the following buttons:

• MENU: Enters or exits the main menu.
• UP/DOWN: Navigates through menu options.
• LEFT/RIGHT: Changes values or sub-options.
• OK: Confirms selection.
• DEL: Deletes selected files during playback.

Key settings to configure:

• Mode: Select Photo, Video, or Photo+Video.
• Resolution: Set desired photo (up to 48MP) and video (1080p) resolution.
• PIR Sensitivity: Adjust for detection range (High, Normal, Low).
• Trigger Interval: Set the delay between detections.
• Time Lapse: Configure if desired for specific monitoring scenarios.

4.3. Capturing Photos and Videos

Once settings are configured, slide the mode switch to 'ON'. The camera will automatically begin monitoring. When motion is detected within the 100ft range, the camera will trigger and capture images or video according to your settings. The 90ft flash range ensures clear captures even in low light or complete darkness.

4.4. Viewing Captured Media

To view photos and videos:

1. Slide the mode switch to 'SETUP'.
2. Press the playback button (often indicated by a play icon or 'OK' in playback mode).
3. Use the navigation buttons to scroll through files.
4. Press 'OK' to view a photo or play a video.
5. You can also remove the SD card and view media on a computer using a card reader.

5. Maintenance

Proper maintenance ensures the longevity and optimal performance of your trail camera.

5.1. Cleaning

• Gently wipe the camera lens and PIR sensor window with a soft, lint-free cloth. Avoid abrasive materials that could scratch the surfaces.
• Clean the camera casing with a damp cloth. Do not use harsh chemicals or solvents.
• Ensure the battery compartment and SD card slot are free of dust and debris.

5.2. Battery Management

• Replace batteries when the low battery indicator appears on the LCD screen.
• If the camera will not be used for an extended period, remove the batteries to prevent leakage and damage.
• Consider using high-quality alkaline or rechargeable NiMH batteries for best performance and environmental impact.

5.3. SD Card Management

• Regularly back up important files from your SD card to a computer or external storage device.
• Format the SD card periodically (e.g., once a month or after significant use) through the camera's menu to maintain optimal performance and prevent data corruption.

5.4. Storage

• When not in use, store the camera in a cool, dry place away from direct sunlight and extreme temperatures.
• Ensure the casing is securely latched to protect internal components.

6. Troubleshooting

This section addresses common issues you might encounter with your Boly SG2060-T Trail Camera.

7. Technical Specifications

Detailed specifications for the Boly SG2060-T Trail Camera.

8. Warranty and Support

Boly products are designed for reliability and performance. For specific warranty details regarding your SG2060-T Trail Camera, please refer to the warranty card included with your purchase or visit the official Boly website. In case of technical issues or questions not covered in this manual, please contact Boly customer support for assistance.

Boly Customer Support:

• Refer to the contact information provided on the product packaging or the official Boly website (www.bolymedia.com) for the most up-to-date support channels.