BoxWave ClearTouch Anti-Glare Screen Protector User Manual

1. Introduction and Product Overview

The BoxWave ClearTouch Anti-Glare Screen Protector is designed to protect the screen of your Getac ZX70 device while enhancing visibility in various lighting conditions. This manual provides detailed instructions for installation, usage, maintenance, and troubleshooting to ensure optimal performance and longevity of your screen protector.

Key Features:

• Anti-Glare: Dramatically reduces screen glare for maximum visibility under sunlight and other harsh lighting conditions.
• Anti-Fingerprint: Protects your screen from fingerprints, dust, and smudges.
• Precision Fit: Engineered with precision to fit the exact dimensions of your Getac ZX70.
• Scratch Protection: Dual-layered high-grade PET film designed for durability, protecting your screen from scratches.
• Glueless Adhesive: Special adhesive bonds perfectly to your screen and leaves no sticky residue upon removal.
• Reusable: Can be re-used by washing with warm water and hand soap to renew adhesive quality.
• UV Protection: Reduces 90% of UV rays caused by reflected light, protecting your eyes.

Image 1.1: The BoxWave ClearTouch Anti-Glare Screen Protector applied to a Getac ZX70 device, showcasing its precise fit and anti-glare properties.

2. Setup and Installation

Proper installation is key to the performance and longevity of your screen protector. Please follow these steps carefully.

Included Accessories:

• ClearTouch Anti-Glare Screen Protectors (2-Pack)
• ClearTouch Applicator Card
• Microfiber Cleaning Cloth
• Dust Removing Sticker (not explicitly listed in bullets but implied by image)

Image 2.1: The essential tools included for screen protector installation: an applicator card, a microfiber cleaning cloth, and a dust removing sticker.

Installation Steps:

1. Clean Your Device Screen: Use the included microfiber cleaning cloth to thoroughly clean the Getac ZX70 screen. Ensure there are no dust particles, smudges, or fingerprints. For stubborn marks, a screen cleaner (not included) can be used, followed by drying with the microfiber cloth.
2. Remove Dust: Use the dust removing sticker to lift any remaining dust particles from the screen. This step is crucial for a bubble-free installation.
3. Peel Back Layer 1: Carefully peel back the protective layer labeled '1' from the screen protector, exposing the adhesive side. Avoid touching the adhesive surface.
4. Align and Apply: Align the screen protector with the edges of your Getac ZX70 screen. Start from one edge and slowly lower the protector onto the screen. Ensure precise alignment, especially around the camera and sensors.
5. Smooth Out Bubbles: Once the protector is laid down, use the ClearTouch Applicator Card to gently push out any air bubbles towards the edges of the screen. Apply firm, even pressure.
6. Remove Layer 2: Once the screen protector is fully adhered and bubbles are minimized, carefully peel off the top protective layer labeled '2'.

Image 2.2: Illustration of the screen protector's coverage area on the Getac ZX70, indicating the precise fit within the device's display.

Note: The special low-tack adhesive may take a short period to fully adhere around the edges. Any small air gaps present immediately after installation will typically clear out within approximately 2 days of regular use.

3. Operating and Usage Benefits

Once installed, your BoxWave ClearTouch Anti-Glare Screen Protector provides continuous protection and enhances your device's usability.

Daily Use Benefits:

• Reduced Glare: Enjoy improved screen visibility, especially in bright environments like outdoors or under strong indoor lighting.
• Fingerprint Resistance: The matte surface repels unwanted smudges and fingerprints, keeping your screen cleaner.
• Enhanced Touch Experience: The screen protector maintains the original touch sensitivity of your Getac ZX70.
• Paper-like Feel: The matte finish can provide a tactile experience similar to writing or drawing on paper, which can be beneficial for stylus users.

Image 3.1: Demonstrates the 'paper-like feel' of the screen protector, allowing for a natural writing and drawing experience with a stylus.

Image 3.2: A visual comparison highlighting the anti-smudge properties of the BoxWave screen protector versus a standard surface, showing reduced fingerprint visibility.

4. Maintenance

To keep your BoxWave ClearTouch Anti-Glare Screen Protector in optimal condition, follow these simple maintenance guidelines.

Cleaning the Screen Protector:

• For daily cleaning, gently wipe the screen protector with the included microfiber cleaning cloth to remove dust and light smudges.
• For more persistent marks, lightly dampen the microfiber cloth with water or a screen-safe cleaning solution and wipe the surface. Avoid harsh chemicals or abrasive materials.

Reusability:

One of the unique features of the ClearTouch Anti-Glare screen protector is its reusability. If the adhesive loses its stickiness or if the protector needs to be repositioned after a long period, you can renew its adhesive quality:

1. Carefully peel the screen protector off your device.
2. Wash the adhesive side of the screen protector with warm water and a small amount of mild hand soap.
3. Rinse thoroughly under running water to remove all soap residue.
4. Allow the screen protector to air dry completely, adhesive side up, in a dust-free environment. Do not wipe with a cloth as this may leave lint.
5. Once dry, the adhesive quality should be restored, and you can re-install the protector following the steps in Section 2.

5. Troubleshooting

If you encounter any issues during or after installation, refer to the following common problems and their solutions.

Common Issues and Solutions:

6. Specifications

Detailed technical specifications for the BoxWave ClearTouch Anti-Glare Screen Protector.

7. Warranty and Support

For information regarding product warranty, returns, or technical support, please contact BoxWave Corporation directly. Details are typically available on the product packaging or the official BoxWave website.

Manufacturer: BoxWave Corporation

Please retain your purchase receipt for any warranty claims.