Introduction
The Kokido K385 Waterfall Fountain is designed to add both aesthetic appeal and a relaxing sound to your swimming pool. This device connects to your pool's water return, creating a decorative waterfall effect. It is suitable for both in-ground and above-ground pools, excluding soft-wall types. The fountain can be easily installed and adjusted, and can be pivoted underwater when the waterfall feature is not desired.
Safety Information
Always ensure your pool pump is turned off before installing or performing any maintenance on the waterfall fountain. Do not allow children to play with or hang on the fountain. Ensure all connections are secure to prevent leaks and maintain proper water circulation. A 1/2HP pump is required for optimal operation of this fountain.
Package Contents
Upon opening the package, verify that all components of your Kokido K385 Waterfall Fountain are present and undamaged. The package should contain the main fountain assembly, which includes the threaded connector, vertical pipe, elbow joint, and horizontal spray bar.
Image: Components of the Kokido K385 Waterfall Fountain, showing the threaded base, vertical pipe, elbow, and horizontal spray bar.
Setup
- Prepare Pool Return: Ensure your pool pump is off. Locate the 1.5-inch threaded return fitting in your pool. If an eyeball socket or other fitting is present, remove it to expose the internal threads.
- Assemble Fountain: Connect the vertical pipe to the threaded base. Attach the elbow joint to the top of the vertical pipe, and then connect the horizontal spray bar to the elbow joint. Ensure all connections are hand-tightened securely.
- Install Fountain: Thread the assembled fountain into the 1.5-inch threaded return fitting of your pool. Tighten until snug, ensuring the fountain is oriented correctly.
- Positioning: Adjust the angle of the horizontal spray bar to direct the water flow as desired. The fountain can be positioned to spray water into the pool or pivoted underwater when not in use.
Image: The Kokido K385 Waterfall Fountain installed in a swimming pool, actively creating a waterfall effect.
Operating
Once installed, turn on your pool pump. Water will flow through the fountain, creating a waterfall effect. The spray is adjustable in direction and height, reaching up to 14 feet depending on your pump's power (a 1/2HP pump is recommended). To adjust the spray height, you may need to regulate the flow from your pool's return line valve, if available.
Image: A close-up view of the Kokido K385 Waterfall Fountain, showing the water cascading into the pool.
When the waterfall feature is not desired, the fountain can be pivoted underwater. This allows it to remain connected to the return fitting without creating a spray, effectively hiding it from view.
Image: The Kokido K385 Waterfall Fountain pivoted downwards, submerged in the pool, demonstrating its ability to be hidden when not in use.
Maintenance
Regularly inspect the fountain for any debris or mineral buildup that might obstruct the water flow. Clean the spray bar and internal components as needed using a soft brush and mild pool-safe cleaner. During off-season or when not in use for extended periods, it is recommended to remove the fountain from the pool, clean it thoroughly, and store it in a dry, protected area to prolong its lifespan.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Weak or no water spray | Insufficient pump power; Clogged spray bar; Loose connections; Low pool water level. | Ensure a 1/2HP pump is used; Clean the spray bar; Tighten all connections; Adjust pool water to optimal level. |
| Water leaking from connections | Loose fittings; Damaged O-rings/gaskets. | Hand-tighten all connections firmly; Inspect and replace O-rings or gaskets if damaged. |
| Fountain does not stay in desired position | Fittings not tight enough; Excessive water pressure. | Ensure all threaded connections are secure; Consider slightly reducing pump flow if pressure is too high. |
Specifications
- Product Dimensions: 6 x 12 x 12 inches
- Item Weight: 1 pounds
- Manufacturer: Robelle Industries
- Item Model Number: K385CBX
- ASIN: B008EKKY72
- Compatibility: Fits 1.5" threaded return fitting
- Pump Requirement: 1/2HP minimum
Warranty and Support
For specific warranty information and customer support, please refer to the documentation provided with your purchase or contact the manufacturer, Robelle Industries, directly. You may also visit the official Kokido store for additional product information and support resources: Kokido Store on Amazon.
