EGLO 201222A
EGLO Lianello 31" 4-LED Dimmable Track Light Instruction Manual
Model: 201222A
Introduction
This manual provides essential instructions for the safe installation, operation, and maintenance of your EGLO Lianello 31" 4-LED Dimmable Track Light, Model 201222A. Please read this manual thoroughly before proceeding with installation or use, and retain it for future reference.
The EGLO Lianello track light features a modern design with adjustable lamp heads, allowing for directed illumination. It incorporates integrated LED technology and is compatible with dimmer switches.
Important Safety Information
- Always disconnect power at the main circuit breaker before installation or maintenance.
- Installation must be performed by a qualified electrician in accordance with all local electrical codes.
- Ensure the mounting surface can support the weight of the fixture.
- Do not attempt to modify the fixture. Any modifications will void the warranty and may create a safety hazard.
- This fixture is primarily designed for indoor use in areas such as kitchens, hallways, and dining rooms. While some specifications may indicate outdoor suitability, please consult a qualified professional if intended for outdoor environments to ensure compliance with specific outdoor electrical requirements.
- Do not look directly into the LED light source.
- Keep packaging materials away from children.
Package Contents
Verify that all components are present and undamaged before beginning installation.
- EGLO Lianello 31" 4-LED Dimmable Track Light Fixture (Model 201222A)
- Mounting Hardware (screws, wire nuts, etc.)
- Instruction Manual
Note: Additional tools required for installation (not included): screwdriver, wire strippers, drill, ladder, safety glasses.
Setup and Installation
This fixture is designed for mounting on walls or ceilings. Professional installation is recommended.
Step 1: Prepare for Installation
- Turn off power: Locate the circuit breaker controlling the light fixture's location and switch it to the OFF position. Verify power is off using a voltage tester.
- Unpack contents: Carefully remove all components from the packaging.
- Review instructions: Read through all steps before beginning.
Step 2: Mounting the Fixture
The fixture can be mounted horizontally or vertically. The mounting plate should be secured to a junction box.

Image: The EGLO Lianello track light shown mounted horizontally on a ceiling. This configuration is suitable for general room illumination or highlighting areas below.

Image: The EGLO Lianello track light shown mounted vertically on a wall. This configuration can be used to illuminate wall art or provide accent lighting.
- Attach mounting plate: Secure the fixture's mounting plate to the electrical junction box using the provided screws. Ensure it is firmly attached.
- Electrical connections: Connect the fixture's wires to the household electrical wires according to local codes. Typically, connect black to black (live), white to white (neutral), and green/bare copper to green/bare copper (ground) using wire nuts.
- Secure fixture: Carefully push the wired connections into the junction box and attach the fixture body to the mounting plate, securing it with the provided screws or fasteners.
Step 3: Adjusting Lamp Heads
The four LED lamp heads are adjustable, allowing you to direct light as needed.

Image: The EGLO Lianello track light installed in a retail environment, demonstrating how the adjustable heads can be angled to spotlight specific items like clothing on mannequins.
- Restore power: Once installation is complete and secure, return to the main circuit breaker and switch the power back ON.
- Test fixture: Turn on the light switch to ensure the fixture is working correctly.
- Adjust light direction: Gently pivot and rotate each lamp head to direct the light beam to your desired area. Do not force the heads beyond their natural range of motion.
Operating Instructions
Turning On/Off
Operate the EGLO Lianello track light using a standard wall switch connected to the fixture's circuit.
Dimming Functionality
This fixture is compatible with most standard LED dimmer switches. For optimal performance and to avoid flickering or buzzing, ensure you use a dimmer specifically designed for LED lighting. Consult the dimmer manufacturer's instructions for proper installation and operation.
Maintenance
- Cleaning: Always turn off power and allow the fixture to cool before cleaning. Wipe the fixture with a soft, dry, or slightly damp cloth. Do not use abrasive cleaners, solvents, or polishes as they may damage the finish.
- LEDs: The integrated LED light sources are designed for long life and are not user-replaceable. Do not attempt to replace the LEDs.
- Inspection: Periodically inspect the fixture for any signs of damage or loose connections. If any issues are found, disconnect power and consult a qualified electrician.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on. | No power to the fixture. Loose wire connection. Faulty wall switch. | Check circuit breaker. Ensure all wire connections are secure (with power off). Test or replace wall switch. |
| Light flickers or buzzes. | Incompatible dimmer switch. Loose wire connection. | Ensure an LED-compatible dimmer is used. Check wire connections (with power off). |
| Light output is low. | Dimmer setting too low. | Adjust dimmer to a higher setting. |
If you experience issues not listed here or if troubleshooting steps do not resolve the problem, contact EGLO customer support or a qualified electrician.
Specifications
| Brand: | EGLO |
| Model Name: | 201222A |
| Color: | Black |
| Material: | Alloy Steel (Fixture), Glass (Shade) |
| Style: | 4-Light Track Head |
| Product Dimensions (L x W x H): | 31.25" x 5.12" x 5.25" |
| Power Source: | Corded Electric |
| Light Source Type: | Integrated LED |
| Number of Light Sources: | 4 |
| Voltage: | 120 Volts |
| Wattage: | 4.2 Watts (per light source, total 16.8W) |
| Dimmable: | Yes (with compatible LED dimmer) |
| Assembly Required: | Yes |
| Mounting Type: | Protruding (Wall or Ceiling) |
| Certifications: | UL Listed |
| Item Weight: | 3.45 pounds |

Image: A diagram illustrating the key dimensions of the EGLO Lianello track light, including its 31.25-inch length.
Warranty and Support
Warranty Information
All products purchased have a 30-day replacement parts policy to ensure a fully working item. All products are covered under a 1-year warranty when purchased on Amazon. The warranty period begins on the day the product is originally shipped. The warranty covers all of the items and conditions identified in the original manufacturer's warranty. Some of the items specifically not covered by the warranty are loss and theft, water damage, customer abuse, and finish deterioration due to UV or coastal exposure.
Customer Support
For technical assistance, replacement parts, or warranty claims, please contact EGLO customer support. Refer to the EGLO website or your purchase documentation for current contact information.
You can visit the official EGLO store for more information: EGLO Store on Amazon
About EGLO
EGLO is a leading manufacturer of light fixtures, committed to providing innovative and stylish lighting solutions. The following video offers a glimpse into the EGLO brand and its diverse range of products.
Video: An official EGLO brand video showcasing various lighting products and design concepts. This video provides an overview of the brand's commitment to quality and design in the lighting industry.
Ask a question about this manual
Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.







