Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of the Aiphone TD-6H/B Selective Call Intercom. Please read this manual thoroughly before using the product to ensure correct usage and optimal performance. Keep this manual for future reference.
Important Safety Information
Observe the following safety precautions to prevent damage to the product and ensure user safety:
- Do not expose the unit to rain or moisture.
- Do not open the unit. Refer all servicing to qualified personnel.
- Ensure proper wiring connections as specified in the installation section.
- Use only specified power sources and accessories.
Product Overview
The Aiphone TD-6H/B is a selective call handset master station designed for clear and reliable internal communication. It allows users to selectively call other stations within the intercom system.
Figure 1: Front view of the Aiphone TD-6H/B handset. This image displays the main body of the intercom unit, including the handset receiver, the base with multiple numbered call buttons (1-6), and a 'CALL' button. The Aiphone logo and 'TD-6H' model designation are visible above the buttons.
Figure 2: Side view of the Aiphone TD-6H/B handset. This image provides a perspective of the intercom unit from the side, highlighting the ergonomic design of the handset and the coiled cord that connects it to the main base unit. The base unit's profile with the call buttons is also visible.
Setup and Installation
1. Mounting the Unit
The TD-6H/B unit is designed for wall mounting. Ensure the mounting surface is stable and can support the unit's weight. Use appropriate screws and anchors for installation.
2. Wiring Connections
Before making any connections, ensure the power supply to the intercom system is disconnected. Refer to the wiring diagram for correct terminal connections.
Figure 3: Rear view of the Aiphone TD-6H/B Intercom base. This image shows the back panel of the intercom unit, revealing the terminal block for wiring connections. The internal circuitry and mounting points are also visible, along with a label indicating 'MODEL TD-6H/B' and 'MADE IN CHINA'.
- Connect the main power supply wires to the designated power terminals.
- Connect the communication wires from other intercom stations to their respective numbered terminals (e.g., station 1 to terminal 1, station 2 to terminal 2, etc.).
- Ensure all connections are secure and properly insulated.
3. Initial Power-Up
Once all connections are made and verified, restore power to the intercom system. The unit should power on without any indicators of malfunction.
Operating Instructions
1. Making a Call
- Lift the handset from the cradle.
- Press the numbered button corresponding to the station you wish to call.
- Press the CALL button. The called station will receive an audible alert.
- Speak into the microphone on the handset.
- When the conversation is complete, return the handset to its cradle.
2. Receiving a Call
- When an incoming call is received, the unit will emit an audible ring.
- Lift the handset to answer the call.
- Speak into the microphone on the handset.
- When the conversation is complete, return the handset to its cradle.
3. Volume Adjustment
The listening volume can typically be adjusted via a small dial or switch located on the side or bottom of the handset or base unit. Refer to the specific markings on your unit for exact location and operation.
Maintenance
1. Cleaning
To clean the unit, wipe it with a soft, dry cloth. For stubborn dirt, a slightly damp cloth with mild soap can be used, followed by a dry cloth. Do not use abrasive cleaners, solvents, or strong detergents, as these can damage the finish.
2. General Care
- Avoid dropping the unit or subjecting it to strong impacts.
- Keep the unit away from direct sunlight, high temperatures, and excessive humidity.
- Ensure the coiled cord is not stretched excessively or tangled, which could lead to damage.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| No power to the unit. | Power supply disconnected or faulty. | Check power connections and ensure the power source is active. |
| Cannot hear or be heard. | Handset not properly seated; volume too low; faulty wiring. | Ensure handset is on-hook then off-hook; adjust volume; check wiring connections. |
| Cannot call a specific station. | Incorrect button pressed; wiring issue to that station. | Verify the correct station button is pressed; inspect wiring to the target station. |
| Interference or static during calls. | Loose wiring; external electrical interference. | Check all wiring connections for tightness; relocate unit away from strong electrical devices if possible. |
Specifications
Figure 4: Model label for the Aiphone TD-6H/B. This image provides a clear view of the product's identification label, which states 'MODEL TD-6H/B', 'LOT NO. CG54122 R', 'Inspected', and 'MADE IN CHINA'. The Aiphone Co., Ltd. logo is also visible.
Figure 5: Packaging for the Aiphone TD-6H/B. This image shows the product's retail packaging, prominently displaying 'TD-6H/B', 'MADE IN CHINA', and various compliance logos (RoHS, WEEE). Both the UPC (0790143447724) and EAN (4968249447726) barcodes are clearly visible.
Figure 6: Product identification label. This label confirms the product as 'AIPHONE TD-6H/B SELECTIVE CALL INTERCOM COMMUNICATION' and includes a part number 'D530396'.
- Model: TD-6H/B
- Manufacturer: AIPHONE
- Product Dimensions: 12.25 x 6.5 x 5.25 inches
- Item Weight: 1.3 pounds
- ASIN: B01GS21VLU
- Part Number: D530396
- UPC: 0790143447724
- EAN: 4968249447726
- Date First Available: June 8, 2016
Warranty Information
Aiphone products are typically covered by a limited warranty against defects in materials and workmanship. The specific terms and duration of the warranty may vary. Please refer to the official Aiphone website or contact their customer support for detailed warranty information applicable to your region and purchase date.
Customer Support
For technical assistance, troubleshooting beyond this manual, or warranty claims, please contact Aiphone customer support. Contact information can typically be found on the official Aiphone website or on the product packaging.