Introduction
This manual provides essential instructions for the installation, operation, and maintenance of the Gecko Aeware in.XE Spa Pack Control, model 0602-221063-299. The in.XE is an integrated control system designed for entry-level spas, featuring a heat.wav integrated heater and various connection points for spa components. Please read this manual thoroughly before installation and use to ensure proper function and safety.
Safety Information
Important Safety Instructions:
- Installation must be performed by a qualified electrician in accordance with all local and national electrical codes.
- Disconnect all power to the spa before performing any service or maintenance.
- Do not operate the spa pack if any part is damaged or appears to be malfunctioning.
- Ensure proper grounding and bonding of all spa components.
- Keep the spa pack enclosure dry and free from moisture.
- Refer to the spa manufacturer's instructions for specific wiring diagrams and component compatibility.
Product Overview
This image displays the Gecko Aeware in.XE Spa Pack Control unit. The main blue housing contains the control electronics, with various colored ports for connections visible on the right side. Below the main housing is the integrated heat.wav heater, a cylindrical stainless steel component with white pipe connections on either end.
The Gecko Aeware in.XE Spa Pack Control is an advanced system designed to manage the various functions of your spa. It integrates a control unit with a heat.wav heater, providing a compact and efficient solution. Key features include multiple AC connectors for pumps, blowers, and ozonators, as well as low-voltage connections for keypads, communication links, and lighting.
Setup and Installation
Proper installation is critical for the safe and efficient operation of your spa pack. Always consult a qualified professional for installation.
Electrical Connections:
- High-Current AC Connectors:
- Pump 1
- Pump 2
- Low-Current AC Connectors (Relay Controlled):
- Blower
- Ozonator
- Direct-to-Line:
- In.power.210 power supply
- Low-Voltage Interface Connections:
- Keypad
- Communication link
- Light output
Heater Installation:
The integrated heat.wav heater is designed for 4kW operation at 240V. Ensure proper plumbing connections and water flow through the heater element before powering on the unit.
Typical Spa Configurations:
- Dual pumps
- Dual pumps and blower
- Single pump
- Single pump and blower
Consult the specific wiring diagram provided with your spa or by Gecko for detailed connection instructions.
Operating Instructions
Once installed and powered, the in.XE spa pack control manages the various functions of your spa. Operation is typically performed through a compatible keypad (connected via the low-voltage interface). Refer to your specific keypad's user manual for detailed instructions on controlling pumps, blowers, lights, and temperature settings.
- Power On: Ensure all connections are secure and the spa is filled with water before applying power.
- Temperature Control: Use the keypad to set your desired water temperature.
- Jet Operation: Activate pumps for jets via the keypad.
- Blower/Ozonator: Control these accessories through the keypad interface.
- Lighting: Adjust spa lighting as desired.
Maintenance
Regular maintenance helps ensure the longevity and optimal performance of your spa pack.
- Visual Inspection: Periodically inspect the spa pack for any signs of damage, corrosion, or loose connections.
- Keep Dry: Ensure the spa pack enclosure remains dry and protected from water ingress.
- Heater Element: Check the heater element for scale buildup or damage during routine spa maintenance. Proper water chemistry is essential to prevent scaling.
- Professional Check: It is recommended to have a qualified technician inspect the spa pack annually.
Troubleshooting
If you encounter issues with your spa pack, consider the following basic troubleshooting steps:
- No Power:
- Check the main circuit breaker for the spa.
- Verify all electrical connections to the spa pack are secure.
- Heater Not Working:
- Ensure there is adequate water flow through the heater. Low flow can trigger safety cut-offs.
- Check for error codes on the keypad (refer to keypad manual).
- Verify the temperature setting is above the current water temperature.
- Pump/Blower Not Activating:
- Check keypad for activation.
- Listen for any humming sounds from the pump/blower, which might indicate a seized motor.
- Verify connections to the spa pack.
- Error Codes: Consult your keypad's user manual for explanations of specific error codes displayed.
For complex issues or if troubleshooting steps do not resolve the problem, contact a qualified spa technician or Gecko customer support.
Specifications
| Brand | Gecko |
| Model Name | in.xe |
| Item Model Number | 0602-221063-299 |
| UPC | 709951011478 |
| Product Dimensions | 64.9"L x 64.9"W x 27.5"H (Note: This dimension seems unusually large for a spa pack and might refer to a complete spa. Please verify with manufacturer specifications.) |
| Item Weight | 12.32 pounds |
| Material | Plastic (housing) |
| Power Source | AC |
| Heater Output | 4kW @ 240V |
| AC Connectors | 2 high-current (Pump 1, Pump 2), 3 low-current (Blower, Ozonator, In.power.210) |
| Low-Voltage Connections | Keypad, Communication link, Light output |
Warranty Information
Specific warranty terms and conditions for the Gecko Aeware in.XE Spa Pack Control are provided by the manufacturer. Please refer to the documentation included with your purchase or contact Gecko directly for detailed warranty information. Keep your proof of purchase for warranty claims.
Support
For technical assistance, troubleshooting beyond this manual, or warranty inquiries, please contact:
- Gecko Customer Support: Refer to the official Gecko website or product packaging for contact details.
- Your Authorized Dealer: The retailer or installer from whom you purchased the spa pack.
When contacting support, please have your model number (0602-221063-299) and serial number (if applicable) ready.
