Lenco CR-07 Pink

Lenco CR-07 Pink Alarm Clock Radio User Manual

Model: CR-07 Pink | Brand: Lenco

Introduction

This user manual provides comprehensive instructions for the Lenco CR-07 Pink Alarm Clock Radio. Please read this manual carefully before operating the device to ensure proper use and to prevent damage. Keep this manual for future reference.

Safety Information

Product Overview

Familiarize yourself with the components and controls of your Lenco CR-07 Alarm Clock Radio.

Lenco CR-07 Pink Alarm Clock Radio, front and top view

Figure 1: Front and top view of the Lenco CR-07 Pink Alarm Clock Radio. This image shows the main display with red LED digits, the Lenco logo, and the control buttons on the top panel. The top panel is black with a ribbed texture, and the side panels are pink.

Close-up of control buttons on Lenco CR-07 Pink Alarm Clock Radio

Figure 2: Close-up view of the control panel. Buttons visible include a large "SNOOZE" button, "ON.OFF", "Preset: M+", "TU-", "HR", "MIN", "TU+", "VOL-", and "VOL+". These buttons are used for setting time, alarms, tuning the radio, and adjusting volume.

Close-up of digital display on Lenco CR-07 Pink Alarm Clock Radio

Figure 3: Detailed view of the digital display. The display shows the time in large red LED digits. To the left, there are icons for Alarm 1 (bell with '1') and a music note. To the right, there are icons for Alarm 2 (bell with '2'), another music note, and a 'Zz' icon for snooze/sleep functions. The Lenco logo is centered below the time display.

Control Buttons:

Setup

1. Unpacking

Carefully remove the alarm clock radio from its packaging. Retain the packaging materials for future transport or storage if needed.

2. Powering the Device (Battery Installation)

The Lenco CR-07 is battery-powered. Locate the battery compartment on the underside of the unit. Insert the required batteries (e.g., 2 x AAA or AA, check compartment for specific type) ensuring correct polarity (+/-). Close the battery compartment cover securely.

3. Initial Time Setting

  1. Press and hold the Clock Icon button (if available) or a dedicated TIME SET button. The display digits should start flashing.
  2. Use the HR button to set the hour.
  3. Use the MIN button to set the minute.
  4. Press the Clock Icon button again or wait a few seconds for the time to be set.

Operating Instructions

Power On/Off

Setting Alarms (Alarm 1 & Alarm 2)

  1. Press the Alarm 1 button (bell with '1' icon) once. The alarm time digits will flash.
  2. Use the HR button to set the desired alarm hour.
  3. Use the MIN button to set the desired alarm minute.
  4. Press the Alarm 1 button again to confirm and activate Alarm 1. The Alarm 1 icon will appear on the display.
  5. Repeat the process using the Alarm 2 button (bell with '2' icon) to set and activate Alarm 2.
  6. To deactivate an alarm, press its respective alarm button until the alarm icon disappears from the display.

Radio Operation

  1. Press the ON.OFF button to turn on the radio.
  2. Use the TU- or TU+ buttons to manually tune to your desired radio frequency. Press and hold for automatic scanning.
  3. Adjust the volume using the VOL- or VOL+ buttons.

Saving and Recalling Presets:

  1. Tune to the desired radio station.
  2. Press and hold the Preset: M+ button until the display shows a preset number (e.g., "P01").
  3. Use the TU- or TU+ buttons to select the desired preset number (e.g., P01, P02, etc.).
  4. Press Preset: M+ again to confirm and save the station to that preset.
  5. To recall a saved preset, short press the Preset: M+ button repeatedly to cycle through the saved stations.

Snooze Function

When an alarm sounds, press the large SNOOZE button to temporarily silence the alarm. The alarm will sound again after a few minutes (typically 9 minutes). The 'Zz' icon may flash on the display.

Stopping the Alarm

To stop an alarm completely, press the ON.OFF button. The alarm will reset for the next day.

Maintenance

Cleaning

Wipe the unit with a soft, dry cloth. Do not use abrasive cleaners or solvents. Ensure no liquids enter the unit.

Battery Replacement

When the display dims or the unit functions erratically, it's time to replace the batteries. Open the battery compartment, remove old batteries, and insert new ones, observing correct polarity. Dispose of old batteries responsibly according to local regulations.

Troubleshooting

ProblemPossible CauseSolution
Unit does not power on.Batteries are dead or incorrectly inserted.Replace batteries with new ones, ensuring correct polarity.
Radio reception is poor.Weak signal; unit position.Adjust the position of the unit or extend the antenna (if applicable). Try tuning manually.
Alarm does not sound.Alarm not set or deactivated; volume too low.Ensure alarm is activated (icon visible). Increase volume.
Time display is incorrect.Time not set correctly; power interruption.Reset the time following the "Initial Time Setting" instructions.

Specifications

FeatureDetail
Model NumberCR-07 Pink
BrandLenco
Product Dimensions (L x W x H)4.17 x 4.33 x 2.01 inches
Item Weight11.4 ounces (324 Grams)
Power SourceBattery Powered (3 Volts)
Display TypeDigital LED
Frequency50 Hz
StyleCompact

Note: Specifications are subject to change without notice.

Warranty Information

Lenco products are manufactured to high quality standards. This product is covered by a limited warranty against defects in materials and workmanship. For specific warranty terms and conditions, please refer to the warranty card included with your product or visit the official Lenco website.

Customer Support

For further assistance, technical support, or service inquiries, please contact Lenco customer support. You can find contact details on the official Lenco website or in the product packaging.

Website: www.lenco.com (Example link, actual link may vary)

Related Documents - CR-07 Pink

Preview Lenco CR-07 Blue User Manual and Safety Precautions
This document provides essential safety precautions and installation guidelines for the Lenco CR-07 Blue alarm clock radio. It covers important information regarding safe operation, environmental considerations, and proper setup to ensure optimal performance and user safety.
Preview Lenco CR-18 PLL FM Alarm Clock Radio User Manual
User manual for the Lenco CR-18 PLL FM Alarm Clock Radio. Learn how to set the time, alarms, operate the FM radio, use the sleep timer, and adjust brightness. Features a 1.8-inch LED display and a white finish.
Preview Lenco CR-07 Clock Radio User Manual and Safety Precautions
Comprehensive safety guidelines and installation instructions for the Lenco CR-07 clock radio. This document details precautions for electrical use, battery handling, environmental factors, and proper setup to ensure safe and optimal operation.
Preview Lenco CR-18 Clock Radio User Manual and Safety Guide
Comprehensive user manual for the Lenco CR-18 clock radio, providing detailed instructions on setup, operation, safety precautions, technical specifications, warranty, and disposal.
Preview Lenco CR-615 DAB+/FM Clock Radio with Time Projection User Manual
Comprehensive user manual for the Lenco CR-615 clock radio, detailing its features, operation, setup, and safety precautions. Includes instructions for DAB/FM radio, alarm settings, and time projection.
Preview Lenco CR-18 Alarm Clock Radio User Manual
Comprehensive guide for the Lenco CR-18 alarm clock radio, detailing features, operation, safety precautions, and specifications. Includes multilingual instructions.